Lateral-g Forums
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)
-   Chassis and Suspension (https://www.lateral-g.net/forums/forumdisplay.php?f=38)
-   -   Feedback on subframes for 69 Camaro (https://www.lateral-g.net/forums/showthread.php?t=5667)

novanutcase 08-23-2006 01:10 AM
Quote:
Originally Posted by Mike Hall
Morrison does not have a bolt on front clip that i can find.

Mike
Weld In........ but you have to ask for it. They don't sell it as a kit so much as they will make it for the car you have!

BThibodeaux 08-23-2006 08:21 PM
Inner wheel housing opening relocate on WD subframe
 
OK, this may not be the thread to ask this question, but I have a querie. I spent this evening placing the stock inner fender wells over my WD subframe set up for C4 trying to determine how far back I need to move the opening. Wayne gave a general measurment of 3", but I came up with only about 2.25". Can I please get some feedback from those who have done it? How far did you move your openings, and did you do any additional trimming from the front or anywhere else to get it to look like you wanted it?
Jody? Anyone?

Thanks guys,
BT :willy:

camcojb 08-23-2006 09:48 PM
Quote:
Originally Posted by BThibodeaux
OK, this may not be the thread to ask this question, but I have a querie. I spent this evening placing the stock inner fender wells over my WD subframe set up for C4 trying to determine how far back I need to move the opening. Wayne gave a general measurment of 3", but I came up with only about 2.25". Can I please get some feedback from those who have done it? How far did you move your openings, and did you do any additional trimming from the front or anywhere else to get it to look like you wanted it?
Jody? Anyone?

Thanks guys,
BT :willy:
I believe mine cleared without any trimming, but was not centered with the a-arms. I had just coated the inner fenders so I left it. I believe DSE did the surgery later for Stuart.

Distance would be 2-3" as I remember, but only for looks.

BThibodeaux 08-23-2006 09:51 PM
Yes, only for looks. Sorry, I am kind of anal that way. Thank you so much for the super quick reply!

BT

Bowtieracing 08-25-2006 12:10 AM
Quote:
Originally Posted by Steve1968LS2
To run the T56 I raised the tunnel just under 2-inches 21st Century supplied me with the parts to raise the tunnel. If I would have ran a different trans I wouldn't of had to raise it. .

story on my subframe install will be in the December issue of PHR. If you need specific pics (of the trans tunnel mods) just let me know. I have several hundred pics of the install.
Hello Steve!!

Could you make a small "how to fit T56" in Lateral-g tech section? I think this would be a good technical help for many of us!!!

Teetoe_Jones 08-25-2006 10:08 AM
Quote:
Originally Posted by Bowtieracing
Hello Steve!!

Could you make a small "how to fit T56" in Lateral-g tech section? I think this would be a good technical help for many of us!!!
Here you go...

https://lateral-g.net/tech_articles/ats_t56_install/

Tyler

Bowtieracing 08-25-2006 10:31 AM
Quote:
Originally Posted by Teetoe_Jones
:unibrow: eeh sorry! Thats a good one!! I meant the floor pan modification.

Mean 69 08-25-2006 11:31 AM
Steve's t56 install is not a typical one due to the frame he is using, the floorpan needed to be modified anyway due to the motor placement, at least I am 99% certain that is the case.

Mark

Silver69Camaro 08-31-2006 02:15 PM
Quote:
Originally Posted by Mike Hall
Morrison does not have a bolt on front clip that i can find.

Mike
Ahem...well...wait a couple months...

Oops, did I say that?

TBART70 08-31-2006 04:23 PM
now you come out with it, It would have gone nicely with my tri-4bar set up.
oh well, too late now. :censored:


All times are GMT -7. The time now is 08:10 AM.
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright Lateral-g.net