Here ya go and he pretty much makes them for ever car possible.

https://badassfendercovers.com/collections/chevy?page=1

https://badassfendercovers.com/produ...o-fender-cover

Intake Tube Support Bracket (( 07-11-23 ))
 

Very early in the morning I dropped off my cardboard template and as Dennis at High Speed Welding to duplicate this in Aluminum.

http://garagescene.net/_data/i/uploa...0962333-me.jpg

Picked it up after work and also some new bolts for the upper control arm.

http://garagescene.net/_data/i/uploa...3a25b14-me.jpg

A Couple Small Projects (( 07-13-23 ))
 

Planning ahead once again.

I applied some putty over the screws that protrude into the tranny tunnel.

http://garagescene.net/_data/i/uploa...0675fad-me.jpg

I added some of the supplied oil to the vintage air fittings.

http://garagescene.net/_data/i/uploa...4f0c01b-me.jpg

My supervisor

http://garagescene.net/_data/i/uploa...bad3711-me.jpg

I drilled the final holes in the bracket that High Speed Welding made for me.

http://garagescene.net/_data/i/uploa...13fd42d-me.jpg

Test fitted and believe it or not it worked.

http://garagescene.net/_data/i/uploa...740d6fd-me.jpg

I stopped by Pro-Tek Powder Coating to pick up the freshly coated intake tube.

http://garagescene.net/_data/i/uploa...8e10016-me.jpg

I am hoping to have time to install it in the next couple days.

Upper Control Arm replacement bolt (( 07-15-23 ))
 

Quick Trip to Home Depot for some small hardware.

http://garagescene.net/_data/i/uploa...c621cb4-me.jpg

I have been dreading this project as my brain keeps telling me it's all going to go wrong. Honestly, All I need to do is replace
a bolt that is way to long. You can see I set the car up on the jack so I could take the weight off the suspension.

http://garagescene.net/_data/i/uploa...d2e1e8b-me.jpg

A little bit of cardboard to protect the paint.

http://garagescene.net/_data/i/uploa...5683b32-me.jpg

http://garagescene.net/_data/i/uploa...226b9d1-me.jpg

I also supported the suspension to prevent movement.

http://garagescene.net/_data/i/uploa...87600b3-me.jpg

This Bolt !!

http://garagescene.net/_data/i/uploa...fa0b5f6-me.jpg

Doing this by myself doesn't sound like a great idea and since I can't find my long extension I just stacked a bunch together.

http://garagescene.net/_data/i/uploa...f9c38d0-me.jpg

I covered everything painted as I know the socket is going to fall of since I have to become a contortionist to complete this task.

http://garagescene.net/_data/i/uploa...6c2f4ca-me.jpg

Dear Lord that was awful.

http://garagescene.net/_data/i/uploa...4abfba7-me.jpg

Anti-Seize has to be the most loved and hated thing when you are working on a car.

http://garagescene.net/_data/i/uploa...2cea360-me.jpg

Correct length bolt has been installed.

http://garagescene.net/_data/i/uploa...f684b1b-me.jpg

http://garagescene.net/_data/i/uploa...5b0baef-me.jpg

Later that night I was back out in the Grage (( 07-15-23 ))
 

The retaining clip was bad so just a another simple fix. I wrapped the sensor 2x with 3M High Temp electrical tape so it doesn't vibrate off.

http://garagescene.net/_data/i/uploa...c7e0a5e-me.jpg

The intake tubes are coated so it's time to install them.

http://garagescene.net/_data/i/uploa...4eea707-me.jpg

Bracket has been removed and for now it's getting rattle canned with Wrinkle Black. Over the winter I will
have the fan shroud and bracket powdered to match the Intake tube.

http://garagescene.net/_data/i/uploa...097621b-me.jpg

http://garagescene.net/_data/i/uploa...115f69a-me.jpg

http://garagescene.net/_data/i/uploa...1fa39da-me.jpg

It's getting closer

http://garagescene.net/_data/i/uploa...048a4af-me.jpg

http://garagescene.net/_data/i/uploa...fff61ac-me.jpg

I can't believe the stud lines up perfectly with the bracket.

http://garagescene.net/_data/i/uploa...d65345c-me.jpg

Heading to Ace Hardware to get a USS Nut ( these are very thin nuts )

http://garagescene.net/_data/i/uploa...c6d604d-me.jpg

Final Assembly Time

http://garagescene.net/_data/i/uploa...86dec04-me.jpg

http://garagescene.net/_data/i/uploa...6d89646-me.jpg

While I am here I might as well install the MAF Sensor.

http://garagescene.net/_data/i/uploa...540b1ed-me.jpg

http://garagescene.net/_data/i/uploa...81c36cc-me.jpg

I also installed two High Density Urethane washers to help reduce vibration and I will be using a Nylock nut to retain this bolt..

http://garagescene.net/_data/i/uploa...5600cca-me.jpg

Looks like things are lined up nicely.

http://garagescene.net/_data/i/uploa...9e66616-me.jpg

So Close !!!

I can't seem to find the hose clamp for the filter and the best Amazon can do is tomorrow.

http://garagescene.net/_data/i/uploa...791f71d-me.jpg

http://garagescene.net/_data/i/uploa...058fe55-me.jpg

http://garagescene.net/_data/i/uploa...a5679cf-me.jpg

Hey Marty I saw in previous post boxes of wilwood parts are you redoing the brakes ????

Hi Mike,

That box is the new Wilwood electric E-Brake set up.


Sent from my iPhone using Tapatalk

HoooooWeeeeeee that overhead engine pic is fire!! (as the kids say these days)

All that time spent tidying and color coordinating is paying off!

Thank you so much I really appreciate it and I hope to get out in the garage tonight.

Cant wait to see this!! everything looking super A+A+A+