Lateral-g Forums
Page 5 of 17 « First 34 5 6715 Last »
Show 40 post(s) from this thread on one page

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)
-   Project Updates (https://www.lateral-g.net/forums/forumdisplay.php?f=16)
-   -   '08 All Wheel Drive Denali (https://www.lateral-g.net/forums/showthread.php?t=27666)

boonedog 10-19-2010 08:42 AM
very nice work:thumbsup:

pacificustoms 10-19-2010 02:21 PM
Building a border to go around the engine compartment to fill in the dead space between the factory lip of the fender and the inner fender that we're building.

http://i55.photobucket.com/albums/g1...alismall97.jpg

Here's a panel we built as a fender filler piece to go between the firewall and fender lip. The dimpled holes and mesh are just dress up pieces and have a backing plate to keep water and debris out of the door jam.

http://i55.photobucket.com/albums/g1...alismall99.jpg

tones2SS 10-20-2010 11:21 AM
Awesome work Robbie!:thumbsup:

1Bad68Cat 10-20-2010 11:48 AM
Quote:
Originally Posted by pacificustoms (Post 311374)
Gas tank built from scratch with all of the evap stuff from the original tank. We decided to keep everything GM put in the car, that way it's as close to "stock" as possible. We even re-used all of the plastic lines by heating them slightly, bending them and letting them rest in their new form. If you have a lot of patients, it isn't that difficult to do.

http://i55.photobucket.com/albums/g1...alismall73.jpg

http://i55.photobucket.com/albums/g1...alismall74.jpg

http://i55.photobucket.com/albums/g1...alismall75.jpg
Do you sell the fuel pump module mouting hardware? I plan to build the tank for my 66 c10 and would like to use the factory fuel pump that came with the ly6/6l80 I picked up. Also, what do the connections on the fuel pump module go to? I assume the large line is fuel feed, medium is tank vent, and the small is the EVAP.

Thanks,
Robert

pacificustoms 10-20-2010 02:13 PM
Any machine shop should be able to make you some. We machined them up ourselves for it. With your fuel pump we could machine some for you. I'm pretty sure the big one was the feed and both others went to evap. We just kept all the plastic lines and re-bent them around to all of the factory evap equipment. They do make adapters to clip onto those lines at the fuel pump and adapt to male AN fitting as well.

1Bad68Cat 10-20-2010 02:26 PM
Quote:
Originally Posted by pacificustoms (Post 312148)
Any machine shop should be able to make you some. We machined them up ourselves for it. With your fuel pump we could machine some for you. I'm pretty sure the big one was the feed and both others went to evap. We just kept all the plastic lines and re-bent them around to all of the factory evap equipment. They do make adapters to clip onto those lines at the fuel pump and adapt to male AN fitting as well.
Sent you a pm. Buy the way, great work on the fabrication.

Robert

pacificustoms 10-20-2010 03:16 PM
Thanks!

We fabricated a piece to go across the front to cover up all the ugly in the front of these things.

http://i55.photobucket.com/albums/g1.../DSC_00103.jpg

http://i55.photobucket.com/albums/g1.../DSC_00084.jpg

Machined our own hardware to hold it down. We wanted something really streamline as there isn't much hood clearance in the area.

http://i55.photobucket.com/albums/g1.../DSC_00064.jpg

Made matching pieces for the hood adjusters

http://i55.photobucket.com/albums/g1.../DSC_00043.jpg

War 10-20-2010 03:36 PM
That's very nice clean work.

coolwelder62 10-20-2010 04:07 PM
WOW!!! Robbie,Awesome fab work,over the top engineering.:thumbsup: Scott

conekiller13 10-21-2010 02:39 PM
Very high quality stuff there.....those welds are making wish I had 100th that skill.....


All times are GMT -7. The time now is 02:37 AM.
Page 5 of 17 « First 34 5 6715 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright Lateral-g.net