...

Go Back   Lateral-g Forums > Lateral-G Open Discussions > Project Updates
User Name
Password



Reply
 
Thread Tools Display Modes
  #91  
Old 09-14-2018, 10:45 AM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default



All hoses and Clamps are finally in place, now I can book time for inspection of the build for my registration as a modified vehicle.

That has to get approved before I can mount body again.
Reply With Quote
The Following User Says Thank You to warhawkchevelle For This Useful Post:
syborg tt (10-03-2018)
  #92  
Old 09-16-2018, 01:09 AM
1965_SS's Avatar
1965_SS 1965_SS is offline
Senior Member
 
Join Date: Oct 2010
Location: Central Valley, CA
Posts: 257
Thanks: 30
Thanked 15 Times in 13 Posts
Default

Quote:
Originally Posted by warhawkchevelle View Post


Slow progress, its a lot of planning to remember all parts when ordering from your country and getting it to Sweden

The axle and brakes are finally assembled and I will measure and order braided brakehoses tomorrow.

Im getting it registered as a modified vehicle so I need to get a build inspection Done before I can mount body also.

Regarding venting of rear axle, I have AN3 male barb on housing.
Any ideas for filter or roll over valve or What have you used?

Looks great! You can check out this for a vent: https://www.iimuch.com/
__________________
_________
Todd
1965 Chevelle SS
Project Build
Reply With Quote
  #93  
Old 09-17-2018, 09:15 PM
TheWraith's Avatar
TheWraith TheWraith is offline
Junior Member
 
Join Date: Jul 2012
Location: DFW
Posts: 11
Thanks: 0
Thanked 1 Time in 1 Post
Default

Looks great and way to improve after a setback.
Reply With Quote
  #94  
Old 09-28-2018, 12:41 PM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default



We have touchdown! 😁😁😁

Frontclip goes on tomorrow!
Reply With Quote
The Following User Says Thank You to warhawkchevelle For This Useful Post:
syborg tt (10-03-2018)
  #95  
Old 09-30-2018, 10:35 AM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default



Now the car is back at home.
Next step is to rewire the car with the American Autowire kit and do the wiring for my Fueltech FT500 EFI system
Reply With Quote
The Following User Says Thank You to warhawkchevelle For This Useful Post:
syborg tt (10-03-2018)
  #96  
Old 10-04-2018, 12:53 PM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default



Ron Davis radiator fits and looks really good





Had a radio delete panel so thats where the FT500 dash/ECU will dit. Gotta get it chromed and painted also before I install.

A buddy left his Drag Week Corvette in USA so he is flying over in november and upgrading it so he’s bringing home a Dakota Digital RTX for me.
Reply With Quote
  #97  
Old 10-04-2018, 06:26 PM
WSSix WSSix is offline
Lateral-g Supporting Member
 
Join Date: Nov 2008
Location: Dunwoody, GA
Posts: 6,287
Thanks: 646
Thanked 566 Times in 460 Posts
Default

Congrats! That's quite the accomplishment. The car is looking good! Hope you have a productive winter this year finishing the car.
__________________
Trey

Current rides: 2000 BMW 540i/6 and 86 C10.

Former ride: 1979 Trans Am WS6: LT1/T56, Kore 3 C5/6 brakes, BMW 18in rims
Reply With Quote
The Following User Says Thank You to WSSix For This Useful Post:
warhawkchevelle (10-05-2018)
  #98  
Old 10-05-2018, 12:11 AM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default

Thank you!
We`ll see if I have enough time, energy and money to finish it this winter.
Waiting on a new sled also, hoping for a lot of deep snow and steep hills this winter also
Attached Images
 
Reply With Quote
  #99  
Old 10-13-2018, 03:16 PM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default



Me and a buddy started to design supercharger brackets tonight. He is drawing it up in Solidworks so we can do a first mockup.
Reply With Quote
  #100  
Old 11-10-2018, 12:45 AM
warhawkchevelle warhawkchevelle is offline
Senior Member
 
Join Date: Jun 2016
Location: Sweden
Posts: 148
Thanks: 109
Thanked 286 Times in 81 Posts
Default

Had to redo my transmission tunnel, didnt get good angles so I lifted the Tremec in the rear.



Trailerhitch in place



New sled is here ❤️
Reply With Quote
The Following User Says Thank You to warhawkchevelle For This Useful Post:
lawrenq (02-24-2019)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:05 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net