That Shoddy workmanship just makes a guy Crazy !!!!..........Sheesh.....If they are going to take the time to fix some issues......Do it correctly !!!Great job Kev............

Ken

http://www.v8tvshow.com/1965_Impala_...1.03.14_08.JPG

Meanwhile, the crew was preparing to trial fit the Ridetech Street challenge suspension system on the Impala’s frame.

http://www.v8tvshow.com/1965_Impala_...1.09.14_05.JPG

This kit consists of tubular upper and lower control arms, specific rate coil springs and coil over shock assemblies, and an oversized front sway bar. We were also installing an upgraded quick ratio steering box.

http://www.v8tvshow.com/1965_Impala_...1.09.14_02.JPG

http://www.v8tvshow.com/1965_Impala_...1.09.14_19.JPG

The original front suspension design used a straight lower control arm and a radius rod bolted to it. The Ridetech design is a vast improvement, using an “A” shaped tubular lower arm with an articulating end in the forward mount rather than a rubber bushing.

http://www.v8tvshow.com/1965_Impala_...1.09.14_14.JPG

http://www.v8tvshow.com/1965_Impala_...1.11.14_02.JPG

http://www.v8tvshow.com/1965_Impala_...1.11.14_04.JPG

http://www.v8tvshow.com/1965_Impala_...1.11.14_05.JPG

You almost need an extra tall rotisserie for that big boy! That suspension kit should make a big difference in the ride and handling.

The rear suspension consists of tubular control arms with adjustable upper control arms, and a stronger panhard bar with improved bushings.

http://www.v8tvshow.com/1965_Impala_...1.09.14_22.JPG

http://www.v8tvshow.com/1965_Impala_...1.09.14_20.JPG

This frame had some old-school hot rod tricks, like these control arm support brackets that were stick-welded in. We removed them and reinforced the frame to appear more original.

http://www.v8tvshow.com/1965_Impala_...2.17.13_09.JPG

We disassembled the rear axle assembly and media blasted the housing.
http://www.v8tvshow.com/1965_Impala_...1.17.14_11.JPG

After epoxy and Imron enamel in satin black paint were applied, a new gearset was installed along with bearings and seals to make this 12 bolt rear axle like new again.
http://www.v8tvshow.com/1965_Impala_...1.22.14_04.JPG
http://www.v8tvshow.com/1965_Impala_...1.23.14_04.JPG
http://www.v8tvshow.com/1965_Impala_...1.23.14_12.JPG

Here, the yellow paint illustrates the proper gear mesh contact pattern ensuring quiet operation.
http://www.v8tvshow.com/1965_Impala_...1.23.14_15.JPG

Make sure you put the steel bushings in the lower control arm bushings where the Camber adjusting screw goes thru the cross member.....easy to miss....ask me how I know........If you need some let me know as I have an extra set.........Also....when you finish the car and get the front end aligned....We had to put a lot of pressure on the front strut rod to get some caster in the front........Because the strut rods are solid mounted in the spherical bushing in the front.......the lower arm pulled forward on the bushings and the control arms were now rubbing against the inside of the cross member.........so we ended up shimming the control arm to get the Caster without the pressure on the arms...............Just Say'in !!!!

Ken

Thanks for the feedback Ken! We always appreciate the tips from others who've been "down the road before..."

The front suspension parts bolted to the frame. These are obviously not torqued to spec for driving, but in place to mock-up the build.

http://www.v8tvshow.com/1965_Impala_...1.11.14_10.JPG

Quick-ratio steering gear.

http://www.v8tvshow.com/1965_Impala_...1.13.14_20.JPG

The body was placed back on the frame, and the whole rig was supported on jackstands. It was time to finish fitting the 6.0 LS and T56 transmission in the car.

http://www.v8tvshow.com/1965_Impala_...1.17.14_09.JPG

The transmission tunnel would need completion, but there’s only one way to know if something really fits, and that is to put it together and measure.

http://www.v8tvshow.com/1965_Impala_...1.17.14_16.JPG

http://www.v8tvshow.com/1965_Impala_...1.17.14_26.JPG

The floor opening was increased for the transmission and Quicktime bellhousing.

http://www.v8tvshow.com/1965_Impala_...1.21.14_02.JPG

A loose cardboard mock-up was made to get an idea of the shape of the tunnel. This car will be running a stock 1965 Impala console, so a mounting surface was required for that as well.

http://www.v8tvshow.com/1965_Impala_...1.22.14_05.JPG

The new tunnel was made and welded in place.

http://www.v8tvshow.com/1965_Impala_...1.23.14_06.JPG

A few ribs were added to strengthen the firewall at the tunnel.

http://www.v8tvshow.com/1965_Impala_...1.24.14_07.JPG

Now we had plenty of clearance for the transmission.

http://www.v8tvshow.com/1965_Impala_...1.24.14_12.JPG

Next, the new transmission tunnel was fit to the original SS floor console.

https://lh3.googleusercontent.com/-l...2.03.14_20.JPG

https://lh3.googleusercontent.com/-J...2.04.14_01.JPG

After the new console mounting brackets were made and installed, a considerable gap existed between the side of the console and the transmission tunnel, so a new base was made out of fiberglass to fill the void.

https://lh3.googleusercontent.com/-8...2.04.14_03.JPG

https://lh3.googleusercontent.com/-i...2.04.14_05.JPG

Wire framing was used to form the shape.

https://lh3.googleusercontent.com/-L...2.04.14_07.JPG

Fiberglass matting and resin was used to make the structure.

https://lh3.googleusercontent.com/-k...2.04.14_09.JPG

With the seats in place, and the new base sanded and primed, the gap is now filled.

https://lh3.googleusercontent.com/-l...2.05.14_09.JPG

This will be covered with carpet when finished.

A few questions about transmission setup.

Did you run viper to ls bellhousing and turn input down, or convert front plate and input to LS?

Also, what are your plans for speed sensor?

Thanks