Really starting to come together now,top notch fab work all the way:thumbsup: :thumbsup:

Thanks... its time consuming to get it right!

I thought it was better than duct tape :lostmarbles:

So I use the same clamps from HF so I made up something similar .... works good thanks for the tip!!

Thanks ... your car is awesome!

Thanks, the fitment is really close and that makes it a whole lot easier to fine tune!

Here is some pixs, still need to fine tune the angle for the main hoop (85 degrees) and bend the plates for the floor.

http://imagizer.imageshack.us/v2/102...673/foQxAr.jpg
Made some clamps to hold her in place!
http://imagizer.imageshack.us/v2/102...661/kIIQ6c.jpg
Rear window is in place ... plenty of clearance!
http://imagizer.imageshack.us/v2/102...661/k5JFsg.jpg
Kickers tuned to fit the connectors!
http://imagizer.imageshack.us/v2/102...911/1HBsPg.jpg
Better view ... looking cool!


There's tomorrow for the rest (1) fine tune the trunk drops (2) bend all the plates to fit (3) get help to take off the roof so I don't taco the roof (4) start welding!!!!

This is time consuming to get it fit really nice, but it's paying off fer sure!

Thanks for looking ....

It looks good!

Cage looks really good, nice work. Just a note, if you think there may be some racing in your future with NASA or SCCA, you might want to take a look at the rules for the cage before you finish up. For a race spec cage, the rear downbars can not have any bends in them for instance.

Too nice to be inside!
 

Thanks Wayne .... since you have a Nor'easter and we are 70 degrees I would do a little color selection and get outa the garage.


Thanks for the heads up .... I don't plan on any racing the Camaro in classes, just being prepared for the worst and the best handling I can get!


So, since its so nice out I figured I'd spray some color and narrow down a color choice .... not an easy task fer sure.

Anyway, here is a matte blue that is interesting, I might try a grey also ...
The extension was not body shaped, just in primer, the dent will buff out :lol:
http://imagizer.imageshack.us/v2/102...673/I3FLb3.jpg

http://imagizer.imageshack.us/v2/102...537/ug94BK.jpg

http://imagizer.imageshack.us/v2/102...909/0BclPJ.jpg

http://imagizer.imageshack.us/v2/102...537/K4HA4F.jpg

What dent? :warning:

hehe

Man, can't believe the progress you have been making. It is always good to switch channels and do some painting to kind of unwind after being neck deep in fabbing, and other demanding parts of a project.

Good day
 

Hey that dent, your are right about taking a break from fabbing ... and thanks!

Well, picked a couple more colors today and sprayed the extension again ... the grey is alright but the blackblue may be the ticket.

Got the roof off, fabbed up the floor plates, cleaned all the mill scale and rust off the roll bars ... looks kick azz in brushed, may just clear over this!!

Gonna work on the truck plates, had to put in the tubs to check clearance ... then some heat!

Take a look ...

http://imagizer.imageshack.us/v2/102...537/SE87Xz.jpg

http://imagizer.imageshack.us/v2/102...540/3lDxAk.jpg

http://imagizer.imageshack.us/v2/102...540/dyk2hb.jpg

http://imagizer.imageshack.us/v2/102...661/v5Aph5.jpg

http://imagizer.imageshack.us/v2/102...911/nti1ac.jpg

http://imagizer.imageshack.us/v2/102...909/yXYt0h.jpg

More work tonight after dinner, gotta mock the trunk bars and bend the plates ..... there is always something!

Thanks for looking ....

Your moving right along. It looks good.

Good progress! Progress is good! Progress on almost anything helps to motivate.

One of the things I tend to do is think something is going to be hard - or that it'll take a lot of figuring.... but if ya just pick up a tool - and do something - whatever "it" was that you thought was going to be hard usually isn't. LOL

Thanks Wayne .... how much snow you get?


Well said, most times it looks hard and if you don't get out in the garage and try .... it never gets done!!!!

Trying to get as much done before my next classes start here in Feb .... steady the course.