|
Update Time!
Logistics, logistics, logistics. Mainly on wheels for George. We finally had Ben @ Hermance Designs do a rending for him to try our several wheels after looking at some very expensive options he landed on the Showwheels and here we are. http://nerdrods.com/Images/customer/...2015_final.jpg We've also been busy with the version 7 TriFive Car frame and lots of carts and other fabrication and handling equipment here in the shop. Its been busy, just doesn't look that way from the outside looking in. Here's just one of the rolling chassis's that's been pushed out the door since we've been out of touch. http://www.trifive.com/forums/showthread.php?t=128100 And a roadster we've started on recently as well. https://lateral-g.net/forums/showthread.php4?t=49673 But the CAM is in as of today, and the wheels should be here shortly. So next the truck can come in and we can lock down the chassis. More photos to come shortly. Later -Russell |
rendering looks good, Beautiful job on the frame Russell.
|
Thank you sir
So we finally flow tested the gas tank. The shop water hose filed a 5 gallon bucket in 1:15. When I topped my bike of the other day it took 1:35 to fill 4 gallons so we're good there. We hooked it all up with all the bends to get up to the stock filler neck on the truck and let her rip. Test came out perfectly and we're good to go. http://gallery.nerdrods.com/Customer...8_10.00.28.jpg http://gallery.nerdrods.com/Customer...8_10.00.36.jpg With that confirmed I ordered up 2 more tanks. We recently had frame #2 returned to us for completion. They had purchased it as a stage 2 for a father son project but with the son in high school they hadn't touched it. So it went from a stage 2, to a stage 3, and finally they asked for a stage 4 running chassis with a 5.3L LS and an automatic so one tank for them and one for stock. So you'll see some of their photos in here as well. The cool thing if I can swing it will be that George's is a tall body and The Webb's truck is a low body so if I do this right we can have some side by side stance photos soon. http://gallery.nerdrods.com/Customer...1-_H6A1650.jpg We got George's motor cleaned up and a coat of paint on it and the transmission to spruce it up a bit after the CAM swap. CAM, Push Rods, Valve Springs, and a light stall torque converter. But is all back together and in the frame for the last time http://gallery.nerdrods.com/Customer...0-_H6A1641.jpg http://gallery.nerdrods.com/Customer...3-_H6A1681.jpg http://gallery.nerdrods.com/Customer...3-_H6A1682.jpg http://gallery.nerdrods.com/Customer...3-_H6A1678.jpg We're making up all the lines and fitting the radiator core. Coolant, Power Steering, Transmission and so forth will all be worked out now and then the body fitted so we're not monkeying around under the hood. http://gallery.nerdrods.com/Customer...6-_H6A1688.jpg http://gallery.nerdrods.com/Customer...6-_H6A1687.jpg http://gallery.nerdrods.com/Customer...6-_H6A1685.jpg http://gallery.nerdrods.com/Customer...6-_H6A1684.jpg More to come soon, I've spent the last few months getting stock all worked out so we should flow through the project more quickly now. George's Gallery http://gallery.nerdrods.com/Customer...George%20W/06/ The Webb's Gallery http://gallery.nerdrods.com/Customer...ake%20Webb/01/ Later -Russell |
We’ll we’re waiting on a few things from the customer, namely the wheels, a final paint decision and some final budgeting plans for the level of finish out we’re going to be doing. So my hands are tired on a few things for now but the Webb’s truck will be getting the spot light for the time being so we should have two running trucks driving out of the shop shortly, one high and one low body stance.
So we’ve got the body on the frame now and we’re stared hooking up the final systems and doing the final checks on clearances for our kits so we can finalize the designs on those. http://gallery.nerdrods.com/Customer...8-_H6A1851.jpg http://gallery.nerdrods.com/Customer...-_H6A18549.jpg The CCP firewall mounted break pedal goes in beautifully but there are almost no instructions about it so Jim is going to do a video about its installation. While the frame in its high body placement is a no body modification fit you will still need to install the firewall master cylinder and that reacquires cutting on your body. So we want a video showing that so people will know what modifications are needed and specifically how hard they are. Jim said he should be able to do the next one in 30 minutes so look forward to that. http://gallery.nerdrods.com/Customer...8-_H6A1852.jpg http://gallery.nerdrods.com/Customer...9-_H6A1862.jpg http://gallery.nerdrods.com/Customer...9-_H6A1861.jpg http://gallery.nerdrods.com/Customer...9-_H6A1858.jpg There is also a lot of room to the engine that we don’t normally have on the TriFive’s so larger systems like the 8” or 9” boosters are an option here for people who want some serious braking power. http://gallery.nerdrods.com/Customer...9-_H6A1864.jpg http://gallery.nerdrods.com/Customer...9-_H6A1865.jpg |
Georges truck is waiting on parts for the time being so we're working on the Webb's truck so the kid can drive it a bit before he takes off to collage in a few weeks. So its hammer time.
The complete photo gallery can be found here. http://gallery.nerdrods.com/Customer...ake%20Webb/02/ Got the heat shields done for the mufflers. http://gallery.nerdrods.com/Customer...0-_H6A2103.jpg And picked up their cab. http://gallery.nerdrods.com/Customer...6-_H6A2553.jpg http://gallery.nerdrods.com/Customer...6-_H6A2557.jpg http://gallery.nerdrods.com/Customer...6-_H6A2558.jpg Got it back to the shop Monday night and by Wednesday afternoon it looked like this. http://gallery.nerdrods.com/Customer...7-_H6A2565.jpg http://gallery.nerdrods.com/Customer...8-_H6A2591.jpg The firewall and floor will be done this afternoon. We're going to do this truck 1" taller than the lowest possible so the ribs in the floor can be left alone and they can use the bench seat. Later -Russell @ Nerd Rods |
Nice progress. I like the tank too.:ohsnap:
|
Lots going on with both Georges truck and the Webb's
On the Webb's Got the engine fired up to check for leaks in the transmission cooler and fuel lines. http://gallery.nerdrods.com/Customer...5-_H6A2647.jpg http://gallery.nerdrods.com/Customer...5-_H6A2649.jpg Short video of here running for the customers https://www.youtube.com/watch?v=wODnGeehUvg Then I realized it was a mess and clean it up a bit for some nicer photos. You can see the tank hold downs and exhaust heat shields. Here I screwed up and didn't leave enough room for the heat shields and had to add a spacer to the tank to move it up to clear. I'll correct this in future designs by wrapping the mufflers and moving the exhaust down a little bit. http://gallery.nerdrods.com/Customer...8-_H6A2647.jpg http://gallery.nerdrods.com/Customer...8-_H6A2660.jpg http://gallery.nerdrods.com/Customer...8-_H6A2663.jpg http://gallery.nerdrods.com/Customer...8-_H6A2665.jpg http://gallery.nerdrods.com/Customer...8-_H6A2672.jpg And we got the body on for the last time. http://gallery.nerdrods.com/Customer...0-_H6A2710.jpg http://gallery.nerdrods.com/Customer...0-_H6A2711.jpg http://gallery.nerdrods.com/Customer...9-_H6A2688.jpg We had to do a little different floor board modification for the gas tank filler neck since we raised the tank a bit but it won't be hard to seal up. http://gallery.nerdrods.com/Customer...0-_H6A2699.jpg http://gallery.nerdrods.com/Customer...0-_H6A2704.jpg http://gallery.nerdrods.com/Customer...0-_H6A2706.jpg |
We also finally got the wheels for George's truck and got it on the ground to take a look at.
http://gallery.nerdrods.com/Customer...8-_H6A2675.jpg http://gallery.nerdrods.com/Customer...8-_H6A2677.jpg http://gallery.nerdrods.com/Customer...8-_H6A2680.jpg http://gallery.nerdrods.com/Customer...8-_H6A2683.jpg http://gallery.nerdrods.com/Customer...8-_H6A2686.jpg We're waiting on the paint booth to take Georges truck over for paint then we can do final assembly. Later -Russell @ Nerd Rods |
Battery mounted with an SKFab battery box and some bolts welded to the back of it so we could mount it to the firewall.
http://gallery.nerdrods.com/Customer...4-_H6A3000.jpg http://gallery.nerdrods.com/Customer...4-_H6A3005.jpg Power steering lines are done and you can see we're using the auto transmission cooler for a rack and pinion cooler. I went in the bottom and out the top to keep it from all back flowing into the overflow tank since its under the top line and cut down on the length of line. I also told the customer if I'm crazy and there is a problem I'll install another cooler and different lines on my dime later. The column shifter cable is installed and tuned. http://gallery.nerdrods.com/Customer...4-_H6A3002.jpg http://gallery.nerdrods.com/Customer...4-_H6A3003.jpg http://gallery.nerdrods.com/Customer...4-_H6A3007.jpg And the PRC Radiator System is installed for the final time and getting hooked up. We're going to use the radiator temp gauge hole for the steam vent line off the throttle body. http://gallery.nerdrods.com/Customer...4-_H6A3010.jpg http://gallery.nerdrods.com/Customer...4-_H6A3012.jpg http://gallery.nerdrods.com/Customer...4-_H6A3014.jpg Later -Russell @ Nerd Rods |
| All times are GMT -7. The time now is 06:19 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Lateral-g.net