|
10-08-2017, 12:04 PM
|
|
Lateral-g Supporting Member
|
|
Join Date: Apr 2012
Location: Livermore
Posts: 2,445
Thanks: 111
Thanked 83 Times in 61 Posts
|
|
Looking for a SBC mild build complete (Nor-cal)
Like the title states, i'm pulling the Olds out of my Keaton and going sbc, much cheaper to run and get parts for. I figure with the number of LS swaps out there someone may have one laying around. Looking in Nor-cal, trying here first, don't really want to buy new or deal with c/l although i might...
Boat doesn't get used much and not sure if i want to sell, right know the Olds is bad (the shop who did the three angle grind a few years back used wrong head gaskets, long story. I didn't pay all the bill due to other unmet "promises" on their part). High quality shop too, but they only wanted to work on the "big boy boats" of which mine is not.
Cheers, mike
__________________
Mike
|
10-08-2017, 03:56 PM
|
|
Senior Member
|
|
Join Date: Oct 2013
Location: Peoria, AZ
Posts: 2,668
Thanks: 72
Thanked 337 Times in 211 Posts
|
|
Pm sent
__________________
Lance
1985 Monte Carlo SS Street Car
|
10-08-2017, 06:22 PM
|
|
Senior Member
|
|
Join Date: Feb 2016
Location: Bay Area
Posts: 190
Thanks: 90
Thanked 39 Times in 29 Posts
|
|
Buddy of mine just did an LS3 swap from a 383 sbc with a Holley TBI setup this past summer. It might still be sitting at West Coast Muffler in Concord. It was swapped out b/c it was burning oil after a fresh rebuild and he was fed up and just wanted a stock crate motor.
__________________
-Adam
1968 Camaro SS
|
10-08-2017, 07:14 PM
|
|
Senior Member
|
|
Join Date: Feb 2016
Location: Bay Area
Posts: 190
Thanks: 90
Thanked 39 Times in 29 Posts
|
|
Sorry, should have asked before posting... the SBC is already sold. Good luck!
__________________
-Adam
1968 Camaro SS
|
10-09-2017, 12:50 PM
|
|
Senior Member
|
|
Join Date: Oct 2013
Location: SF bay area
Posts: 1,127
Thanks: 1
Thanked 138 Times in 76 Posts
|
|
Small block chevy
Mike,
I don't have a chevy but do have a couple of Pontiac engines
will bolt in place of the Olds engine
455 fairly stock with new crank and cam.. $3200 no dizzy,carb or manifold
428 actually 440 with steel crank, killer rods, polished manifold, ported
#16 heads.. cam was flat so new cam, lifters and bearings $4200
I can send flyers if you are interested
Bob- Panteracer and Dreamin Tas
|
10-09-2017, 01:31 PM
|
|
Senior Member
|
|
Join Date: Oct 2013
Location: SF bay area
Posts: 1,127
Thanks: 1
Thanked 138 Times in 76 Posts
|
|
Small Block Chevy
Mike,
I do have a fairly stock small block
with a high rise, new edelbrock carb,gear drive,
recently rebuilt.. It is in my 63 truck I
bought and I am toying with putting one
of the Pontiac engines in it.... you can hear
it run....
$1500 for the chevy
Bob- Panteracer
|
10-10-2017, 01:42 PM
|
|
Lateral-g Supporting Member
|
|
Join Date: Apr 2012
Location: Livermore
Posts: 2,445
Thanks: 111
Thanked 83 Times in 61 Posts
|
|
thanx Bob, i dont think the pontiac head will sync with the olds, and at 1500-2000 exhaust, it wouldnt deem itself cost effective.
May be interested in the chevy though.....thanx
__________________
Mike
|
10-10-2017, 02:33 PM
|
|
Senior Member
|
|
Join Date: Oct 2013
Location: SF bay area
Posts: 1,127
Thanks: 1
Thanked 138 Times in 76 Posts
|
|
Small Block Chevy
Got it...
Let me know if you want to hear or see the chevy
I could maybe meet you some place or you can come
to my shop in Campbell.. thinking one of the Pontiacs
is going in the truck
Bob
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 06:54 AM.
|