The snubber brackets are not mounted in the same place on the frame rail so Brian removed them so we could install the cradle for the TCP rear suspension.

http://img.photobucket.com/albums/v3...astback/24.jpg

http://img.photobucket.com/albums/v3...astback/25.jpg

Cradle bolted and welded in place

http://img.photobucket.com/albums/v3...astback/28.jpg

http://img.photobucket.com/albums/v3...astback/29.jpg

Subscribed. Can't wait to see how the Dynacorn body works out.

The cradle is supposed to bolt to the pinnon snubber mount but there was no holes and it was off center a little.

http://img.photobucket.com/albums/v3...astback/30.jpg

Brian welded a bracket

http://img.photobucket.com/albums/v3...astback/34.jpg

Brian decided to improving the welding a little

http://img.photobucket.com/albums/v3...astback/37.jpg

http://img.photobucket.com/albums/v3...astback/38.jpg

http://img.photobucket.com/albums/v3...astback/39.jpg

They welded the other side

http://img.photobucket.com/albums/v3...astback/40.jpg

Test fitting the TCP front and rear suspension with Wilwood brakes

http://img.photobucket.com/albums/v3...astback/44.jpg

http://img.photobucket.com/albums/v3...astback/46.jpg

http://img.photobucket.com/albums/v3...astback/47.jpg

http://img.photobucket.com/albums/v3...astback/48.jpg

If only the doors, fenders & hood fit like this.

http://img.photobucket.com/albums/v3...astback/63.jpg

http://img.photobucket.com/albums/v3...astback/61.jpg

http://img.photobucket.com/albums/v3...astback/62.jpg

http://img.photobucket.com/albums/v3...astback/64.jpg

The deck lid fit great but the doors, fenders and hood are another story.

Once the fender apron holes were modified to get the fender back so there was not a large gap at the windshield and front of the hood there was not enough gap at the door.

http://img.photobucket.com/albums/v3...astback/73.jpg

The hood is to wide at the back and will need to be trimmed

http://img.photobucket.com/albums/v3...astback/75.jpg

http://img.photobucket.com/albums/v3...astback/76.jpg

Looks good so far can't wait to see it done.

Brian had to grind and add material to the door

http://img.photobucket.com/albums/v3...astback/78.jpg

After grinding

http://img.photobucket.com/albums/v3...astback/80.jpg

He also had to do the same to the front

http://img.photobucket.com/albums/v3...astback/82.jpg

http://img.photobucket.com/albums/v3...astback/83.jpg

The left vent window would not fit so Brian had to drill out the spot welds and bend the sheetmetal a little to allow the vent window to go in.

http://img.photobucket.com/albums/v3...astback/84.jpg

The bracket on the inside of the door where the bottom of the vent window attaches was in the wrong place and had to be moved

http://img.photobucket.com/albums/v3...astback/85.jpg

Brian had to narrow the hood than weld a strip on the back side

http://img.photobucket.com/albums/v3...astback/86.jpg

http://img.photobucket.com/albums/v3...astback/87.jpg

http://img.photobucket.com/albums/v3...astback/88.jpg