icemanrd19 67 camaro

[randy]

https://scontent.xx.fbcdn.net/v/t1.0-9/17352543_10101112013523266_1906976037101606383_n.j pg?oh=010d0d323227186a2eddb5033c8ff605&oe=5953B3F6



Well about 3 or 4 months ago i bought a 1967 Camaro from a guy in fort worth. Well Replacing a few nuts and bolts led me to ripping alot of the car apart. Currently the car is sitting apart and im trying to figure out what direction i want to take it.

I need some help with the steps of fixing this car up the way i want it. I stopped last month bc i felt like i was probably going to do things to the car that i would end up having to take back off so in essence wasting my time.

Exterior
2002 plymouth prowler orange
Marquez billet taillights P/N 103-bc
DSE selecta - speed wiper kit P/N 121001 wired into stock fuse box
Ringbrothers black air frame 20679-1032 hood hinges
Stock hood latch painted black
Forgeline rims 18x9.5 and 18x11 polished outers titanium smoked centers, Fronts 28.58 offset, hub 70.3, rears 25.4 offfset and 70.3 hub
315/30/18 and 275/35/18 michelin ps2 tires
Dse mini tubbed
Dse subframe connectors
Ridetech billet gas cap
RS lower valance with new lights tinted black
Stock 68 camaro mirrors mr-27 and mr-26. First hole is drilled 1 inch up and 8 inches back on the door
68 camaro rs kit with Retro - Electro PN-002 RS Electronic Headlight kit
New rear quarters, trunk, tailpan, hood, roof, floor, dash, and radiator support
New door handle kit part # dw-60p
New rear bumper
Smoothed firewall
aluminum hood strikers

Suspension and Brakes
2012 corvette z06 6 piston calipers with 6 puck pads and 4 piston rear calipers with stock rotors
Kore 3 rear parking brake kit1988-1995 corvette rear ebrake cables ac delco part number 19143763
67 camaro big block intermediate cable pbk-11r
front cable pbk-10a, New e-brake, Drill out the kore 3 bracket to 9/16"
Hydroboost unit with wilwood Master cylinder street quality P/N 2021-STP
Dse front subframe P/N 032006
Dse rear quadralink P/n DS-041703 with ridetech single adjustable shocks
ford 9" moser custom alloy 31 spline axle shafts torino flanged OD 6.9 or less/ press on bearings
1/2"-20x 3.00" studs press in GM 5 of 4 3/4 bolt circle, 1/2" pinion offset
"f" measurement 25.375?""g" measurement 24.375" Total axle width 54/750 axle flange to axle flange
moser 9" ford complete 3rd member Truetrack 31 spline Diff n-case daytona aluminum pinion support 1250 yoke w/u-bolt 4.11 gear ratio
Wilwood proportioning valve 260-11179, wilwood master cylinder and hydroboost
Chassisworks tunel kit P/N 5922-f10
Dse aluminum body bushings


Interior
Eddie motorsports black steering wheel launch MS140-54BK
Morris Classic concepts 3 point setbelts
American autowire kit
Dynalined and Dynamat entire metal part of the car
Rear sony 6x9s using the speaker covers as a spacer
Kick panels with speakers
New stock 67 dome light
New stock 67 rearview mirror
69 camaro rear quarter outer felts with the flag
TMI one piece suede headliner
recaro seats with suede middle inserts
County prison white shift knob P/N sk502-cpbk-6rur on a Finch 6" shifter P/N 7000461-n
New rear quarters, trunk, tailpan, hood, roof, floor, dash, and radiator support
Vintage air unit with modified DSE vintage air bracket P/N 011006
dw-20 door mechanisms
cpt-07p fisher logo sill plates
bm-1048 quarter glass vertical moldings
dw-27 window cranks
ws-09 u-jamb seats
gb-16 glove box door bumper set
rsp-11bk black mesh package tray
DJ-100 windsock end caps


Engine
vaporworx fuel tank with notched corners with 2012 camaro fuel pump
T56 reverse lockout from wire barn t56-CON
Billet specialties 77109 overflow tank
PRC dual pass radiator 211001 and spal fan setup
ls3 480hp rated at 495 with hotcam
t56 magnum/ ls7 clutch
Afco dynatech 2.5 exhaust 793-91125
Holley black fuel rails p?n 534-209
Finch performance gas/diff dual vent system
Kwik Performance P/N k10143 air conditioner bracket kit
autocraft oil pan
Corvette accessories 19257325
Elite Engineering Catch can CC-200B
PCM of NC p-150028 A/C fan speed bump circuit and PCM of NC Hi/Lo speed Fan Kit
DSE battery relocation kit
stainless works headers part number ca679wd 1.75 primaries and 3" slip fit collectors
dse motor mounts 060401






ws-18 cowl hood to vent seal
ws-47 cowl vent wedges
Part # ws-05 trunk weatherstrip
Part # ws-19 67 OEM window felt set
lic-15 license plate bumper set



http://i30.photobucket.com/albums/c302/icemanrld19/photo5.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/photo4.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/photo2.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/photo1.jpg

[randy]

THis is exactly how i want my 67
http://i30.photobucket.com/albums/c302/icemanrld19/efc7cfa2.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/1d6705f6.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/c6f6b540.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/86036004.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/4be6c498.jpg

THis was my old project but ive grown up now to bigger meaner toys :)
http://i30.photobucket.com/albums/c302/icemanrld19/DSCF1368.jpg

[KPC67]

Nice Car:thumbsup:
My opinion is to keep it driving. I would start with the mini tubs, and rear suspension (my choice is DSE) Then put back on the road. Keep upgrading it as you go.
My personal experience is that my car has been in the shop stripped right down, I am not able to drive it because I cannot afford to do everything I want to do all at once.
Just my .02

[randy]

well in order for me to drive it again i need to rewire the entire car. I dont feel like ripping all the wiring out and doing it all over again. Thats my dilemma. Plus i need to smooth the firewall out and in order to do that ill probably have to pull the motor.

[nvr2fst]

[QUOTE=randy;334398]THis is exactly how i want my 67 Then you should have bought a 69:lol: Sorry but I had to, after u posted the photo of a 69. Youll be in good hands around here and many will give you helpful advise.:thumbsup:

http://i30.photobucket.com/albums/c302/icemanrld19/efc7cfa2.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/1d6705f6.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/c6f6b540.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/86036004.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/4be6c498.jpg

[randy]

Can i get some opinions about the G link setup with mini tubs? I understand dse is suppose to be the best but how does it compare to G link and price wise?

[youthpastor]

cool project!

there are lots of options for suspension and subframes out there. I've learned so much from the Lat-G gang.

I am a big fan of DSE, Art Morrison and I really like dealing with the Speedtech boys.

enjoy the process:D

[randy]

what should i expect to pay for a quality 4 link and rear end setup? Should i go with the 12 bolt gm or 9" ford? why one over the other? sorry im a newb when it comes to this type of stuff

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/166c100d.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/73e95dc1.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/7b425f26.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/bb8c2eac.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/1dd3a912.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/5d74a585.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/eea1c36b.jpg

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/4ae57464.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/a2d08d8a.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/a1751c27.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/6ccb6bf6.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/381bbbcd.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/eb46dac1.jpg


Some update photoshttp://i30.photobucket.com/albums/c302/icemanrld19/ac043930.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/1b7fd360.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/90563f1f.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/0adab971.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/f40958fc.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/765187ad.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/487a8713.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/31cd482d.jpg

[randy]

Also ordered my ls2 with 6 speed transmission as well as all of this


Item Qty Price Total
FW01A_B
67 Camaro Firewall Without A/C (01B) $309.95/ea $309.95
FLP46A
67-69 Camaro Full Floor Pan with Tunnel $350.00/ea $350.00
FR07_08
67 Camaro Full Frame Rail Right Hand (FR08) $159.95/ea $159.95
WH01_02
67-68 Camaro Outer Wheelhouse Panels Left (drivers) side WH-01 $54.95/ea $54.95
WH01_02
67-68 Camaro Outer Wheelhouse Panels Right (passengers) side WH-02 $54.95/ea $54.95
TRK1046B
67-68 Camaro Full Trunk Floor with Braces $329.00/ea $329.00
TRK09_12
67-69 Camaro Trunk Drop Off (09) 67-68 RH - Passenger Side $34.95/ea $34.95
TRK09_12
67-69 Camaro Trunk Drop Off (10) 67-68 LH - Drivers Side $34.95/ea $34.95
TRK39
67-69 Camaro Trunk Gutter Set $54.95/ea $54.95
QTR09_10
67 LH and RH Camaro Full Coupe Quarter Panel LH Drivers side (09) $379.95/ea $379.95
QTR09_10
67 LH and RH Camaro Full Coupe Quarter Panel RH Passengers (10) $379.95/ea $379.95
FLP14_15
67-69 Camaro Seat Frame Support - Coupe Right (passenger) side - FLP-14 $57.95/ea $57.95
FLP14_15
67-69 Camaro Seat Frame Support - Coupe Left (Drivers) side - FLP-15 $57.95/ea $57.95
RS-68CKIT_68KIT
68 Camaro RS Headlamp Conversion Kit Chrome Trim $1150.95(68CKIT) $1,150.95/set $1,150.95
DSH-1068CA
67 Camaro Complete Dash Panel Steel $299.95/ea $299.95
KP-678WSB_69WSB
67-69 Camaro Aftermarket Kick Panels with 80 Watt KHE Speakers 67-68 (678WSB) $145.00/pr. $145.00

[KPC67]

well it looks like you are into it now:cheers:

[randy]

well it looks like you are into it now:cheers:

yup. We are ready to start replacing the floor now.

[BritishGreen68]

Where did you get the RS grille?

[randy]

firewheel classics. They are literaly 15 min from me so i dont have to pay shipping

[randy]

some progress.

http://i30.photobucket.com/albums/c302/icemanrld19/880b6d0b.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/badbf89f.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/3029104a.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/b4ce8289.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/8a6b3331.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/dc68966e.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/15fc67d3.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/7ad15be8.jpg

Im not sure whos car this is but i love the color. Yes i know its been done before but i think this is the color for sure
http://i30.photobucket.com/albums/c302/icemanrld19/F5597358.jpg

[waynieZ]

Nice project. Your making some great progress. I like t hat color too.

[BritishGreen68]

Prowler Orange man
http://www.lateral-g.net/rupp/

[randy]

leaning towards House of Kolor Kandy tangerine. Anyone have any experience with HOK paint? quality wise

[randy]

Well this is what i have so far and my decisions. im sure im missing something

Taillights ive decided to go with
http://i30.photobucket.com/albums/c302/icemanrld19/tintedtail.jpg

Headlights with the chrome ring. I will be painted the lower rs lights black too
http://i30.photobucket.com/albums/c302/icemanrld19/DSC06301.jpg

color my car will be painted. I will also have 20% window tint and the vertical window trim will be blacked out so only the outer chrome drip rail, front and rear window trim will be chrome
http://i30.photobucket.com/albums/c302/icemanrld19/humm.jpg

lower valance spoiler will be color matched too
http://i30.photobucket.com/albums/c302/icemanrld19/camarofront-1.jpg


Trunk will be smooth like this. I will be adding subs like i did to my spyder
http://i30.photobucket.com/albums/c302/icemanrld19/6157709.jpg

http://i30.photobucket.com/albums/c302/icemanrld19/MY%20spyder/DSCF0495.jpg
going with this gas cap
http://i30.photobucket.com/albums/c302/icemanrld19/b04aca2a.jpg

my cover
http://i30.photobucket.com/albums/c302/icemanrld19/00f20987.jpg

dse quadralink with narrowed ford 9" rear end
http://i30.photobucket.com/albums/c302/icemanrld19/041701-QUADRA_link_dsply.jpg

ls2 gto motor and 6 speed transmission

http://i30.photobucket.com/albums/c302/icemanrld19/ls2.jpg

[MarkM66]

Good progress. :thumbsup:

It's your car, but a painted to match front spoiler never looks good.

[randy]

Good progress. :thumbsup:

It's your car, but a painted to match front spoiler never looks good.

i started to think about this. with the texture and the likely chance of scraping it off the road i decided to leave it black. Thank you

[TrialRun]

Hey randy, it looks like its coming along nicely. Shoot me a PM, still curious what Rods Car Craft is charging ya. Thanks!

[randy]

Hey randy, it looks like its coming along nicely. Shoot me a PM, still curious what Rods Car Craft is charging ya. Thanks!
Did you get my PM? Its $50 per hr. Rodney is great to work with. If you run out of money he will hold on to the car for you as long as you like. The work is by far the best ive seen too. O and he cooks some good nascar fries on sat night lol. Where do you live exactlY? I would love to check out your car

[randy]

Did you get my PM? Its $50 per hr. Rodney is great to work with. If you run out of money he will hold on to the car for you as long as you like. The work is by far the best ive seen too. O and he cooks some good nascar fries on sat night lol. Where do you live exactlY? I would love to check out your car
I stole this picture from another member and added some flavor to it. I added rs headlights, cowl hood, tinted windows, front and rear spoiler, and black stripes
http://i30.photobucket.com/albums/c302/icemanrld19/aad41f3a.jpg

Car is sitting on the ground now. Only sheet metal left is the roof. DSE quadralink is installed. Really debating about what to do to the front end. My subframe needs some work and i really dont have 7k to blow on a dse front end right now. This project added up quick lol

[randy]

IM sure ive already posted some of these pictures
Guess its time for a update.

DSE quadralink and ford 9" installed.
http://i30.photobucket.com/albums/c302/icemanrld19/8a66da45.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/e7d41c4b.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/ebf648f7.jpg

DSE subframe connectors installed
http://i30.photobucket.com/albums/c302/icemanrld19/aab67685.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3008.jpg
Tires are here
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1038.jpg

rear quarters, roof, complete floor, firewall, and alot of other sheet metal replaced
http://i30.photobucket.com/albums/c302/icemanrld19/81959184.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/051ef0be.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/2c57bdb4.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/dc0b33ff.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/fcde6670.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/7ad15be8.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/15fc67d3.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/8a6b3331.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/cff8862a.jpg

IM sure there are a ton of other things im missing

[randy]

Time to buy some new parts to move on. What is the best narrowed fuel tank for my ls2 setup and why?

Im also looking for billet tails and a billet gas cap and hopefully i can buy it all in the same place.

[72Z/28]

Time to buy some new parts to move on. What is the best narrowed fuel tank for my ls2 setup and why?

Im also looking for billet tails and a billet gas cap and hopefully i can buy it all in the same place.

Excellent progress man. Have you considered DSE narrowed tank. Also most of the guys here in lateral-g install Ricks tank.

[randy]

Excellent progress man. Have you considered DSE narrowed tank. Also most of the guys here in lateral-g install Ricks tank.

dse is $1150. My builder said he had some problems before with the ricks tanks.

[randy]

I want this tucked look. Is this possible with the stock front subframe? Can it be done with 18" rims all the way around or do i need to go 19s or 20s?
http://i30.photobucket.com/albums/c302/icemanrld19/dp8.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/dp5.jpg

[randy]

Man i really need to update this. Tuesday ill post some latest pictures of it. Car is pretty much ready for paint. Im just trying to make sure its done right the first time around. Man this cost alot more money than i thought but the cars sheet metal and body will be perfect.

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/dsesubframe.jpg

Sorry guys i havent been on in a long time. Body wise the car is ready to go. Just needs paint. I just ordered this subframe yesterday. unfortunately this took a huge chuck of change and progress will be going much slower now. Not to mention my wife told me 3 weeks ago we are expecting out first child.

another thing i just bought was my tank http://i30.photobucket.com/albums/c302/icemanrld19/NewRicksVaporWorxTank.jpg


new camaro fuel pump, notched corners, and good for plenty of HP

[randy]

Will post pictures whenever i get all of my goodies instead of internet pictures. THank you matt at MCB.

Im going to have to hold off for awhile buying any major parts since i just spent alot and we have a child on the way. I plan on bringing the car back to my house so i can work on it myself. Major body work is done. My question is we still have to prime it, paint it and assemble and i need progress to go much slower now so i can save money. At what point sould i have my builder get the car too so that i can start putting parts on whenever i have extra time and money? Should i have him just prime it, paint underneath and the firewall, or what? I dont really want him painting the door jams or the firewall until i completely put the car together so that i know for sure that everything that i want to add is done and fits. I dont want any cutting on any areas already painted.

Im just looking for some overall advice.

[John510]

I want this tucked look. Is this possible with the stock front subframe? Can it be done with 18" rims all the way around or do i need to go 19s or 20s?
http://i30.photobucket.com/albums/c302/icemanrld19/dp8.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/dp5.jpg

I have 19s and with my car super low the tire rubs. 20s would definitely rub

[randy]

im 90% sticking with 18's.

[Sandbagger]

I have 19s and with my car super low the tire rubs. 20s would definitely rub

.....

[WicKeD_SS]

First off, congats on soon to be baby! I just had one 6 months ago and love every min of it!

I hope I can get that sub frame some time soon! Grats on both :thumbsup:

[John510]

im 90% sticking with 18's.

Check page 14 or 15 of my project thread and you can see how my 19" wheel is barely fitting. The car has to be raised to be driven.

If I had to do it again I would do 18 since I like my car LOW

[randy]

Check page 14 or 15 of my project thread and you can see how my 19" wheel is barely fitting. The car has to be raised to be driven.

If I had to do it again I would do 18 since I like my car LOW

Yup i want my car real low too. The lowest i can get it. The rear is going to be 18x12 and i know i can fit a 18x10 in the front but im wondering if that would be the best setup for my car. Either a 18x10 with 275/35/18 or 18x9 with 255/40/18

[John510]

I did a 9 in the front so it would tuck. I don't have my fender on yet so I couldn't tell ya how much clearance I have.

[randy]

Thats to MCB new goodies showed up today. Talk about great craftsmanship
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0010.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0009.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0008.jpg

[waynieZ]

Those are definitely sweet!

[Firehawk_McLeod]

I love them! I have a 68 but im going with 67s for a cleaner look. How much did you set you back?

[randy]

$480. Well well worth it

[Firehawk_McLeod]

$480. Well well worth it

Um yeah.... i think im going to order them now, and have them ready for when my car is done lol. I have sequential tailights already waiting? Do you have the link so i can order them?

[KSBRKTRACER]

What brand are the taillights and are they polished or chromed ? They look very nice.

[MCB Matt]

the tail lights look great!
Keep in mind the great price of the tail lights is with a purchase of a DSE frame and a vaporworks gas tank.. :D

[randy]

the tail lights look great!
Keep in mind the great price of the tail lights is with a purchase of a DSE frame and a vaporworks gas tank.. :D

o yea i forgot. I guess you do get alittle discount when you spend 10,000 worth of other stuff lol

[colin204]

Any updates?

[randy]

i will have some new pic this week. Headers just arrived and im still looking for a local deal on a motor and t56. No luck there yet. The car is currently being pushed around using some 3 series bmw wheels lol.

[MCB Matt]

Have you checked with daytonayellaz? His name is travis, even though not local his $$ are very fair and he KNOWS LS very well! Super nice guy too!

Matt

[randy]

Have you checked with daytonayellaz? His name is travis, even though not local his $$ are very fair and he KNOWS LS very well! Super nice guy too!

Matt

yea im just alittle nervous about something i cant see. takes awhile to gain my trust but when you do i buy buy buy. you know that lol.

I guess i just need to call him up

[Ron in SoCal]

He's a good dude Randy. Pretty busy these days, but will get you a good motor.

[MCB Matt]

Yea, if you check around here on the forum he is a good honest guy...

I never refer anyone unless they have earned my trust as well!

Good luck with your search!

Matt

[randy]

new headers
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0188_zps93b10e41.jpg

ricks gastank with ctsv fuel pump
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0187_zps8483db9e.jpg

small shot of the mini tub
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0186_zpsb929ad4f.jpg

subframe connectors. Anyone know of a better way of attaching the dse subframe connectors to the dse subframe? the dse subframe is rigged at the end. I have a few ideas
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0185_zps671ca6f9.jpg

body gaps
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0184_zps245db620.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0182_zps2e0d4a71.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0181_zps1284ce84.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0180_zpse53a2177.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0177_zpsb13620a0.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0176_zpsaa7277dc.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0175_zps591664aa.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0174_zps14697cb4.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0173_zpsd9523d26.jpg

[randy]

rear quadralink
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0178_zps6b15fd02.jpg

front subframe with the firewall smooth as butter
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0183_zpsf4b1b2f7.jpg

rock solid floor
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0179_zpsd27cbdf9.jpg

[Z10ROD]

we have color books ? we can also call the paint store and get a book with all choices in your color family kinda orange/yellow ? hey by the way i like your project page.
:cheers:

[randy]

we have color books ? we can also call the paint store and get a book with all choices in your color family kinda orange/yellow ? hey by the way i like your project page.
:cheers:

ill come see you weds. I think im ready to order my rims. Dont want to have to "mod" a fender if i need more clearance if the fender is freshly painted
so http://i30.photobucket.com/albums/c302/icemanrld19/zx3p.jpg

or the zx3r version? Obviously without the porshe logo

[randy]

ok im hearing all sort of different stories. DSE is saying to run a 18x9 and 18x11 with the dse subframe and dse quadralink deep mini tubbed but im seeing people on here running 18x10 and 18x12. Honestly what is the best setup? Im looking to have the car running as low also. Rolling the fenders or cutting the inner fenders on the front isnt a problem. I can do it now since i havent started painting it. which can i get a better flushed tuck look? looking to order rims within a week or so


So 18x10 275/35/18 what offset?
18x12 335/40/18 what offset?


OR

18x9 what tire and offset?
18x11 315/30/18 what offset?

rear end :

ford 9" custom alloy axle shafts
21 spline axles
torino flange/press on bearings
axle flange OD 6.9" or less
1/2"-20x 3.00" studs press in
GM 5 of 4 3/4 bolt circle
1/2" pinion offset
access hole to axle flange
Truetrack 31 spline differential
"f" measurement 25.375?"
"g" measurement 24.375"
Total axle width 54/750 axle flange to axle flange
rear brake line tab
pair rear axle seals
moser 9" ford complete 3rd member
n-case
daytona aluminum pinion support
1250 yoke w/u-bolt
4.11 gear ratio
powdercoated gloss black

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/F5597358.jpg


Whos car is this and what color? almost looks like bad penny but more orange and brighter

[badmatt]

Looks like atomic orange.

http://i170.photobucket.com/albums/u275/FartpipeZ06/2008%20C6Z06/P1030741-1.jpg

[WicKeD_SS]

http://i30.photobucket.com/albums/c302/icemanrld19/F5597358.jpg


Whos car is this and what color? almost looks like bad penny but more orange and brighter

That is penny before it was turned into the beast she is today. http://www.lateral-g.org/rupp/

[XLexusTech]

so what do you go with?

ok im hearing all sort of different stories. DSE is saying to run a 18x9 and 18x11 with the dse subframe and dse quadralink deep mini tubbed but im seeing people on here running 18x10 and 18x12. Honestly what is the best setup? Im looking to have the car running as low also. Rolling the fenders or cutting the inner fenders on the front isnt a problem. I can do it now since i havent started painting it. which can i get a better flushed tuck look? looking to order rims within a week or so


So 18x10 275/35/18 what offset?
18x12 335/40/18 what offset?


OR

18x9 what tire and offset?
18x11 315/30/18 what offset?

rear end :

ford 9" custom alloy axle shafts
21 spline axles
torino flange/press on bearings
axle flange OD 6.9" or less
1/2"-20x 3.00" studs press in
GM 5 of 4 3/4 bolt circle
1/2" pinion offset
access hole to axle flange
Truetrack 31 spline differential
"f" measurement 25.375?"
"g" measurement 24.375"
Total axle width 54/750 axle flange to axle flange
rear brake line tab
pair rear axle seals
moser 9" ford complete 3rd member
n-case
daytona aluminum pinion support
1250 yoke w/u-bolt
4.11 gear ratio
powdercoated gloss black

[randy]

That is penny before it was turned into the beast she is today. http://www.lateral-g.org/rupp/

wow i couldnt tell. In the newer pic the car looks more cooper/bronze. It was repainted the same color?

[randy]

so what do you go with?
GA3 step lip
Polished outer rim
titanium center and inner
titanium engraved center cap
hidden hardware
18x9.5 6.375" offset 275/35/18
18x11.5 5" offset 315/30/18
http://www.kore3.com/downloads/fitment_templates/DOC0019.pdf
http://www.kore3.com/downloads/fitment_templates/DOC0020.pdf

Waiting to hear back from kim at matts classic bowties. trying to order today

[badmatt]

After a few minures of searching its a Chrysler prowler color

[randy]

After a few minures of searching its a Chrysler prowler color

yup. i already got the paint code and added alittle flavor to it. I would post a test panel but na. :) Cant wait to get my forgelines.

[randy]

So what about adding something like this?

oviously not painting the mesh
http://i30.photobucket.com/albums/c302/icemanrld19/hoodvents.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/hoodvent.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/gallery12.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/488200_434819846563421_1165591366_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/304853_434819156563490_1007698828_n.jpg

[randy]

some POR15 love. getting close to paint.

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0215.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0216.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0217.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0218.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0219.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0220.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0221.jpg

[randy]

sorta combining bmw valencia orange and prowler orange.

we have a hint of color
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1113.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1112.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1111.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1110.jpg

[settintrendz]

color looks good!

[Z10ROD]

yea dam nice choice:thumbsup:

[randy]

some new goods today. OMG the stock rotors are heavy. I will deff upgrade in the future.

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0227.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0228.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0229.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0230.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0231.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0226.jpg

[waynieZ]

Nice addition. Those will definitely stop you.

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1142.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_1141.jpg


now if my rims would just show up :(

[waynieZ]

Looks Good.

[randy]

Pic do not do the wheels justice !!!!

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0255.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0254.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0253.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0252.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0251.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0250.jpg

[randy]

Next im going to slam the car and test for any and all clearance issues. I was told a 18x9.5 wouldnt fit on the front without rubbing. Well my fronts are 18x9.5 with 6.375 backspacing and the front very low there are no rubbing issues ")


http://i30.photobucket.com/albums/c302/icemanrld19/530405_131611773662431_2146543755_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/395022_131611683662440_1183341816_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/196605_133481233475485_1011019400_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/155914_131312370359038_1757503456_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/148208_131611646995777_593451050_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/35671_131611986995743_1148794171_n.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/20699_133481546808787_376372111_n.jpg

[randy]

car is now lowered, rear end is set in the correct location, car is slammed to the ground and no rubbing issues at all. I pulled the front inner fenders just alittle and i have plenty of clearance. I know DSE wants you to run a 18x9 on the front but i went with 18x9.5 at 6.375 backspacing and its PERFECT !!!!
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0266.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0265.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0264.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0263.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0262.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0261.jpg



and i love this pic.

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0260.jpg

[Cole]

Right on. .. That's pretty.

[cencalc6]

Very Nice Job!:thumbsup:

[Jgpclone]

Love the color very nice coming along great

[KPC67]

looks great, what did you do to your inner fenders?

[randy]

looks great, what did you do to your inner fenders?

not a lot. I just bolted up the inner fenders and grabbed the corner by the control arm and tugged on it some. I ended up pulling it even with the control arm bolt. I now have atleast a 1/4 clearance at the closes point between the tire and fender.

[Sonar Chief]

That's an awesome color choice :thumbsup: :thumbsup: Looking great!

[makoshark]

WOW! Car is looking great! Not much longer before you'll be driving this beauty.

[randy]

I have my rear coilovers pretty much slammed. Almost to the point im really close to the bump stops. I might cut the bump stop in half but i was wondering if dse makes shorter coilovers? The thread part of the coilover is just alittle long for my liking.

[Frankenstine]

super nice build:thumbsup: ? for ya, will you have any issues with the paint not matching because of the way you are doing it. not hating just currious:thumbsup:

[randy]

no. car is only jambed. proper way to paint is to jamb the car and reassemble. Paint all the panels on the car at the same time.

I thought the same thing at first but after seeing his work however he wants to paint it im fine with it. this car is the reason i chose him
http://i30.photobucket.com/albums/c302/icemanrld19/1d6705f6.jpg

and this is his cuda. I used it for my engagement pics
http://i30.photobucket.com/albums/c302/icemanrld19/Randy_Cristin_Engagements_057.jpg


recently completed
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0841.jpg

[Frankenstine]

Thanks for the Info:thumbsup:

[Z10ROD]

PRO-TOUR 58 Impala bad ass:thumbsup:

[randy]

Cleaning up all the nasty window trim pieces. Trying to get all the old glue and old overspray off of them. I will then paint or powder coat them black. Just havent decided on glossy or not
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0271.jpg

New pic before clear
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0143.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0144.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0145.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0146.jpg


and now with some clear
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0147.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0148.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0149.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_0150.jpg

[Z10ROD]

I have the 58 Impala is House of color PAVO Purple it covers good and the glass company scratched the crap out ouf it and I had to repair matched very well just re shot the cowl and I couldn't tell otherwise I would have blended the hood and fenders

Car looks good Randy I like the color choice.

[214Chevy]

and this is his cuda. I used it for my engagement pics
http://i30.photobucket.com/albums/c302/icemanrld19/Randy_Cristin_Engagements_057.jpg




Sorry, but I don't see a Cuda in this pic....where? Just kidding bro, the Cuda is nice and you have a beautiful young lady there as well. I mean that with the utmost respect.

[randy]

ride height is just about right :) Car has yet to be color sanded and buffed. Cant wait to see it shine then

http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3925.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3923.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3922.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3921.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3920.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3919.jpg

[waynieZ]

Beautiful color. It looks great.

[Jgpclone]

sweet color :thumbsup:

[John510]

I love that shade of orange.

[randy]

some pic in the sun :) soon the car will be color sanded, buffed and some parts will go back on
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0340.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0339.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0338.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0337.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0336.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0335.jpg

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0334.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0333.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0332.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0331.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0329.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0328.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0327.jpg

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0326.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0325.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0324.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0323.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0321.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0320.jpg

[randy]

and engine is trans is mocked up on my buddies 69 dse subframe
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0317.jpg

its close so we are going to have to tilt the engine up some or mod the crossmember. chances are the crossmember will get flattened out.
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0316.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0315.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0312.jpg

the adapter will need to be turned the other way. currently its touching the headers
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0311.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0310.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_3924.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0307.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0306.jpg
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0305.jpg

Overall the SW header clearance is amazing. they fit perfect in the subframe.

[Ron in SoCal]

:cheers: :D

[intocarss]

:thumbsup: :thumbsup: :thumbsup:

[Richio1]

Love the color... beautiful!:D

[sds machining]

Looking really nice,, :thumbsup:

[michaelh440]

Just awesome. I'm in the tear down stage with my 67 and looking for a shop to do the metal work. I'm in the metroplex and would love to see you car and pick our brain about shops in the area and your experiences.

[Todd in vancouver]

That car looks AWESOME! What an incredible package you have built, very nice work.

Just a question for you , in the above picture from the back of the car.does the guy in the picture know you posted it with him digging for boogers? :lol:

[KPC67]

coming together very nicely :thumbsup:

[Z10ROD]

I do now Todd and yes I found one you want body shop dust sucks

[chr2002ca]

Awesome project. Great color combo. Congrats on the progress. :thumbsup: :cheers:

[parsonsj]

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0305.jpg

Where did you get that crossmember? I'm looking for something similar...

thanks!

[randy]

from hurst driveline

[KPC67]

^^^ hurst driveline I believe makes that cross member if memory serves??

(edit) beat me to it Randy

[parsonsj]

Well, that sucks. :( H-d only sells kits, not components. I'll keep looking. Sorry for the thread diversion.

[randy]

Talk it up. More info the better. Give them a call they might help you

[randy]

switched to a speedtech adjustable crossmember. Perfect clearance with the floor and headers. Much better

Does anyone know if a lm7 engine will work for a mock up? I have yet to purchase my engine/trans due to the wife wanting to buy a house lol. A friend is giving me his lm7 engine and im wondering if the outside of the block is the same, motor mounts will work, ls3 front drive accessory, and intake will all atleast bolt onto it so i can wait till i get a killer deal on a ls3/t56

What does everyone use to spray inside the doors or rush preventative and sound deadening? Im going to use dynamat for everything else but what about all the hard reach areas?

[randy]

Any difference swapping a ls3 from a corvette or a ls3 from a camaro? I remember before there was something about a different 24 or 58 reluctor?

[GrabberGT]

I dont know why, but I half expected to see this thing at GG this spring. Lets get it movin. You've got just over 4 months to the next event. :hairpullout:

[Ron in SoCal]

Any difference swapping a ls3 from a corvette or a ls3 from a camaro? I remember before there was something about a different 24 or 58 reluctor?

Nope. Gen IV LS3 Engines are the same and 58x (DBW). Transmissions would be different though.

[randy]

Nope. Gen IV LS3 Engines are the same and 58x (DBW). Transmissions would be different though.

Thank you. Im going to make a call tomorrow. Everything goes right i should have a nice ls3 for 4500

[randy]

I just bought two packs of http://www.bestbuy.com/site/Dynamat+-+Xtreme+18%22+x+32%22+Sound-Dampening+Sheets+(9-Pack)/2902831.p?id=1218361849719&skuId=2902831&st=dynamat%20xtreme&cp=1&lp= Normally $180 on sale for $127. THis should do my entire car. I will use b-quite on some other areas. So happy to start putting the car back together.

Its going to be busy the next few weeks. We just got a offer on our house and it should be sold, we are also going to maui on the 10th, and piecing the car together

[randy]

Gathering info for stud change.

http://i30.photobucket.com/albums/c302/icemanrld19/corvettefrontstud.jpg (http://s30.photobucket.com/user/icemanrld19/media/corvettefrontstud.jpg.html) Corvette front hub stud

Wheel Bolt Knurl Dia. : 12.73 mm
Wheel Bolt Overall Length : 41.5 mm
Wheel Bolt Shoulder Length : 8 mm
Wheel Bolt Thread Size : M12-1.5
Wheel Bolt Threads : Right Hand
Wheel Bolt Head Marks : 254

What stud is used on the ford 9" quadralink rear axles? I know its a 1/2 thread pitch. Im thinking about installing the same studs in my front corvette hubs

[Ron in SoCal]

1/2x20 I believe

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0390.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0390.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0389.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0389.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0388.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0388.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0387.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0387.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0385.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0385.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0384.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0384.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0383.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0383.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0382.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0382.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0381.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMAG0381.jpg.html)

[GrabberGT]

Thats a really awesome color. I had to go back a couple pages to check my memory. I thought this car was orange.

[randy]

next up is

Install middle bumper bracket
Install license plate lamp
Install spoiler
add hardlines to exit towards the front on the gas tank
Install gas tank filler neck
Install flexable fuel lines from frame to fuel tank
INstall hard fuel lines from flex lines to under the hood to the regulator


After that i will attack the side glass, door handles, mirrors, locks

[randy]

Thats a really awesome color. I had to go back a couple pages to check my memory. I thought this car was orange.

it actually is in a way. Today we had a overcast so the car is more red. more orange when theres direct sunlight

see
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0327.jpg

[XLexusTech]

Gorgeous.. congrats

[waynieZ]

That is a beautiful color. The car looks SWEET !

[Ron in SoCal]

Gorgeous.. congrats

That is a beautiful color. The car looks SWEET !

So pretty Randy. Congrats man! :cheers:

[Richio1]

Yeah very nice. I bet it is even nicer in person... seeing it up close in the sun.

[Rick D]

Wow that looks great Randy, it really pops in the sun!

[GrabberGT]

it actually is in a way. Today we had a overcast so the car is more red. more orange when theres direct sunlight

see
http://i30.photobucket.com/albums/c302/icemanrld19/IMAG0327.jpg

I cant wait to see this car in person. I'll have to look up the shop address one day and come see it.

[tubbed69]

great job on this Randy,that color is beautiful outside,stance is perfect

[randy]

we moved into a new house a couple weeks ago and im bringing the car home for alittle then back to the shop to finish it up.

Past couple days we have installed the quarter windows, door glass, wing window, the the trim with the windows mentioned, front spoiler mounted up, mocked up the front calipers, spoiler and narrowed the seats down for the quadralink and mini tub.

Next up this week before it comes home is to install door panels, mock up gauges, turn signal lenses, align front bucket headlights, door locks, and and dynamat the doors
http://i30.photobucket.com/albums/c302/icemanrld19/1006057_10100164972990086_1175886782_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/1006057_10100164972990086_1175886782_n.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/945817_10100164972830406_7961523_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/945817_10100164972830406_7961523_n.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/1173726_10100164972895276_1142726437_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/1173726_10100164972895276_1142726437_n.jpg.html)

http://i30.photobucket.com/albums/c302/icemanrld19/484042_10100164973039986_1450923705_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/484042_10100164973039986_1450923705_n.jpg.html)

[Ron in SoCal]

Was just thinking about your project today Randy. Please post more updates when you can...:)

[randy]

thanks man.

Im thinking the red on the calipers might have to go eventually. I cant wait to post pic of my windows once they are tinted. Blacking out all the chrome pieces there really changed the look of the car.

since we bought a new house things are going slowwwwwwww.

[randy]

heres an idea on how the trim around the window painted black looks. I love it. Im not sure how well it will withstand scratches but ill deal with that later

Shes finally home for alittle bit.

http://i30.photobucket.com/albums/c302/icemanrld19/1185918_10152015488967741_749117612_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/1185918_10152015488967741_749117612_n.jpg.html)

[Sonar Chief]

heres an idea on how the trim around the window painted black looks. I love it. Im not sure how well it will withstand scratches but ill deal with that later

Shes finally home for alittle bit.

http://i30.photobucket.com/albums/c302/icemanrld19/1185918_10152015488967741_749117612_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/1185918_10152015488967741_749117612_n.jpg.html)

Man that car is perfect, nice stance .... looks good w/ blacked out trim :hail::hail:

[randy]

i like the way it looks without mirrors but i think it will be smart to add them. :Tomcat:

[214Chevy]

That color pops in the sunlight.:hail:

Besides...I thought you said....... LOL!! Just kidding.

THis is exactly how i want my 67
http://i30.photobucket.com/albums/c302/icemanrld19/efc7cfa2.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/1d6705f6.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/c6f6b540.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/86036004.jpghttp://i30.photobucket.com/albums/c302/icemanrld19/4be6c498.jpg

[randy]

dynaliner installed on the panel. The inside of the door is dynamated. I used one sheet for the door. I didnt feel the need to cover the entire inside of the door. Dynamat is a vibration dampener so this should do. You can tell a difference already just knocking on the door


http://i30.photobucket.com/albums/c302/icemanrld19/dynaliner.jpg (http://s30.photobucket.com/user/icemanrld19/media/dynaliner.jpg.html)

http://i30.photobucket.com/albums/c302/icemanrld19/1185325_10100173664686856_524887443_n.jpg (http://s30.photobucket.com/user/icemanrld19/media/1185325_10100173664686856_524887443_n.jpg.html)

[Ron in SoCal]

S0UvJZmGTsk

:thumbsup: :thumbsup: :thumbsup:

[tubbed69]

Randy cars looks great,I have not forgot the pics of the ebrake routing you asked for from my build,I will have some in the next few days,again your car is absolutely awesome

[randy]

Randy cars looks great,I have not forgot the pics of the ebrake routing you asked for from my build,I will have some in the next few days,again your car is absolutely awesome

thank you. Now since its home i get to work on it more and more :)

Heres a short video of the dynamat door Vs non dynamat fender. Its hard to tell in the video but in person OMG there is a huge difference. As far as the dynamat goes i did not cover the entire inside of the door. I cut each sheet in 4" strips and installed it that way leaving a little gap between each sheet. I was able to use one sheet of dynamat per door even adding some on the sides and the front of the door.
http://i30.photobucket.com/albums/c302/icemanrld19/th_20130827_204701.jpg (http://i30.photobucket.com/albums/c302/icemanrld19/20130827_204701.mp4)

[randy]

Need help with mirror options. I found this on a miata forum

A few weeks ago I was bidding on a pair of rare Garage 502 NB mirrors that popped up on Yahoo Japan Auctions but got outbid fairly quickly. I love the simple design of those mirrors unlike the APR mirrors we always see that require an adapter base. I actually bought a set of SlickAuto APR mirrors the day they first got released and I never thought they matched the car well. I ended up selling them a few months later.

I've always seen Garage Vary cars rock these motorcycle mirrors and since then I've been wanting to do the same on mine.


http://i454.photobucket.com/albums/qq266/frivera2121/EEDD0A9B-E482-4285-BBDF-5E3189ABBEB7-3042-0000039F9A012168_zps691a5771.jpg

Murakami Motors sells a set similar to those but with a price tag close to $500. Being on a budget I decided to try my luck on finding a used set of Magical Racing mirrors from a motorcycle forum. Sure, enough my patience paid off and I found a decent set for a decent price.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_32241022x_zps19e7e0b2.jpg

They had type 1 mirrors with type A bases with an elbow and a 45mm stem....everything I needed.

Next came the SlickAuto Miata bases. You can purchase just the Miata APR mirror adapter kit separately without the mirrors for $90.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_34819252x_zps93271292.jpg

SlickAuto mirrors bases comes with two smaller holes for the mounting of the APR mirror base. I decided to use the threaded hole closest to the driver to mount the Magical racing mirror. The same way the Garage 502 mirrors are off center so they can be clearly seen and not blocked by the triangle pillar on the window.

You can use the magical racing mirror base and mount it on the SlickAuto miata bases but I really hate the way they look stacked on top of each other. I wanted a cleaner look so I went the extra mile.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_49909602x_zpsb1cf2532.jpg

10 mm hole is needed for the Magical Racing stems. The underside of that same hole needs a countersunk hole. 1/2" countersink drill bit took care of that.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_92826732x_zpsf48c6b9f.jpg

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_58839782x_zpsf65acca5.jpg

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_9867862x_zpsdb06c04c.jpg

For the extra small threaded hole I purchased 3.5 mm stereo jack silicone plugs to cover the hole. It's a bit loose so glue will be needed to stay put.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_8329402x_zpsc348d81b.jpg

Assembled and ready to be mounted.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_39877872x_zpsc707aa55.jpg

Test fit and mirror adjustments before tightening it all down. Right now I'm using the hardware SlickAuto provides in their kit but I plan on replacing those two stainless bolts with black aluminum anodized ones.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_95447762x_zpsad695f2c.jpg

Good view on the passenger side... Pillar barely gets in the way thanks to the off center mount of the stems.

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_87914212x_zps3f648c40.jpg

Exterior shots....

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_19417602x_zps774d21d2.jpg

http://i454.photobucket.com/albums/qq266/frivera2121/Camera%20Awesome%20Photos/preview_image_1_11380622x_zps1bd870b6.jpg

[randy]

mirrors must be paintable. I really like the 68 mirrors but i cant see painting them and holding up. These are similar but smaller. Maybe put the 68 base and use these mirrors?

[randy]

To Do list. Sorry just trying to get a gameplan. Everyone else can ignore this
:twak:



1. :bigun2:
Dynaline headliner
Install headliner and light
Dynamat sail panel area
Dynaline sail panels
install sail panels
Install visors
get rear seats to match the front seats


2. :bigun2:
Drill holes for mirror drivers side mirror
Seam seal drivers side inner door?
apply more dynamat if needed
Readjust drivers side door window molding
Install lower door molding to panel in the drivers side
Install drivers side door panel for the final time with all hardware
Install drivers side new door molding

3. :bigun2:
Drill holes for mirror passanger side mirror
apply more dynamat if need
Seam seal passanger side inner door?
Readjust passanger side door window molding
Install lower door molding to panel in the passanger side
Install passanger side door panel for the final time with all hardware
Install passanger side new door molding

4.
run rear wiring harness

5.
Dynamat rear carpet area
Dynaline rea carpet area.
Install rear carpet

6.
Seam seal drivers side rear quarter panel to wheel well area?
Readjust drivers side rear quarter panel window molding
Install drivers side rear panel and hardware for the final time

7.
Seam seal passanger side rear quarter panel to wheel well area?
Readjust passanger side rear quarter panel window molding
Install passanager side rear panel and hardware for the final time

8.
Dynamat rear package tray and backseat portion
Dynaliner package tray cover
Install rear 6x9. cut if needed
Install Package tray cover
Install back part of the backseat
Install lower part of the backseat

9.
Install engine/trans
Raise transmission tunnel if needed

10.
Seam seal drivers side kick panel area
Dynamat drivers side kick panel area
Seam seal dash to firewall area drivers side

11.
Seam seal passanger side kick panel area
Dynamat drivers side kick panel area
Seam seal dash to firewall area passanger side

12.
Dynamat the rest of the floor and firewall
Dynaline the rest of the floor and firewall
Install front carpet
Install front seats

13.
Run fuel lines

14.
Remove front seats
Install dash wiring
Install vintage air

15.
install headlight bulbs
center headlights

16.
clear coat by the drip rail on the passanger side
scratch by the hood latch
possibly paint the firewall black


:hello: :willy: :happy23:

[Sonar Chief]

Randy .... not feeling those Miata mirrors! Somewhere in this forum 71-72 GTO mirrors used on first gen Camaro's looked kick a**, I did write down the store .... Ames performance.

Hope that helps! Good luck with your list :thumbsup:

[randy]

one thing i noticed is if its dark in my garage and a shine a light under the tulip panel some light comes thru. Should there be any light coming thru that area to where you can see inside the cabin kick panel area?

[Sonar Chief]

one thing i noticed is if its dark in my garage and a shine a light under the tulip panel some light comes thru. Should there be any light coming thru that area to where you can see inside the cabin kick panel area?

WOW :waveflag: med check! Randy, I thought we were talking about the mirrors?

What the halibut are you talking about?

[randy]

well the answer is YES. lol. The tulip panel is the lower side panel on the firewall. When doing a vintage air kit they give you a block off plate. Well that block off plate covers the round hole on the tulip panel. Water is suppose to run inside the tulip panel and come out where the fender and rocker panel meet.

[Sonar Chief]

well the answer is YES. lol. The tulip panel is the lower side panel on the firewall. When doing a vintage air kit they give you a block off plate. Well that block off plate covers the round hole on the tulip panel. Water is suppose to run inside the tulip panel and come out where the fender and rocker panel meet.

OK ..... the block off plate is for the blower motor correct? The bottom of the outer cowl is supposed to let water and debris run out of the upper cowl and off the side cowls and out the bottom of the car just in front of the rocker. However the front fender usually collects most of the waste and that's why it rusts out.

You need to lay some serious 3M seam sealer inside that side cowl panel, and when you put in your kick panels use the same plumbers putty that the factory used or equivalent to seal the moisture from the carpet and underlayment.

[randy]

yup my thought exactly. Either way the car wont see rain but i just wanted to make sure. Thank you.

stole your pic but the light comes from the very bottom of the tulip panel.
http://imageshack.com/a/img28/9853/1303161866.jpg (http://imageshack.com/i/0s1303161866j)Uploaded with ImageShack.com (http://imageshack.com)
I need to find seats now !!!! :computer:

[randy]

So i went to install my windlace end caps. How does the metal flat tab install go? Is there suppose to be a hose to where i screw the cap in?

[randy]

figured it out. The tab just goes behind the ujamb molding. Now my quarter window molding is also there. Im thinking about running a screw into the quarter molding felt that also goes into the windlace end cap to keep it more secure.

I also installed the backseat divider with pading. there was some discussion if the pad side or the board side faces the trunk. Well im using the board size facing the trunk so my pading touches my backseat metal frame. Im then going to dynaline the board side with 1/8 dynaliner since it looks sexy :)

[Firebird-Geek]

Randy,

Awesome build! :cheers: Love the color!

Question:

I see early in the thread you said you had your tires: BFG 335/30-18's. But I now see your car is sporting some Michelin tires. Is there a reason you changed?

I have a 67 Firebird I am doing right now... and am in the tire/wheel dilemma of choosing.
Thinking:
18x9 front 18x12 back
or
18x9 front 19x11.5 back

I kind of wanted to run 19's in the back for a bit more ground clearance. (Not such good roads and driveways here in SD) Do you feel you have an OK amount of ground clearance with what you choose? Any rubbing issues?

Thanks,

[randy]

Randy,

Awesome build! :cheers: Love the color!

Question:

I see early in the thread you said you had your tires: BFG 335/30-18's. But I now see your car is sporting some Michelin tires. Is there a reason you changed?

I have a 67 Firebird I am doing right now... and am in the tire/wheel dilemma of choosing.
Thinking:
18x9 front 18x12 back
or
18x9 front 19x11.5 back

I kind of wanted to run 19's in the back for a bit more ground clearance. (Not such good roads and driveways here in SD) Do you feel you have an OK amount of ground clearance with what you choose? Any rubbing issues?

Thanks,
ground clearance will be plenty fine. 275/35 and 315/30 aspect ratio was spot on. Also the 335 might touch if i really slam the car down. I wanted alittle extra clearance. The 335 bfg run bigger than most 335 tires and they are getting harder to find. Get the 11.5 wheel so you can put either 335 or 315s on. Im very very happy with a 11" wheel and 315s. The tire specs are a perfect match

[frankv11]

Just went through your build , you moved along pretty fast. Very nice work!
Especially like the picture in paint booth before the clear.

[manelasj]

Randy, Great Build! I have the same project going on. Can you tell me more about the header fitment? I have the DSE front subframe, the DSE engine mounts to locate in the stock position. Did you have to modify anything to get those headers to fit? Until I saw your build I didn't find any headers that worked for this combo. Which mounts did you use? Thanks for the help.

John

[randy]

Randy, Great Build! I have the same project going on. Can you tell me more about the header fitment? I have the DSE front subframe, the DSE engine mounts to locate in the stock position. Did you have to modify anything to get those headers to fit? Until I saw your build I didn't find any headers that worked for this combo. Which mounts did you use? Thanks for the help.

John

let me pull out my ticket for the headers so i have all the part numbers. Nothing had to be modified. They fit great. I think they are the best headers for the money. I would have liked to have the dse ones because they are meant for the car and fit the best buy couldnt justify the cost right now. Headers hang maybe a inch below the subframe.


DSE header fitment ( not my car )
http://i1015.photobucket.com/albums/af278/jcgrestoration/IMG_0664.jpg

http://i1015.photobucket.com/albums/af278/jcgrestoration/IMG_0665.jpg

[randy]

need some help.

So i have the passanger side windows to my liking. The problem is the drivers side wing window. I think it sits alittle too low. There is a screw on the inside of the door, bolt on the top right, and bolt on the side if you are looking at it. Now i can take the screw out and pull the window up and tighten the bolts to where i like it but i cant get the screw back in. So i tried the opposite first. Install the screw and then pull the window up. Problem is i cant seem to get enough adjustment this way like i did with the screw out.

Does anyone have a picture or a idea what this screw actually does? I can start the screw but it doesnt seem to go in the correct path. Any help would be great

[Sonar Chief]

To Do list. Sorry just trying to get a gameplan. Everyone else can ignore this
:twak:



1. :bigun2:
Dynaline headliner
Install headliner and light
Dynamat sail panel area
Dynaline sail panels
install sail panels
Install visors
get rear seats to match the front seats


2. :bigun2:
Drill holes for mirror drivers side mirror
Seam seal drivers side inner door?
apply more dynamat if needed
Readjust drivers side door window molding
Install lower door molding to panel in the drivers side
Install drivers side door panel for the final time with all hardware
Install drivers side new door molding

3. :bigun2:
Drill holes for mirror passanger side mirror
apply more dynamat if need
Seam seal passanger side inner door?
Readjust passanger side door window molding
Install lower door molding to panel in the passanger side
Install passanger side door panel for the final time with all hardware
Install passanger side new door molding

4.
run rear wiring harness

5.
Dynamat rear carpet area
Dynaline rea carpet area.
Install rear carpet

6.
Seam seal drivers side rear quarter panel to wheel well area?
Readjust drivers side rear quarter panel window molding
Install drivers side rear panel and hardware for the final time

7.
Seam seal passanger side rear quarter panel to wheel well area?
Readjust passanger side rear quarter panel window molding
Install passanager side rear panel and hardware for the final time

8.
Dynamat rear package tray and backseat portion
Dynaliner package tray cover
Install rear 6x9. cut if needed
Install Package tray cover
Install back part of the backseat
Install lower part of the backseat

9.
Install engine/trans
Raise transmission tunnel if needed

10.
Seam seal drivers side kick panel area
Dynamat drivers side kick panel area
Seam seal dash to firewall area drivers side

11.
Seam seal passanger side kick panel area
Dynamat drivers side kick panel area
Seam seal dash to firewall area passanger side

12.
Dynamat the rest of the floor and firewall
Dynaline the rest of the floor and firewall
Install front carpet
Install front seats

13.
Run fuel lines

14.
Remove front seats
Install dash wiring
Install vintage air

15.
install headlight bulbs
center headlights

16.
clear coat by the drip rail on the passanger side
scratch by the hood latch
possibly paint the firewall black


:hello: :willy: :happy23:


SO? Where are you on this list? I need updates fer sure ..... hope all is well!!!!

[68Cuda]

SO? Where are you on this list? I need updates fer sure ..... hope all is well!!!!

I think he is somewhere between step 1 and expecting his 2nd child...

[randy]

Parking brake assembly is installed. I wanted to use the most factory parts that i could so i bought a stock parking brake cable kit to use with my c6 brakes. The two rear cables would have been a pain to attach plus they were little long. I managed to open up the hole on the rear brake cable mount to 9/16 and i ordered 1988-1996 corvette rear ebrake cables from oriellys for $20 each using ac delco part number 19143753. These cables are much shorter and fit perfect with my brake kit and quadra link. I will attach pictures but they are not of my car since the car isn't high enough to get pictures. I then used the front cable of my kit and hooked it up to the brake and ran the line thru the subframe. Now here is where i had another problem. The intermediate cable was too short. The correct non big block cable that comes with my car from the factory is 79" long. i need about 3 more inches. Luckily firewheel classics also makes another cable part number pbk-11r for the big block camaro that is 82" long. This will work perfect.. Long store short you want the following :

1988-1995 corvette rear ebrake cables ac delco part number 19143763
67 camaro big block intermediate cable pbk-11r
front cable pbk-10a
Drill out the kore 3 bracket to 9/16"

http://i30.photobucket.com/albums/c302/icemanrld19/rearebrake3.jpg (http://s30.photobucket.com/user/icemanrld19/media/rearebrake3.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/rearebrake2.jpg (http://s30.photobucket.com/user/icemanrld19/media/rearebrake2.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/10868159_10100487126087696_4585624926415633014_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/10868159_10100487126087696_4585624926415633014_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/10846283_10100487131357136_6273500582914268194_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/10846283_10100487131357136_6273500582914268194_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/10846057_10100487131337176_5219923487792039921_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/10846057_10100487131337176_5219923487792039921_n.j pg.html)

[randy]

new softseal door weather stripping is done, rear brake assembly done, rear calipers and pads done, parking brake cables done, parking brake installed, wiper transmission installed and centered, cowl hood installed, gaps are where i want them to be, car is dynolined, panels are dynamated, windows are aligned, rear speakers installed, rear package tray,

Next up is probably doing some wiring. I have everything i need except exhaust, engines/ trans, vintage air, fuel lines, and front seats. Everything else is waiting to be installed

[68Cuda]

Harness and ECU:
http://www.efisource.com/shop/ms3-lsx-plug-and-play/

Works on one of these:
https://www.youtube.com/watch?v=dxVvPkAIP8Q

[tubbed69]

Randy the color,wheels and stance are perfect on this car,good luck on finishing it up:trophy-1302:

[randy]

looking for black morris classics 3 point front seatbelt set that matts classic bowties had a special on. I think they were $299. Hoping they see this and shoot me a PM tonight and Ill shoot them a credit card. If not i might buy some finch products.

[randy]

Exchanged a email. Just waiting to hear back. I have $300 to spend tonight.

[RCC]

I'll take Finch for 300 ?
:y0!:

[randy]

I'll take Finch for 300 ?
:y0!:

nope i bought 3 point seat belts from www.mattsclassicbowties.com . Just waiting on confirmation that they have been ordered. On a side note I need some help deciding on a steering wheel. Should i get a black or polished steering wheel? Im leaning towards black with some polished pieces on it to match the finch billet shifter plate. Maybe something like this http://autoplicity.com/2515374-billet-specialties-blk29263-14-select-edition-steering-wheels?utm_source=Pricegrabber&utm_medium=CSE&utm_content=2515374NOFITMENT&utm_campaign=PricegrabberNOFITMENT

[MCB Matt]

Your order is in and the belts will ship very soon :ups:

Thanks again for the order, this car is turning out BADA$$ :thumbsup:

Matt

[randy]

Your order is in and the belts will ship very soon :ups:

Thanks again for the order, this car is turning out BADA$$ :thumbsup:

Matt

Want to help me with a steering wheel? Im just hoping i win that $200 gift card to buy my corbeau gets II seats, shaved bottoms, and seat rails from you

[MCB Matt]

Sure, I can help with the wheel.

FYI, I literally got an email today that Corbeau is having a "slight" price increase Jan 1st. I will be back in soon, I will check to see what slight is and give you a heads-up.

Matt

[randy]

So theres not much left. Is the DSE battery relocation kit worth it or is there another option? $400 for some wires, bulkheads, and tray seems expensive. What else is everyone doing?


All side trim is completely assembled now.

Phase 1
Install battery relocation kit
Install electrical
Install headlights

Phase 2
Take to www.rodscarcraft.com
Brake lines
Fuel lines
Raise the tunnel
Install headliner
Install vintage air

Phase 3
Bring home
Install seats
Seat belts
Install engine/ trans
Install radiator
Install engine electrical
Install exhaust

[randy]

Opinions?
http://www.crossmembers.com/shop/crossmembers-general-motors-body-nova-ventura-1967-1969-camaro-firebird-crossmember-t56-p-351.html

[randy]

ls3/ 480hp gm ls3

2 1/2 exhaust or 3"?????


I need to update this thread soon.

Lots of work is done

ls3/480hp t56 installed
Fuel and brake lines installed
Fuel lines converted to -6an
Hydroboost with wildwood master cylinder installed. Using a art morrison ( great clearance and much better than wilwoods kit) wilwood proportioning valve kit
Kwik AC bracket with corvette accessories installed
Tunnel is raised using chris alston t56 tunnel
Finch dual vent installed
DSE battery relocation kit and bulk heads installed
Holley t56 crossmember ( fit like ****) modified it and now it works great
Holley black billet fuel rails are on the way. Will be installed this week
Fuel system will be completed and all brake lines this weekend. After that time for wiring and maybe hear it run?????

[MCB Matt]

You might as well go 3" if the cross member will allow. I have heard about quite a few guys not getting along with that cross member! What did you have to do to it to make it work?

Great to see the car finally close to done!!

Matt

[randy]

You might as well go 3" if the cross member will allow. I have heard about quite a few guys not getting along with that cross member! What did you have to do to it to make it work?

Great to see the car finally close to done!!

Matt

Cut a lot out of it. First the crossmember was touching the floor. Only bairly. I had to cut the top down. In order to get to the 3 degree angle i had to cut underneath it exhaust cut outs. The headers were in more than the arches so i had to remove even more metal and offset the crossmember to the right side of the engine. Total PITA.

I still need to learn it up and paint it.
http://i30.photobucket.com/albums/c302/icemanrld19/11099937_10100653525970996_4194664078682039236_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11099937_10100653525970996_4194664078682039236_n.j pg.html)

http://i30.photobucket.com/albums/c302/icemanrld19/11826069_10100653525995946_404240692632503258_n.jp g (http://s30.photobucket.com/user/icemanrld19/media/11826069_10100653525995946_404240692632503258_n.jp g.html)

[paulk68]

Cut a lot out of it. First the crossmember was touching the floor. Only bairly. I had to cut the top down. In order to get to the 3 degree angle i had to cut underneath it exhaust cut outs. The headers were in more than the arches so i had to remove even more metal and offset the crossmember to the right side of the engine. Total PITA.

I still need to learn it up and paint it.
http://i30.photobucket.com/albums/c302/icemanrld19/11099937_10100653525970996_4194664078682039236_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11099937_10100653525970996_4194664078682039236_n.j pg.html)

http://i30.photobucket.com/albums/c302/icemanrld19/11826069_10100653525995946_404240692632503258_n.jp g (http://s30.photobucket.com/user/icemanrld19/media/11826069_10100653525995946_404240692632503258_n.jp g.html)

well this sucks to see, I ordered this crossmember as well for my swap.I was looking back through your thread and I saw you had a hurst driveline crossmember then you said you got the speedtech cross member, did you have issues with those as well?

[MCB Matt]

We sell quite a few Speedtech's and BMR's. Issues with those have been minor to none.

Of course in this hobby there area lot of off-the-shelf parts that need to be tweaked to suit your needs, but you have to pretty much reinvent the wheel with that one!

Matt

[randy]

well this sucks to see, I ordered this crossmember as well for my swap.I was looking back through your thread and I saw you had a hurst driveline crossmember then you said you got the speedtech cross member, did you have issues with those as well?

See i want my exhaust close to the floor and to get my driveline angle at 3 degrees. This wouldn't be so bad if i wanted my exhaust to hang little but i don't and my car is slammed. Not to mention the slip on connectors with my stainless works headers didn't fit well either. the bungs location would hit the crossmember

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/11846722_10100654819538676_6728932739520720605_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11846722_10100654819538676_6728932739520720605_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/11822792_10100654819588576_5375486531674071321_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11822792_10100654819588576_5375486531674071321_n.j pg.html)

[randy]

thoughts?
http://www.eddiemotorsports.com/prod...el-ms140-54bk/



I also purchased this dipstick handle cover. I love it love it love it. Simple for $25 and covers that ugly yellow handle
http://www.phastekperformance.com/20...120001-blk.htm

[randy]

http://i30.photobucket.com/albums/c302/icemanrld19/11231324_10100678567297976_387481630234051235_n.jp g (http://s30.photobucket.com/user/icemanrld19/media/11231324_10100678567297976_387481630234051235_n.jp g.html)
http://i30.photobucket.com/albums/c302/icemanrld19/11091395_10100678567512546_5962733508195203608_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11091395_10100678567512546_5962733508195203608_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12004800_10100678567811946_3037203077348942013_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12004800_10100678567811946_3037203077348942013_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/11218839_10100678567268036_6192419096663850019_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11218839_10100678567268036_6192419096663850019_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/11988480_10100678567941686_6242782608278237998_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11988480_10100678567941686_6242782608278237998_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12019967_10100678567861846_7481076882314548403_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12019967_10100678567861846_7481076882314548403_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12009787_10100678567437696_2645136611571591978_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12009787_10100678567437696_2645136611571591978_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/mufflers.jpg (http://s30.photobucket.com/user/icemanrld19/media/mufflers.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/Catch%20can.jpg (http://s30.photobucket.com/user/icemanrld19/media/Catch%20can.jpg.html)

There will get wrapped in leather
http://i30.photobucket.com/albums/c302/icemanrld19/11960265_10100672749911066_3907974693353248264_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/11960265_10100672749911066_3907974693353248264_n.j pg.html)

[MCB Matt]

Looking great. Post up a pic of the seats once you get them wrapped! Are you going to do any color matched stitching on them? You have that opportunity to make them exactly how you want!

Great work :cheers:

Matt

[waynieZ]

Its looking good! Nice seats

[randy]

Unsure what I'm going to do in the interior. See i like the stock but modified overall look

[Spiffav8]

Unsure what I'm going to do in the interior. See i like the stock but modified overall look

I agree. It's all about balance. Not easy to do.

Car is looking super sharp! How about some closer pics of that engine bay. I'd like to get a better look at how you ran things. That's going to be my next big challenge.

:captain:

[Sheck44]

Randy, I get a lot of comments on how people like the modded 'stock' look of my interior, and my seats are similar to yours ... anyway this may give you some ideas, and btw the seats are awesome

http://i264.photobucket.com/albums/ii200/SCOBRA48/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg (http://s264.photobucket.com/user/SCOBRA48/media/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg.html)

[randy]

I agree. It's all about balance. Not easy to do.

Car is looking super sharp! How about some closer pics of that engine bay. I'd like to get a better look at how you ran things. That's going to be my next big challenge.

:captain:

what would you like to see? Im working on it all day friday and we have 2 other cars that i can take pic of

[randy]

Randy, I get a lot of comments on how people like the modded 'stock' look of my interior, and my seats are similar to yours ... anyway this may give you some ideas, and btw the seats are awesome

http://i264.photobucket.com/albums/ii200/SCOBRA48/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg (http://s264.photobucket.com/user/SCOBRA48/media/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg.html)

Your interior does look great. That would be the farthest modified i would do. I would leave the recaro letters off, do the stitching, Change the window cranks and door handles is what i was thinking so far

[MCB Matt]

Randy, I get a lot of comments on how people like the modded 'stock' look of my interior, and my seats are similar to yours ... anyway this may give you some ideas, and btw the seats are awesome

http://i264.photobucket.com/albums/ii200/SCOBRA48/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg (http://s264.photobucket.com/user/SCOBRA48/media/WAAAY%20OTT/IMG_4304_zpsudiisudw.jpg.html)

Very well done! Not overstated, but much cleaner and more practical than stock. I like my builds the same, overall stock "look" but tasteful modern touches.

[randy]

T56 magnum

- tremecs website say Dexron III ATF and it also says not to use full synthetic
- Now I've seen some people run redline d4 atf which is a synthetic.
- So why would tremec say not to use it yet steilow is using it in his car?
- What fluid is everyone else using? Synthetic or not?
- How many qt. do i need?

Ls3 480hp crate engine

- What oil is used to break in a new GM crate engine?
- I was thinking about using joe gibbs driven br30 oil to break it in.
- I don't think GM used break in oil so why not put 5w30 synthetic in right away?

dse ford 9" with tru track

- Do you use break in gear oil?
- Synthetic or reg?
- What weight and why?
-

[randy]

info for me
- Hook the vss output wire ( brown ) from the bulkhead to the speedometer signal wire
- Hook the tach ( white ) from the bulkhead to the gauge tach signal wire
- Hook the Oil pressure ( Tan/white ) from the bulkhead to the gauges signal wire
- For the water temperature, there is a port located on the right side (passenger side) of the engine, in the cylinder head, past the last exhaust port (closest to the firewall / flywheel). There is a plug threaded in this location, that can be removed. This threaded in plug will either require an 8mm Allen Wrench, or a T52 Torx bit. There will be no noticeable difference in temperature reading when using the shorter sender. The 2277 adapter requires a 3/4" wrench, and the 2259 sender requires a 12mm wrench. Be careful to only tighten the adapter into the head until the crush washer is flattened. Do not over tighten.
- for the voltmeter just hook up the ignition wire from the gauge harness to the gauge
- Samoco unit should be used for the reverse lockout solenoid. You could run it off of the brake pedal but some people have stated some issues. Link to the samoco unit is http://www.wirebarn.com/T56--TR6060-Reverse-Lockout-Control-Module_p_470.html
- The for fuel gauge run ......

[waynieZ]

T56 magnum

- tremecs website say Dexron III ATF and it also says not to use full synthetic
- Now I've seen some people run redline d4 atf which is a synthetic.
- So why would tremec say not to use it yet steilow is using it in his car?
- What fluid is everyone else using? Synthetic or not?
- How many qt. do i need?

Ls3 480hp crate engine

- What oil is used to break in a new GM crate engine?
- I was thinking about using joe gibbs driven br30 oil to break it in.
- I don't think GM used break in oil so why not put 5w30 synthetic in right away?

dse ford 9" with tru track

- Do you use break in gear oil?
- Synthetic or reg?
- What weight and why?
-

I was asking the same thing on CTSVoners.com waiting for info.

[randy]

I was asking the same thing on CTSVoners.com waiting for info.

Rear Diff fluid I'm going to run some valvoline 80w90 non synthetic

Trans fluid just some atf valvoline non synthetic for 500 miles and then switch to redline d4

Engine br30 to break it in and then 5w30 synthetic after that

[randy]

Current bulkhead layout.

http://i30.photobucket.com/albums/c302/icemanrld19/fuse%20box.jpeg (http://s30.photobucket.com/user/icemanrld19/media/fuse%20box.jpeg.html)

diagram for my transmission harness
http://i30.photobucket.com/albums/c302/icemanrld19/transmission%20connections.jpeg (http://s30.photobucket.com/user/icemanrld19/media/transmission%20connections.jpeg.html)

[randy]

for anyone that wants to remove some of the couplers from the airraid u-build it kit i did the following.

used the 90 with log straight that i wanted, Found the other angle to cut it around the radiator by temp keeping it together with superglue. I then found the other angle to make a straight transition to the fender pocket and temp used superglue for that angle. Removed the intake tube, marked the 2 extra angles with a marker so it stays clocked right, and used gorilla epoxy to form a strong bond. Allowed everything to sit overnight and sanded everything smooth. Not bad for about $150 plus a lot easier than welding aluminum. Since my close out panel is mounted on the inside of the fender i used 6" inlet and 6" deep k&n filter. If you mounted the filter other the engine bay side of the fender you could use the 6" by 7 1/2 filter . Spectra makes a nice 4" to 6" filter adapter that bolts to the close out panel for $10 or $15 i don't remember. All in all My complete intake setup cost me about $200 to $220

Billet specialties makes a very very nice billet coolant overflow tank. Theres already two holes in the core support that line up. You just have to enlarge them. The mount is about dead middle with the headlight bracket mount but its in line with the two headlight bolts to core support. Nice and clean.

Trying to finalize my ecu and fuse box placement under the dash so i can finish the rest of the wiring. Already have the spal fan connectors and used marine grade wire. Routed the fan wires from inside the car to the blower close out panel in the inner fender by adding a grommet in it. If i don't have enough room i might just make a center console and mount them under that.

Inside the passenger fender i have constant and accessory fused ports mounted to a bracket if i ever needed to power anything up there.

Went with the retro-electro headlight motors which i love, dse wiper mounted is routed inside the AAW fuse harness

As far as under the hood all i need is to route the vintage air hoses, steam vent tube, and add the connectors on the end of my fan wires.


http://i30.photobucket.com/albums/c302/icemanrld19/12523147_10100747439522486_3731485608560434969_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12523147_10100747439522486_3731485608560434969_n.j pg.html)

[tubbed69]

Looking good Randy,that is a very nice overflow tank.I used it on mine and also mounted it there.

[boydx6]

How was the DSE wiper motor install? Any issues?

[randy]

How was the DSE wiper motor install? Any issues?

zero issues. very simple to modify so it plugs into my AAW harness. one thing that i wanted to make sure of is that everything in the car can be unplugged. From the revearse lockout box, to the taillights, to the retro-electro motors.

[randy]

Engine bay is done for now. All wiring is complete. 2 heater hose lines and 2 ac lines under the dash and i can fire the motor up

Simple close out panels that cost me less than $10 to make including hardware

Terrible pictures but you get the idea. Was going for the factory look. Could use some slight dressing up
http://i30.photobucket.com/albums/c302/icemanrld19/12804676_10100772435230886_7266631753023968088_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12804676_10100772435230886_7266631753023968088_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12799306_10100772435270806_3652492576471519004_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12799306_10100772435270806_3652492576471519004_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12795268_10100772435300746_5155925930024321131_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12795268_10100772435300746_5155925930024321131_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/12802721_10100772435250846_5778696375374433119_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/12802721_10100772435250846_5778696375374433119_n.j pg.html)

[WSSix]

Very nicely done. The colors all go together well. I think you nailed the factory look.

[randy]

https://www.facebook.com/rodney.moore.545/videos/1233664080007719/

see if this works

[MCB Matt]

It came together so well! Just in time for spring. Is it just about ready for some shake down runs?

Keep moving, your progress is inspiring!

Matt

[waynieZ]

Sounds so sweet!!!

[randy]

Looking forward to my next day off to look over everything and get some break in runs in it :)

Goodguys is this weekend so i won't be working on it sat.

- Adjust the doors to open and close better
- Figure out why the oil pressure, speedometer and tach are working. Should be a easy fix and recalibrating the gauges
- paint the gauge holder, and ac vents gloss black
- Install front and rear glass
- Install front and rear trim
- Remount the vintage air unit and plug in
- Flash the ecu with the pcm of nc dual fan patch
- find a spot to mount the ecu
- Break the car in
- Recheck everything on the car and alignment
- Send seats out to get redone after i wipe the smile off of my face.

[waynieZ]

Sounds like a plan to me!

[randy]

so last mondays hail storm causes some damage. Shop windows got busted out and dumped glass all over my car. every body panel has a scratch and the trunk lid has 3 dents in it. I was able to clean out the water but the car will need repainted. When life gives you lemons you make lemonade

http://i30.photobucket.com/albums/c302/icemanrld19/Mobile%20Uploads/IMG_3084.jpg (http://s30.photobucket.com/user/icemanrld19/media/Mobile%20Uploads/IMG_3084.jpg.html)

so Im debating on coloring matching the bumper and smoothing it, painting the tail panel titanium to match the wheel centers as well and the outside chrome ring and black portion on the tail light titanium since one of the tail lights got scratched as well.

http://i30.photobucket.com/albums/c302/icemanrld19/Mobile%20Uploads/a45c8b21-1e52-4f91-9ae5-505547d1add8_zpsac2ecf97.jpg (http://s30.photobucket.com/user/icemanrld19/media/Mobile%20Uploads/a45c8b21-1e52-4f91-9ae5-505547d1add8_zpsac2ecf97.jpg.html)

I would love to do this to the bottom part of my car but i dont want to spend any extra money on welding and bodywork.

http://i30.photobucket.com/albums/c302/icemanrld19/Mobile%20Uploads/Snowblind-SEMA4.jpg (http://s30.photobucket.com/user/icemanrld19/media/Mobile%20Uploads/Snowblind-SEMA4.jpg.html)

[CamaroAJ]

so last mondays hail storm causes some damage. Shop windows got busted out and dumped glass all over my car. every body panel has a scratch and the trunk lid has 3 dents in it. I was able to clean out the water but the car will need repainted. When life gives you lemons you make lemonade

Are you in the San Antonio area? I knew quite a few people that had a bunch of Windows and cars damaged last Monday in that storm.

[tubbed69]

Randy I am sorry to see all that damage,that does suck.

[68Cuda]

Are you in the San Antonio area? I knew quite a few people that had a bunch of Windows and cars damaged last Monday in that storm.

That shop is in Wylie, TX. Wylie was hammered pretty hard, I have friends who showed me pictures of hail bigger than softballs. Randy and I live North and West 10+ miles from there, our weather was a bit kinder.

[randy]

guess while I'm at it and waiting for my paint delemia to be figured out ill mount the ecu under the passenger seat like this.
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_6379.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMG_6379.jpg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/IMG_6378.jpg (http://s30.photobucket.com/user/icemanrld19/media/IMG_6378.jpg.html)

[randy]

Well I'm finally coming to completion with the insurance company and my car. Should finalize something soon and get the car repainted. When i do I'm going to black out the panel. Heres an example from today.

http://i30.photobucket.com/albums/c302/icemanrld19/13435424_10100854158367066_6961682311728572390_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13435424_10100854158367066_6961682311728572390_n.j pg.html)

http://i30.photobucket.com/albums/c302/icemanrld19/13428392_10100854158342116_4013969340952773847_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13428392_10100854158342116_4013969340952773847_n.j pg.html)

I also ordered myself a nice H3R hg250r fire HalGuard fire extinguisher after seeing big reds fire. I will have one attached to my seat and another in the left side of my trunk. IM using drakes off road fire mount. Another great piece.
http://i30.photobucket.com/albums/c302/icemanrld19/205-accessorymount.jpg (http://s30.photobucket.com/user/icemanrld19/media/205-accessorymount.jpg.html)


http://i30.photobucket.com/albums/c302/icemanrld19/528-HG250R.jpg (http://s30.photobucket.com/user/icemanrld19/media/528-HG250R.jpg.html)

Now I'm debating about getting some fesler door handles and paint the inlay titanium to match the wheels. The other piece of the handle will be polished. sorta like this but instead of matte the insert will be titanium

http://i30.photobucket.com/albums/c302/icemanrld19/02454502_0.jpg (http://s30.photobucket.com/user/icemanrld19/media/02454502_0.jpg.html)

Last but not least i dropped off my seats to get redone identical to these. Pleather outers, suade inners and orange stitching.
http://i30.photobucket.com/albums/c302/icemanrld19/13406883_10100854158471856_4938544867915943953_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13406883_10100854158471856_4938544867915943953_n.j pg.html)

[cpd004]

Awesome car!

[Dr. Jekyll]

Wow just found this thread, great build so far and sorry to hear about the damage. Glad to see insurance will help you with the repairs!

[randy]

Yes the insurance company was great and easy to deal with. I went with grundy. Great rates as well. Car will be on the road in 3 or 4 weeks. Doubt I have my seats done in time and interior finalized but the outside will be completed

[Dr. Jekyll]

Awesome, I'm looking forward to seeing the updates!

[randy]

So i used some wrap and i like this look. This was satin. The question is what does everyone recommend as far as painting satin? Just spray satin black and leave it? how would it stand up? Bumper will be back from the chrome shop next week as well

I was thinking Satin black paint and then satin clear would be the best. Any recommendations? Picking the wrong black could really ruin the car. I don't want it flat but i also don't want it glossy.
http://i30.photobucket.com/albums/c302/icemanrld19/2.jpg (http://s30.photobucket.com/user/icemanrld19/media/2.jpg.html)

Car now has its cuts and bruises fixed.

http://i30.photobucket.com/albums/c302/icemanrld19/new%20paint.jpg (http://s30.photobucket.com/user/icemanrld19/media/new%20paint.jpg.html)

[Dr. Jekyll]

Did you consider painting it gloss black and then a clear satin wrap over it to see how you'd like it over time? Since it's a smaller area you can always remove or replace the wrap as needed. Just a thought. If you do spray it black just add a satin clear. They make sealants specifically for satin finishes so you can still protect that part.

[jack67rs]

Way to push thru, looks awesome.

[68Cuda]

Did you consider painting it gloss black and then a clear satin wrap over it to see how you'd like it over time? Since it's a smaller area you can always remove or replace the wrap as needed. Just a thought. If you do spray it black just add a satin clear. They make sealants specifically for satin finishes so you can still protect that part.

Randy - I assume Rodney painted the whole car one color... I like this suggestion, I would take it one step further. Leave the rear copper, get a wrap made for the tail panel that is satin black. Done! Then, if you want to go gloss black or change back to copper just peal it off.

[waynieZ]

Sweet!

[randy]

Finally outside assembly is almost completed. SEM eurojet trim black satin is what i went with. Exactly the look i wanted

http://i30.photobucket.com/albums/c302/icemanrld19/blacked%20out%20tail%20panel.jpg (http://s30.photobucket.com/user/icemanrld19/media/blacked%20out%20tail%20panel.jpg.html)

[Dr. Jekyll]

That looks perfect, I love the contrast. Great job on getting her to the finish line!

[waynieZ]

It looks great. I really like the way it breaks up the tail and shows off the strip around the lights.

[randy]

seats should be done next week and then its time to break it in
http://i30.photobucket.com/albums/c302/icemanrld19/13769375_10100886156138276_1241284079465533127_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13769375_10100886156138276_1241284079465533127_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/13754162_10100886156038476_2431037668082816445_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13754162_10100886156038476_2431037668082816445_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/13645154_10100886156088376_436706838928233391_n.jp g (http://s30.photobucket.com/user/icemanrld19/media/13645154_10100886156088376_436706838928233391_n.jp g.html)
http://i30.photobucket.com/albums/c302/icemanrld19/13668957_10100886156193166_2231179250796225921_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13668957_10100886156193166_2231179250796225921_n.j pg.html)
http://i30.photobucket.com/albums/c302/icemanrld19/13770351_10100886155918716_7419150446723191857_n.j pg (http://s30.photobucket.com/user/icemanrld19/media/13770351_10100886155918716_7419150446723191857_n.j pg.html)

[randy]

i noticed whenever i was working on my car those little courtesy lights can get hot. Little did i know they were burning the sockets. I this on my under dash lights and my doom light so i replaced them with LEDS.

http://i30.photobucket.com/albums/c302/icemanrld19/Mobile%20Uploads/14733718858841051736378.jpg (http://s30.photobucket.com/user/icemanrld19/media/Mobile%20Uploads/14733718858841051736378.jpg.html)

went with these for the doom light
https://www.amazon.com/gp/product/B00B2YHHZY/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

and i went with these for the under dash lights. There is already a hole in the dash where your vent handles would come out of. I opened those holes up to fit these lights in there and now the lights are brighter and less heat.
https://www.superbrightleds.com/moreinfo/led-wired-bolts/bolt-beam-12mm-led-light/1494/


Also anyone else have their rear diff make some noise at lower speeds? I heard a few cars make this clicking noise running the true trac diff.

video coming shortly

[randy]

if you want to rekey your ignition to match all of your other locks follow these instructions.There's a metal clip inside the cylinder, pop the cover off and you will see 6 springs, take the springs out then you have 6 y shaped clips with diff height notches in them. Take them out and like the notches back up with the new key using a blank lock, take the y clips back out remembering what order in the cylinder and reinstall the springs and cover and your done. Now i have 1 key for my glove box, door locks, trunk and to start my car.

[MCB Matt]

if you want to rekey your ignition to match all of your other locks follow these instructions.There's a metal clip inside the cylinder, pop the cover off and you will see 6 springs, take the springs out then you have 6 y shaped clips with diff height notches in them. Take them out and like the notches back up with the new key using a blank lock, take the y clips back out remembering what order in the cylinder and reinstall the springs and cover and your done. Now i have 1 key for my glove box, door locks, trunk and to start my car.

Another option, the new lock "kits" come with all the locks, gaskets, retainers AND are all keyed alike!

I enjoy re-keying, I learned it from my father, but in the case, especially if a few could use replace, the new set makes sense and is not very expensive.

Matt

[DKz Garage]

WOW! The car looks absolutely beautiful!! Great choice of color/wheels/stance/Interior...... I'm sure you are stoked to get on the road!

[randy]

https://m.facebook.com/video_redirect/?src=https%3A%2F%2Fvideo-dft4-2.xx.fbcdn.net%2Fv%2Ft42.1790-2%2F14439103_295264504178387_2625043849076015104_n .mp4%3Fefg%3DeyJybHIiOjMwMCwicmxhIjo1MTIsInZlbmNvZ GVfdGFnIjoic3ZlX3NkIn0%253D%26oh%3Dbbf587af7875b4d dffa98a771cfa5c66%26oe%3D57E34B70&source=media_collage&id=10100932853192006&refid=18&ref=m_notif&notif_t=like&__tn__=F

https://m.facebook.com/video_redirect/?src=https%3A%2F%2Fvideo-dft4-2.xx.fbcdn.net%2Fv%2Ft42.1790-2%2F14435520_603862666480324_381419595833016320_n. mp4%3Fefg%3DeyJybHIiOjMwMCwicmxhIjo1MTIsInZlbmNvZG VfdGFnIjoic3ZlX3NkIn0%253D%26oh%3Dd762320a7369730d 917e36a820fd6028%26oe%3D57E34ED8&source=media_collage&id=10100932853182026&refid=18&ref=m_notif&notif_t=like&__tn__=F

[Dr. Jekyll]

Any more updates?

[68Cuda]

I saw the car at Goodguys show at TMS on Oct 1st.

http://www.rodscarcraft.com/customeruploads/var/albums/67-Camaro/DSC09774.JPG

http://www.rodscarcraft.com/customeruploads/var/albums/67-Camaro/DSC09775.JPG

http://www.rodscarcraft.com/customeruploads/var/albums/67-Camaro/DSC09779.JPG

http://www.rodscarcraft.com/customeruploads/var/albums/67-Camaro/DSC09780.JPG

[waynieZ]

Thanks for the pictures, the car came out beautiful!! Well done.

[randy]

ride height almost perfect for my liking. Front end bounce alittle so eventually ill upgrade the front coil overs as well
http://i30.photobucket.com/albums/c302/icemanrld19/stance_1.jpg (http://s30.photobucket.com/user/icemanrld19/media/stance_1.jpg.html)

After goodguys i decided to change this up.
http://i30.photobucket.com/albums/c302/icemanrld19/before.jpg (http://s30.photobucket.com/user/icemanrld19/media/before.jpg.html)

Started by making coil pack boxes and placing the coil packs on the subframe. They are stacked two high. Wires are ran behind the headers and between the engine mounts and subframe.
http://i30.photobucket.com/albums/c302/icemanrld19/coil%20packs.jpg (http://s30.photobucket.com/user/icemanrld19/media/coil%20packs.jpg.html)

Which lead to this look
http://i30.photobucket.com/albums/c302/icemanrld19/after%201.jpg (http://s30.photobucket.com/user/icemanrld19/media/after%201.jpg.html)

After searching my ass off for some 19156430 valve covers that are discontinued i found a set at a dealership in houston. SO now I'm here. Trying to decide to leave it alone or paint the letters to color match my car. Thoughts?
http://i30.photobucket.com/albums/c302/icemanrld19/valve%20cover.jpg (http://s30.photobucket.com/user/icemanrld19/media/valve%20cover.jpg.html)

[waynieZ]

Either way will look good. I love that picture in front of the garage. Do you remeber what that top radiator hose was from or a part number?

[Spiffav8]

ride height almost perfect for my liking. Front end bounce alittle so eventually ill upgrade the front coil overs as well
http://i30.photobucket.com/albums/c302/icemanrld19/stance_1.jpg (http://s30.photobucket.com/user/icemanrld19/media/stance_1.jpg.html)

Uh....yeah, that's sick. :thumbsup: :thumbsup:

After searching my ass off for some 19156430 valve covers that are discontinued i found a set at a dealership in houston. SO now I'm here. Trying to decide to leave it alone or paint the letters to color match my car. Thoughts?
http://i30.photobucket.com/albums/c302/icemanrld19/valve%20cover.jpg (http://s30.photobucket.com/user/icemanrld19/media/valve%20cover.jpg.html)

It could go either way, but I think it's perfect as is.

[Beechy]

:king:

Second vote for Black.........

[Mikael A]

yes definitely black, you got this perfect clean oem look.

[Sonar Chief]

yes definitely black, you got this perfect clean oem look.

X2 :thumbsup: such a great looking car!!!

[Dr. Jekyll]

Hey buddy how are things coming along?

[randy]

https://www.youtube.com/watch?v=SHzZVs1wntI


https://scontent.xx.fbcdn.net/v/t1.0-9/17352543_10101112013523266_1906976037101606383_n.j pg?oh=010d0d323227186a2eddb5033c8ff605&oe=5953B3F6

https://scontent.xx.fbcdn.net/v/t1.0-9/17424986_10101112013817676_1551065377352611607_n.j pg?oh=c23cc143e56c231006926edeaa22b6b6&oe=59731722

[Dr. Jekyll]

WOW!!! What a blast! How fast were you allowed to take it? Are there any special requirements for the car?

[DT69Cam]

That engine bay looks sick. Which accessory drive and AC compressor did you use, thx!!

[randy]

Well after looking at the rules there are no rules for speed. You just can't pass the pace car. Next time we are really going to get on it since I was a rookie and didn't know what I could get away with

Accessories are corvette with kwik ac bracket

[DT69Cam]

Well after looking at the rules there are no rules for speed. You just can't pass the pace car. Next time we are really going to get on it since I was a rookie and didn't know what I could get away with

Accessories are corvette with kwik ac bracket

Thank you