Free shipping / PayPal fees
 

Why not use the Seals-it inner seal and keep the oil in the center where it's needed? You need to relocate the axle vent but there's no need for the oil to be in the axle tube. http://www.sealsit.com/axle-seals.html

Seals-it
 

Hi Tim,

I include the outer seal in the kit since this will suffice most consumers usage, but I have no issues at all with this option if requested.
I have spoken with the folks at Seals-it for input as to optimal shaft size (at seal location) for best overall longevity of the seal, so if requested I can accommodate folks that may want to go that route.

Also while talking with Seals-it, it was mentioned that not all housing tubes are a "out of the box fit" for their product and sometimes require different O-rings and or machining of the O-ring grooves to obtain their suggested fitment, and is another reason for my including the outer seals that are certain to fit everyone's application.

Your input is greatly appreciated and further exposes another great option that folks can explore.

Thanks, Jay

Jay, sent you a PM.

Placed my order for one of Jay's bolt on rear conversions. Will post an install thread once I get my axles. Great guy to deal with and has a great product!

Update
 

Updated my original post with some new info, pics, pricing, etc. Check it out.

https://lateral-g.net/forums/showthread.php4?t=49657

Thanks,

Jay

Just a quick picture of Hugger67RSSS at the Midwest Musclecar Challenge Friday (road course) & Saturday (auto-x). He is a regular competitor and is running one of the MillerBuilt "Bolt-On" Hybrid Floater Kits. He has been throwing everything at it but the kitchen sink and just keeps on ticking :thumbsup:

http://i35.photobucket.com/albums/d1...pseplkab3u.jpg

Oustanding ... great looking car, I'm gonna be ordering this same setup real soon. I'll send you a PM next week!

Michael

Michael,

Sounds good. Appreciate the support!

Jay

In stock!

https://lateral-g.net/forums/showthread.php4?t=49657

Ordered my kit today. Thanks again Jay for the great customer service. I look forward to installing the floater.

Thank you Brandon. Your support is MUCH appreciated! You're gonna love it :thumbsup:

FREE Shipping & PayPal This Weekend!!
 

FREE Shipping & PayPal This Weekend!! (8/6/16 & 8/7/16 - "lower 48" states only)

October Special!
 

FREE Shipping & PayPal through October!! ("lower 48" only)

Axle measurement
 

Jay-

I haven't gotten the kit installed yet, I ordered it through Tobin, but I am sitting here looking at it and wondering the best way to get measurements for cutting my axle shafts?

I have new axles that have extended splines on one end which allow for cutting to size.

Should I just assemble the whole rear end and brakes and then use my full length axles and see how much is sticking out?

Are there known measuring points we can use to calculate the length once we know what brakes and rear end lengths we have?

I know you provide this: **Note: this applications will add 3/16″ per side to your existing wheel mount surface (based on an existing 2.50″ axle/brake offset)** on a lot of the write ups, but I don't know if that is with all brake units. I guess I am wondering if I need to put my brakes on to see if I have that 2.50 brake offset to begin with.

I will be using Z51 with the parking brake assembly.

Thanks,
Dan

Dan,

First off, thank you for your purchase.

The brake package will not affect axle length in any way.

As for the axles...

Best way to determine your axle length is to know your pinion center to outside of Big Ford End measurement for both passenger and driver side. Once that is known just let me know and I will confirm your particular applications axle lengths.

In addition to the above, I will need to know what differential you are running and if your Big Ford Ends are on a GM 12 bolt, Ford 9, or?

PM me your email address if you prefer and I will get you over an order form which then can be used to document the above requested info and sent over to me

Jay

Thanks for the quick reply Jay. I have sent over a PM to you with my contact details.

It is a Strange 9 inch Ford narrowed 2" a side for my 65 Chevelle. It has the pro-iron 3.90 center section in it with 35 spline setup. Big Ford bearings.

Nice engineering! These kits get better looking all the time.

Jay ... thanks for answering all my questions and providing a solution! :thumbsup:

Customer support is great and quality Made in the USA parts too, can't go wrong here!

Michael

In Stock