Lateral-g Forums - 69 camaro super charger ls6 t56 SKUNKWORKS

Page 11 of 35

« First

Last »

Show 40 post(s) from this thread on one page

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)

- Project Updates (https://www.lateral-g.net/forums/forumdisplay.php?f=16)

- - 69 camaro super charger ls6 t56 SKUNKWORKS (https://www.lateral-g.net/forums/showthread.php?t=28848)

Lenie

12-16-2012 12:11 AM

I had my whole exhaust system (headers back) Jet coated, still got hot so now I've wrapped my exhaust w/header wrap and custom stitched a heat blanket fot just the top of my mufflers. Haven't installed them yet but should in the next couple of days, I'll let you know how it goes. Good luck. Thanks for the advice Ron.

frankv11

12-19-2012 08:16 AM

Ron
I've gone back and changed those sharp angles at rear, I did'n like them either was just being lazy.

http://i1232.photobucket.com/albums/.../photo2-16.jpg
http://i1232.photobucket.com/albums/.../photo4-15.jpg
http://i1232.photobucket.com/albums/.../photo5-10.jpg

Ron in SoCal

12-19-2012 09:00 AM

That looks killer Frankie :thumbsup: :thumbsup: :thumbsup:

cencalc6

12-19-2012 09:28 AM

Very Nice Job Frank! :hail: :thumbsup:

CarlC

12-19-2012 10:17 AM

Quote:

Originally Posted by dontlifttoshift (Post 451920)

I'm sure you could get there with math, as well.

0.461" for 304SS

The other part to consider is that all sections get longer, that means some sections of the tube structure will get wider as well. Flexible hangers come in hand for such things.

Very nice tube fabrication!

frankv11

12-21-2012 08:32 AM

Quote:

Originally Posted by CarlC (Post 452574)

Thanks Carl , I will be in contact. going to be needing control module for Vaporworks tank.

got to figure out how to quote multiple comments, any how thanks phil and Ron " We need up dates on both builds"

makoshark

01-21-2013 09:32 PM

Quote:

Originally Posted by frankv11 (Post 451914)

You are absolutely correct but I have a trick up my sleeve for that:D
That was something else that I thought about but if I run bracket on exhaust and another on body w 3/8" bolt to hold grommet together. It will not give it room to grow. I'm trying to guide the expansion by way of hangers so it will not compromise the close tolorances to body at certain places.. I have the whole system tucked in there pretty tight. For now it's just theory I'll see how it behaves once I put some heat to it..
Good eye

Cut a groove in the rod and snap a c-clip on it to hold the grommet in place.

By the way, I'm still contemplating on stealing your exhaust idea:)

waynieZ

01-21-2013 09:49 PM

Those sure are pretty, Nice job.

frankv11

01-21-2013 10:16 PM

Quote:

Originally Posted by makoshark (Post 459663)

Cut a groove in the rod and snap a c-clip on it to hold the grommet in place.

By the way, I'm still contemplating on stealing your exhaust idea:)

That will hold the grommet together but would not let exhaust slide back and forth freely. I'm thinking something along the lines of safety wire..
No need to steal. I'm willing to donate!:D

Quote:

Originally Posted by waynieZ (Post 459665)

Those sure are pretty, Nice job.

Thanks Wayne. Hope all is well with you, how is that project coming along?

waynieZ

01-22-2013 04:23 PM

Thanks Wayne. Hope all is well with you, how is that project coming along?[/QUOTE]

Thanks for asking. Pretty slow right now but getting ready to get back on it.

All times are GMT -7. The time now is 11:38 AM.

Page 11 of 35

« First

Last »

Show 40 post(s) from this thread on one page