Lateral-g Forums - PSI Conversion

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)

- LSX Conversions (https://www.lateral-g.net/forums/forumdisplay.php?f=70)

- - PSI Conversion (https://www.lateral-g.net/forums/showthread.php?t=50836)

Hooked up a NOID light this AM. The light comes on then never comes back. Seems like the injectors only get a signal for a second then goes away. I have sent the ECU back twice. I have a guy coming over Sunday to hook it all up.

We have added grounds everywhere. Cleaned off metal so its a good contact.

Ckeck the ignition relay on the psi fuse box.

Switch it with the fuel pump relay and see if the noid light works.

Pull the relay and check that you have 12v to it key on and when cranking.

Quote:

Originally Posted by Vega$69 (Post 618694)

Ckeck the ignition relay on the psi fuse box.

Switch it with the fuel pump relay and see if the noid light works.

Pull the relay and check that you have 12v to it key on and when cranking.

Thanks for all the help. I just sent my Dad a text for him to try it. I will keep you posted.

She runsssssssssssssssss

Instagram. Jayswiz

Quote:

Originally Posted by Swain (Post 618730)

She runsssssssssssssssss

Instagram. Jayswiz

Congrats Jay.

Come on man. What was it?

Inquiring minds want to know.

Quote:

Originally Posted by Vega$69 (Post 618735)

Come on man. What was it?

Inquiring minds want to know.

Still gotta figure it out. I tried a little starter fluid and it fired right up. It won't start unless you spray just a tad. So maybe it needs a little start up tune

714-345-3875 text if ya wanna here a short clip

Sounds like you do not have proper ECM voltage while cranking. Have you measured the voltage with a meter while cranking etc?

Don

Quote:

Originally Posted by Swain (Post 618683)

My Ls3 does this. When I initially turn the key to run, the noid light flashes for like a 1/2 second. At crank it doesn't flash, but when the motor fires, it begins to flash constantly. I have no starting issues and am running an E38 with Corvette regulator (return less).

Quote:

Originally Posted by cpd004 (Post 618758)

Corvette regulator (return less).

Corvette reg does have return to tank at the regulator.

Quote:

Originally Posted by Vega$69 (Post 618762)

Corvette reg does have return to tank at the regulator.

I meant returnless at the rail...thanks!

Quote:

Originally Posted by cpd004 (Post 618763)

I meant returnless at the rail...thanks!

Yep. Much better way then to return fuel from the rails that has been heated as it passes through the engine bay.

I know I'm super late to this party, but I don't have my wires for the TCC pedal hooked up either. Runs just fine. Like mentioned, the #1 reason for not firing is the constant power to the ECM while cranking.

I ran my ECM power from the HEI power wire.

Quote:

Originally Posted by Vega$69 (Post 618622)

You don't need any additional relays or diodes.

I've done 5 LS swaps on 1st Gens all with factory ign switches. 3 GM Perf Harness, 1 Psi and 1 reworked GM take out harness.

LS ECM

You need 12v switched power to the PSI fuse box.

The ECM is powered up with ign 12v. When you turn the key on the ignition and fuel pump relays close.

When you hit start the purple wire provides 12v to the starter.

From PSI

NO-START
1. Red Ignition Wire (From back of Fuse/Relay Center) has 12-volts with the Key in the ON
position and CRANKING position. This cannot be stressed enough, most NO-START
conditions can be traced to this wiring issue.
2. Check that 2 Large Ring Terminals by Crank Sensor are connected to CONSTANT POWER.

Batt. Battery Positive (2 LARGE RING TERMINALS COVERED IN BLACK HEAT
SHRINK), These are often mistaken for ground wires because of the black heat shrink

You hit the nail on the head here! I just started mine for the first time this evening. Got everything wired up (harness and ECM from PSI as well). Wasn't getting juice to the fuel pump wire (87 slot on relay). Come to find out I had tied those two Battery Positive wires to the block as grounds not to the starter as required. Car starts and runs now but won't idle. Not hijacking this thread so I'll start my own but am subscribed to this one.

That stinking starter lug wire. One of the reasons I don't like the PSI harness.

Quote:

Originally Posted by cjsgarage (Post 620676)

That stinking starter lug wire. One of the reasons I don't like the PSI harness.

It would help if the wire was red! HOWEVER.....my fault for not reading the instructions clearly.