...

Go Back   Lateral-g Forums > Technical Discussions > Engine
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 07-03-2013, 04:34 PM
hiwayman hiwayman is offline
Senior Member
 
Join Date: Jan 2006
Location: new zealand
Posts: 121
Thanks: 0
Thanked 0 Times in 0 Posts
Default 1050 braswell 3circuit

hey guys have this on a small block yip way to big had the combo on the dyno no drama but as soon as i try to idle/ cruse way to rich will kill the plugs has any blocked the intermidiate circuit
































hey guys super rich at idle here are the carb spec 28high speed 51intermidiate 29idle air bleed 79primary jet 85power valve 92cscondary no pv in rear mixtuer screws 3/4 turn out primary blades set so transfer slot is square cam at .050 intake250 exuast256 valve lift in624 ex605 any starters thanks
Reply With Quote
  #2  
Old 07-03-2013, 05:09 PM
Ron Sutton's Avatar
Ron Sutton Ron Sutton is offline
Senior Member
 
Join Date: May 2013
Location: Folsom, CA
Posts: 2,422
Thanks: 45
Thanked 35 Times in 26 Posts
Default

How much "steady vacuum" are you seeing at idle & cruise?
__________________
Ron Sutton Race Technology
Reply With Quote
  #3  
Old 07-03-2013, 05:23 PM
Ron Sutton's Avatar
Ron Sutton Ron Sutton is offline
Senior Member
 
Join Date: May 2013
Location: Folsom, CA
Posts: 2,422
Thanks: 45
Thanked 35 Times in 26 Posts
Default

Also ...

a. Does the intermediate circuit have a removable jet type of orifice in your carb's metering body?

b. Does it seem to be a "similar amount too rich at both idle & cruise rpm" ... or is does one seem richer than the other ?

c. Are the emulsion orifices simply drilled holes ... or removable jet type orifices?

d. 3-circuit carbs are designed to be richer on the low end. So I don't normally see them in this application. Did you buy this carb for this application? Is it new or used?

e. Do you have a A/F meter you can use to help dial this carb in?
__________________
Ron Sutton Race Technology
Reply With Quote
  #4  
Old 07-03-2013, 06:44 PM
intocarss's Avatar
intocarss intocarss is offline
Senior Member
 
Join Date: Aug 2011
Location: So Cal in the Sfv
Posts: 4,257
Thanks: 0
Thanked 0 Times in 0 Posts
Default

This?

http://motorsportsvillage.com/forum/...php?f=6&t=9717

http://motorsportsvillage.com/forum/...=9316&start=15
__________________
If it ain't buckin, chirpin & makin all kinds of bad noises, then I ain't happy

Accelerating is optional...........stopping is mandatory. Your car WILL stop one way or another.
Reply With Quote
  #5  
Old 07-03-2013, 06:50 PM
Ron Sutton's Avatar
Ron Sutton Ron Sutton is offline
Senior Member
 
Join Date: May 2013
Location: Folsom, CA
Posts: 2,422
Thanks: 45
Thanked 35 Times in 26 Posts
Default

I would say all the help he needs is right there.
__________________
Ron Sutton Race Technology
Reply With Quote
  #6  
Old 07-03-2013, 09:34 PM
intocarss's Avatar
intocarss intocarss is offline
Senior Member
 
Join Date: Aug 2011
Location: So Cal in the Sfv
Posts: 4,257
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Ron Sutton View Post
I would say all the help he needs is right there.
I hope so, I did it to my drag car and it helped a lot
__________________
If it ain't buckin, chirpin & makin all kinds of bad noises, then I ain't happy

Accelerating is optional...........stopping is mandatory. Your car WILL stop one way or another.
Reply With Quote
  #7  
Old 07-03-2013, 11:16 PM
hiwayman hiwayman is offline
Senior Member
 
Join Date: Jan 2006
Location: new zealand
Posts: 121
Thanks: 0
Thanked 0 Times in 0 Posts
Default

hi guys thanks for the replys here goes carb came with engine it does have screw in bleeds on the intermidate circuit thers no provison for vacume gauge but there is a blank spot at the front so will drill and tap it the emulsions are not screw in type but there is small bleeds at top of meter block on the PVside and screw in bleeds/jets right next to the main jets will purchase a/f meter i will post sum pics of the carb tomoro im in NZ so be sum time delay and thanks again also runs real rich at idle and cruise

Last edited by hiwayman; 07-03-2013 at 11:23 PM.
Reply With Quote
  #8  
Old 07-03-2013, 11:21 PM
hiwayman hiwayman is offline
Senior Member
 
Join Date: Jan 2006
Location: new zealand
Posts: 121
Thanks: 0
Thanked 0 Times in 0 Posts
Default

hi intocarsss yea iv been trying to get my brain around that conversion it seems the go but phew i dont were to start think il read again
Reply With Quote
  #9  
Old 07-04-2013, 11:22 AM
intocarss's Avatar
intocarss intocarss is offline
Senior Member
 
Join Date: Aug 2011
Location: So Cal in the Sfv
Posts: 4,257
Thanks: 0
Thanked 0 Times in 0 Posts
Default

TAKE A LOOK AROUND THIS SITE TOO

http://racingfuelsystems.myfunforum....e8bf54f245f780
__________________
If it ain't buckin, chirpin & makin all kinds of bad noises, then I ain't happy

Accelerating is optional...........stopping is mandatory. Your car WILL stop one way or another.
Reply With Quote
  #10  
Old 07-05-2013, 10:40 PM
hiwayman hiwayman is offline
Senior Member
 
Join Date: Jan 2006
Location: new zealand
Posts: 121
Thanks: 0
Thanked 0 Times in 0 Posts
Default

update cleaned the carb with crc carb clean and blew out all orifices etc same with plugs cnected vacume guage also took out the 29 idle airs and straight to sum 72 well fiered it up and massive change no were near as rich got idle vac at 7.5hg makes the installed 85power valve not correct were to from here?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:32 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net