Lateral-g Forums - Hobbs Camaro (Old Drag Car)

Page 10 of 48

« First

Last »

Show 40 post(s) from this thread on one page

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)

- Project Updates (https://www.lateral-g.net/forums/forumdisplay.php?f=16)

- - Hobbs Camaro (Old Drag Car) (https://www.lateral-g.net/forums/showthread.php?t=59856)

camcojb

08-01-2023 11:12 PM

You are way too busy my friend... :lol:

EVIL SS

08-31-2023 09:23 AM

Quote:

My number one question about my cars is “What is the wheel offset”? Over the years we have found it easier for the rear wheels to order the wheels then build the axle to fit. It is easier to modify the axle tube than it is to get new wheels.

I was going to use a retro wheel, but I could not get the brakes to fit. The crew at Forgeline did a lot of work to attempt to get it to work. For me form follows function. I really wanted a retro wheel but I think these look great. If I really want the old dog dish look I’ll swap the brakes to sliders and order new wheels.

Looks great so far!! I you assume start with a known offset and adjust from there? What brakes are you going to run on this car?

Stielow

08-31-2023 09:47 AM

Hobbs Camaro (Old Drag Car)

Quote:

Originally Posted by EVIL SS (Post 723911)

Looks great so far!! I you assume start with a known offset and adjust from there? What brakes are you going to run on this car?

The Detroit Speed subframe works well with a 18x10 front with a 20 mm offset or 6.25 backspacing. The rear we ordered a 18x12 with the most backspacing that Forgeline could do in there forging. Off memory it as 19 mm offset 7.25 backspacing.

I think I will have 2 sets of brakes for this car. The track setup with the Brembo and Monoblock Forgeline wheel (Pictured below). To keep with look of the car I’m going to order new Forgeline OE wheels that will take poverty cap hub caps. For the OE style wheel I’ll need to run stock C6 Corvette brakes. For just cruising around the OE black steel looking wheels will work well.

https://uploads.tapatalk-cdn.com/202...d7598820e4.jpg
https://uploads.tapatalk-cdn.com/202...8939cddcad.jpg
https://uploads.tapatalk-cdn.com/202...4e7ba0ca70.jpg

The Forgeline OE wheel

https://uploads.tapatalk-cdn.com/202...08e763c522.jpg

Sent from my iPhone using Tapatalk

Stielow

08-31-2023 09:52 AM

Hobbs Camaro (Old Drag Car)

srode1

08-31-2023 10:03 AM

Did he redo the VIN hole to match original or did you get a top that does look correct?

Stielow

08-31-2023 10:04 AM

Quote:

Originally Posted by srode1 (Post 723914)

Did he redo the VIN hole to match original or did you get a top that does look correct?

https://uploads.tapatalk-cdn.com/202...50133e1e97.jpg
Yes

Sent from my iPhone using Tapatalk

EVIL SS

08-31-2023 01:43 PM

Quote:

Originally Posted by Stielow (Post 723912)

Thanks Mark! Is this the same setup as your LT5 car with custom hats? I'm still looking for a good front brake setup for my LT5 build.

ScotI

08-31-2023 01:53 PM

Quote:

Originally Posted by Stielow (Post 723912)

The Detroit Speed subframe works well with a 18x10 front with a 20 mm offset or 6.25 backspacing. The rear we ordered a 18x12 with the most backspacing that Forgeline could do in there forging. Off memory it as 19 mm offset 7.25 backspacing.

I think I will have 2 sets of brakes for this car. The track setup with the Brembo and Monoblock Forgeline wheel (Pictured below). To keep with look of the car I’m going to order new Forgeline OE wheels that will take poverty cap hub caps. For the OE style wheel I’ll need to run stock C6 Corvette brakes. For just cruising around the OE black steel looking wheels will work well.

https://uploads.tapatalk-cdn.com/202...4e7ba0ca70.jpg

The Forgeline OE wheel

https://uploads.tapatalk-cdn.com/202...08e763c522.jpg
Sent from my iPhone using Tapatalk

I was curious what the OE1's allowed as far as brakes (aggressive brake packages or limited to production based).

Stielow

08-31-2023 01:55 PM

Quote:

Originally Posted by EVIL SS (Post 723917)

Thanks Mark! Is this the same setup as your LT5 car with custom hats? I'm still looking for a good front brake setup for my LT5 build.

Yes similar set up. I had Howell make custom rotors for the back with the stock ZR1 hats.

Brakes are a personal choice. I like the Brembo stuff because I know it and I know the Brembo engineers, both on the production side and the racing side.

I know a lot of people are use a lot of other brands with no issues.

Sent from my iPhone using Tapatalk

Stielow

09-01-2023 07:47 AM

Quote:

Originally Posted by ScotI (Post 723918)

I was curious what the OE1's allowed as far as brakes (aggressive brake packages or limited to production based).

You can run “Big” or oppose piston brakes with the OE Forgeline wheel. It just pushes the center out board and make the center cap look odd.

See attached photos. The outer rim half is not very deep and IMO the center cap pushed out like this is not my preference.

https://uploads.tapatalk-cdn.com/202...fda39bf6c1.jpg
https://uploads.tapatalk-cdn.com/202...3bd8ba048a.jpg

Sent from my iPhone using Tapatalk

All times are GMT -7. The time now is 02:52 AM.

Page 10 of 48

« First

Last »

Show 40 post(s) from this thread on one page