Lateral-g Forums - This is MY 67 Camaro

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)

- Project Updates (https://www.lateral-g.net/forums/forumdisplay.php?f=16)

- - This is MY 67 Camaro (https://www.lateral-g.net/forums/showthread.php?t=34830)

Michael, Your doing a great job. I hope the trans bracket worked to solve the problem of trans crossmember tab being a little short(and the tig welds looked OK) . I based That bracket length off info & 4L60E measurements I got from the auto recycle yard.Sorry for the inconvenience.:thankyou:

Quote:

Originally Posted by KPC67 (Post 585251)

looking good chief! keep at it.:thumbsup:

:thankyou: Keeps me outa the bars!

Quote:

Originally Posted by waynieZ (Post 585256)

Looking Good! The trans mount came out nice.

:thankyou: Scott did a great job fabbing, and then I welded it to the xmember. Its installed finally!

Quote:

Originally Posted by bsharpe (Post 585272)

i have been watching this thread closely. I am putting scott mocks subframe and ridetechs 4 link under my 71 trans am clone.

I understand why your are frustrated with the 4 link fitment. I was surprised with issues with the subframe and 4 link. try using the directions to install the 4 link on a ford 9 inch. None of the brackets fit.

Keep up the good work and keep posting your progress. it is appreciated.

I read your thread .... everything is fine here, I can't go much lower than 27" and then I don't have any travel left. So .... I'm gonna raise the trunk above the diff and clearance the sway bar mounting bar some.

There's always more to come :thankyou:

Quote:

Originally Posted by SlowProgress (Post 585340)

Looks like you are moving along. I need to copy your work ethic ! Beautiful day out in the garage in Phoenix !! :thumbsup:

When time is precious you gotta get going and make a goal to finish something!

Quote:

Originally Posted by coolwelder62 (Post 585387)

:thankyou: Scott, that bracket was great! I will get you the measurements from bell housing to mounting bolt center one of these days .... I'll put it on my list!

Thanks for looking ....

Keeping warm by the

Quote:

Originally Posted by grendel (Post 585443)

Looking good.

Thanks JJ .... keep picking at it and it will be done!!

welder the last two days! Wanted to get the RT brackets welded on the 12bolt before it got too cold to be in the garage. Measure 12 times and weld once, came out good, I think its only a 1/16 off in the C2C mesurement!

In hindsight I should have moved the Camaro further into the garage before I put it on jackstand .... I didn't have much room to work on the axle, but it keep the heat isolated :confused59:

http://imagizer.imageshack.us/v2/102...540/uGhNLH.jpg

http://imagizer.imageshack.us/v2/102...540/x0P4ey.jpg

http://imagizer.imageshack.us/v2/102...540/NuCUcz.jpg

I wish everyone a Happy Holiday!!! Cherish the times spent w family and friends and remember those that are serving our country and can't be with their family and friends :military:

Thanks for looking ... see ya!

Michael

Quote:

Originally Posted by Sonar Chief (Post 586202)

Looks great Michael , can't wait to see it on all fours. Merry Christmas to you too!
Kevin

Merry Christmas to you and yours as well Chief, Thank you.

Great pictures of great looking brackets, I like the little Ridetech symbols laser cut in them. That's a cool detail I had not previously noticed.

Merry Christmas to you and your family Chief. Its looking good.

Merry Christmas Micheal,I wish I could weld that nice,looking good:thumbsup: :thumbsup:

That's looking really good. And to continue the theme have a Merry Christmas !

Quote:

Originally Posted by SlowProgress (Post 586386)

That's looking really good. And to continue the theme have a Merry Christmas !

+1. And Merry Christmas.