Twins are good. :unibrow:

Great! We're ready anytime you need us!

Will I have the CENTER FORCE setup for my car I'm hearing good things!!

I think I got pretty close.
http://i.imgur.com/frDYlGk.jpg

http://i.imgur.com/kFWQNFu.jpg

I ended up making game time decision on adding a 4th button on bottom.

Still need to cut in the AC control then pull it all apart to paint it. Happy with how it's looking so far though!

VERY nice
 

Will, fantastic work ... I'm right behind you on the new dash setup and watching closely. Also, thanks for the heads up on the Modo door popper installation.

Cheers
Steve

Well fuse panel got mounted in the vintage air "shallow" glove box included in the kit.
http://i.imgur.com/b3zQQkD.jpg

http://i.imgur.com/eT6YmJG.jpg

http://i.imgur.com/68F81UP.jpg

http://i.imgur.com/qgL8zRm.jpg

Prob is there was no room for the massive Holley Dominator ECU.
http://i.imgur.com/5pgLMWU.jpg

So I decided only solution was to attempt to build a mount for the fuse panel and holley ecu. First stab at it i think looks ok, it serves as a new glove box, and was built with very minimal tooling.
http://i.imgur.com/cFq6qQR.jpg

http://i.imgur.com/sS97fcK.jpg

http://i.imgur.com/MULyLn6.jpg

http://i.imgur.com/WGbrwLw.jpg

http://i.imgur.com/JDhaKIt.jpg

http://i.imgur.com/O7cmman.jpg

http://i.imgur.com/NUUiwa1.jpg

http://i.imgur.com/ZOF7L6K.jpg

http://i.imgur.com/8lcXxkF.jpg

http://i.imgur.com/QqH750f.jpg

http://i.imgur.com/cKGH4YY.jpg

http://i.imgur.com/hj9sftW.jpg

It looks good Wil, nice job.

More work this weekend.

Took a break from the metal work and decided to modify the tail light buckets for the LED panels. Overall not too bad but the brackets that are included fit like ****.
http://i.imgur.com/Ola3gGn.jpg

http://i.imgur.com/5TdFmON.jpg

Then decided to put the glovebox in the car and check fit and begin wiring (you can see rear light wiring already run to the trunk in previous picture.
http://i.imgur.com/63jXgGd.jpg

http://i.imgur.com/4NOZCJE.jpg

Also ran the pain power cable. 2/0 welding cable. Pretty intense stuff and a beastly crimper needed to attach the lugs.
http://i.imgur.com/9UwOWaZ.jpg

http://i.imgur.com/4AeJvdV.jpg

http://i.imgur.com/zlZDP4p.jpg

http://i.imgur.com/EBZKpFO.jpg

Picked up a product called Shine Seal from the original founder of Zoopseal in an effort to seal the raw aluminum I have in the engine bay. I cleaned all these panels and lightly brushed with a 3m pad.
http://i.imgur.com/Jpk4BVU.jpg

http://i.imgur.com/BVppvze.jpg

Did the reservoirs also.
http://i.imgur.com/Mjs92ZA.jpg

Lastly I started working on the Holley wiring and making good progress for a short amount of time. I hope to have this harness completed and modified for my setup by this weekend. Hope I can find the time to hit the garage hard this week.
http://i.imgur.com/4hsdXk8.jpg

http://i.imgur.com/3vK9skR.jpg

Test fitting intake and verifying lengths of harness.
http://i.imgur.com/Y4DGV3r.jpg

William

Wow
 

Great work William, Looking good, :gitrdun: