...

Go Back   Lateral-g Forums > Technical Discussions > Engine
User Name
Password



Reply
 
Thread Tools Display Modes
  #61  
Old 03-18-2010, 10:52 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

From flywheel to accessories just North of 20k.
__________________
Todd
Reply With Quote
  #62  
Old 03-18-2010, 11:07 PM
Steve1968LS2's Avatar
Steve1968LS2 Steve1968LS2 is offline
Moderator
 
Join Date: Feb 2005
Location: Anaheim Hills, CA
Posts: 5,533
Thanks: 0
Thanked 4 Times in 2 Posts
Default

Very cool.. and very nice photography..

I leave for Vegas in the morning.. going to cover and autocross at the Super Chevy show..
__________________
"A ship in port is safe, but that's not what ships are built for."

See Bad Penny run the cones: https://www.youtube.com/watch?v=8GUPPIX-92U

1971 Chevelle Wagon - Roadster Shop Chassis ProCharged Shafiroff LS and lots of yada yada

1968 Camaro - Project Track Rat - 440 RHS LS
Reply With Quote
  #63  
Old 03-18-2010, 11:16 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

I was hoping to make the Super Chevy event but I'm turning the key at the earliest tomorrow night. I want to put some shake down miles on it before I hail Mary the car. I was really hoping to show those car show guys what's up.
__________________
Todd
Reply With Quote
  #64  
Old 03-19-2010, 06:01 AM
ProdigyCustoms ProdigyCustoms is offline
Senior Member
 
Join Date: Mar 2005
Posts: 3,859
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Its a roller motor, it has already been dynoed and broke in, your ready, go to the track! I have warmed up my motors and taken to the track for 30 years! No worries. if it survived the dyno, your good to go.
__________________
Frank Serafine
Reply With Quote
  #65  
Old 03-19-2010, 08:58 AM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

I'm not worried about that, it's more to due with the new clutch, oil lines, cooling system and any carb tweaks. I also need to re dial in the ride height since it's on the ground and sitting a full inch higher up front without the hood and seats. Sunday is not out of the question.
__________________
Todd

Last edited by Vegas69; 03-19-2010 at 09:30 AM.
Reply With Quote
  #66  
Old 03-23-2010, 08:10 PM
g356gear's Avatar
g356gear g356gear is offline
Senior Member
 
Join Date: Oct 2008
Posts: 659
Thanks: 0
Thanked 8 Times in 2 Posts
Default

I think you mentioned the motor was approx 150 lbs lighter than the old motor. Did you have to change front spring rates?
__________________
69 SS396 Camaro Coupe, 4link, 12bolt posi, Speedtech LCA and UCA's, Hotchkis 2" drop springs and sway bar, Ridetech triple remote resevoir coilovers, Bilsteins, Wilwood 6 piston front/4 piston rear, Magnaflow stainless exhaust, Lemons Headers, Comp rollers/p-rods/cam, Fikse 18x8.5 and 18x10
Reply With Quote
  #67  
Old 03-23-2010, 09:02 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

I have yet to drive the car but it already had LSX/Small block springs. I took two turns out of the coil overs and it's close.
__________________
Todd
Reply With Quote
  #68  
Old 03-23-2010, 09:06 PM
BA. BA. is offline
Member
 
Join Date: Mar 2005
Location: Miamisburg, Ohio
Posts: 22
Thanks: 0
Thanked 0 Times in 0 Posts
Default

WOW! That sounded freakin great!

I can't believe I'm missing out on this good stuff by being at the other place too much!

Can't wait to see/hear some road video.
Reply With Quote
  #69  
Old 03-23-2010, 09:54 PM
lil427z's Avatar
lil427z lil427z is offline
Senior Member
 
Join Date: Dec 2004
Posts: 865
Thanks: 0
Thanked 0 Times in 0 Posts
Default

motor porn sounds good.
rick k
Reply With Quote
  #70  
Old 03-25-2010, 08:00 PM
g356gear's Avatar
g356gear g356gear is offline
Senior Member
 
Join Date: Oct 2008
Posts: 659
Thanks: 0
Thanked 8 Times in 2 Posts
Default

Quote:
Originally Posted by Vegas69 View Post
From flywheel to accessories just North of 20k.
And for just the GM ZL1 block?
__________________
69 SS396 Camaro Coupe, 4link, 12bolt posi, Speedtech LCA and UCA's, Hotchkis 2" drop springs and sway bar, Ridetech triple remote resevoir coilovers, Bilsteins, Wilwood 6 piston front/4 piston rear, Magnaflow stainless exhaust, Lemons Headers, Comp rollers/p-rods/cam, Fikse 18x8.5 and 18x10
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:56 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net