The temps have finally dropped in the South - and I wanted to get the SS to the track one more time before the crap weather starts dropping.

So I took the SS to my local 1/8th mile drag strip - and ran the fastest time ever!

For all my runs - please watch the video below:



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In my latest project/video - I go over on how to add factory bluetooth to your Sierra/Silverado.

You will need the VCIM computer out of a 2009 TrailBlazer to swap into your car. You will also need the Bluetooth Anttena that attaches to the VCIM .

You will need to remove the top of the dash to get to the VCIM box, and fabricate your own bracket to mount it to the dash.

Plug everything in - and you will be good to go.




Parts Used:
2009 Trailblazer VCIM Box: 20830941
Bluetooth Antenna: 15938939 http://amzn.to/2sRXHEP
Aluminum Sheet Metal for adapter bracket.

Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrushers

In my latest video - I start to tackle another issue with my truck.

I had been getting a Service Airbag System warning light on the dash - as well as the Drivers Information Center.

I did some research - and it turns out that these trucks and the SUV's of the same era like to have front impact sensors that go bad.

The sensors like to corrode because they are under the truck in the harsh weather conditions.

To fix this error - you need to disconnect both batteries, drop the skid plate, and replace the Front Impact sensor.

Parts Used:
Dorman Sensor # 590-204 http://amzn.to/2s1RAuE



Thanks everyone for all of your support!


Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video - I attended the Detroit Speed Open House in Mooresville, NC.

I filmed a bunch of the cars that where outside.

I also took a bunch of pictures of the cars that where in the shop - and have included them in this video.

Overall the Open House was a good time, and it was fun seeing the latest and greatest projects at Detroit Speed!



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video I modify a set of coilover extender adjusters.

I bought a set of universal adjusters that I thought would bolt on to my Pfadt Racing coilovers.

After initially looking at the adjusters - and my coilovers - I had to figure out how to make them work.

In this video - I show you what you need to modify to get these to work on your Corvette.


Tools / Parts Used:

Tap and Die Set: http://amzn.to/2kL0NZn
#30 Drill bit: http://amzn.to/2zlueEu
Set Screw: http://amzn.to/2z62TFp





Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video - I install the modified coilover adjusters from the previous video.

The install went pretty seemless - I had to remove the coilovers from the car, install the new adjusters, install the coiloivers and slip the adjuster knobs back onto the adjuster.

Tools / Parts Used:
Tap and Die Set: http://amzn.to/2kL0NZn
#30 Drill bit: http://amzn.to/2zlueEu
Set Screw: http://amzn.to/2z62TFp



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video I install a Flex Fuel sensor on my 2005 Chevy Corvette.

As part of the build - I am going to add an E85 tune to the car - but I want to be able to still run pump gas.

So in order for this to work - I picked up a flex fuel sensor from DSX tuning - and installed it.

Tools Used:
Fuel Line Quick Disconnect Tool: http://amzn.to/2zDRf9h




Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video I wire up the Flex Fuel Sensor that we swapped in last week.

I show you how to run the wire - remove the harness from the pcm - and what pin needs to be added to the stock computer.

Parts/Tools Used:
1/4" Wire Loom: http://amzn.to/2htLe3P
Duplicolor Rustbarrier Paint: http://amzn.to/2APA3uz
Panel Clip Pliers: http://amzn.to/2hBGBZa
Push Pin Pliers: http://amzn.to/2yJ1Dsd



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video I install the Hobbs Switch into the Edelbrock Supercharger - as well as start on the wiring of the external fuel pump system that I will be running.

Link to CorvetteForum Wiring Harness Thread:
https://www.corvetteforum.com/forums/...

Tools / Parts Used:
Weatherpack Crimper: http://amzn.to/2jiv918
Weatherpack Connector: http://amzn.to/2iIboka
DeatschWerks Fuel Pump: http://amzn.to/2iHUMJw
Bosch 5 Pin Relay: http://amzn.to/2hLwqOe



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

In this video I install the new external fuel pump for the Corvette.

I needed another fuel pump to provided the additional fuel requirement that the Corvette will need when running E85.

Tools/Parts Used:
Rivet Gun Rivnut Installer: http://amzn.to/2i3Bcqx
Step Bit: http://amzn.to/2i2Q5t0
Push Pin Pliers: http://amzn.to/2jwHcIj
Trim Removal Tool: http://amzn.to/2k9jAhc
Center Punch: http://amzn.to/2zPfq58
Air Drill: http://amzn.to/2i1mVdE
AN Wrench: http://amzn.to/2jv17ri



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss