Lateral-g Forums

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)
-   Cooling: Radiators/Fans/Controllers (https://www.lateral-g.net/forums/forumdisplay.php?f=89)
-   -   PWM cooling fan(s) control using ECM (https://www.lateral-g.net/forums/showthread.php?t=40215)

parsonsj 08-16-2013 07:47 AM

The AC-Delco pn is 15-80803 if that means anything.

parsonsj 08-18-2013 08:33 PM

I talked with a local tech today who does a lot of late model upgrades. He said that on C6s they routinely swap to dual Spal fans and get another fan controller and split the signal line from the ECM with great results.

So it seems a single controller with dual fans and dual controllers splitting the signal both work fine.

samckitt 08-19-2013 08:55 AM

Quote:

Originally Posted by parsonsj (Post 499210)
I have found this site.

http://www.obd2allinone.com/sc/details.asp?item=m5j3

Looks like you can pick up the connectors there. 10 / $2.95.


Here is another site to get the terminals from:

http://www.eficonnection.com/eficonn...spx?ItemId=314

Downside is you have to have a $25 minimum order.

JMitch19 08-19-2013 02:03 PM

Quote:

Originally Posted by samckitt (Post 500010)
Here is another site to get the terminals from:

http://www.eficonnection.com/eficonn...spx?ItemId=314

Downside is you have to have a $25 minimum order.



mouser.com also has the ecm terminals. A lot of sites call them Delphi connectors but they are really molex. The molex pn is 33467-0005 minimum quantity 1.

http://www.mouser.com/ProductDetail/...TgQDO3tTBTM%3d

parsonsj 08-19-2013 02:10 PM

Excellent! Can you find the cavity plugs? I just spent 5 minutes on Mouser without any luck...

JMitch19 08-19-2013 02:30 PM

Quote:

Originally Posted by parsonsj (Post 500072)
Excellent! Can you find the cavity plugs? I just spent 5 minutes on Mouser without any luck...

Most of the the work that I have done has been will GM's E38 ecm. Below are the two connectors for the E38. They don't seem to list a cavity plug at all. I have completely stripped a few factory GM harnesses any I've never seen a cavity plug in a factory setup either. There is a build in seal in the connector that seals around the wire when you insert it. The wire openings in this seal are very small. You could just cut up some scrap 20/22 gauge wire and insert it in the unused spots.

http://www.molex.com/molex/products/...P_HOUSINGS.xml

http://www.molex.com/molex/products/...xml#partdetail

parsonsj 08-19-2013 02:40 PM

No, there's a cavity plug in the harness. They look like this:

http://www.eficonnection.com/eficonn...plug_mx123.jpg

JMitch19 08-19-2013 03:15 PM

Quote:

Originally Posted by parsonsj (Post 500074)
No, there's a cavity plug in the harness. They look like this:

http://www.eficonnection.com/eficonn...plug_mx123.jpg

Looks like I just needed to work a little harder... http://www.mouser.com/ProductDetail/...ff%2fQDg%3d%3d

I have a completely stock GM L92 harness sitting right next to me which has no factory cavity plugs. It's good to know these are available.

parsonsj 08-19-2013 03:17 PM

Awesomeness! Thanks very much. I'll ordering up some tonight.

samckitt 08-19-2013 07:22 PM

Pretty sure this is one of the connectors, but I think it is the one that goes to the fan, not the fan module itself.

http://www.casperselectronics.com/st...2fb0a1b1b04209

http://www.eficonnection.com/eficonn...spx?ItemId=915


All times are GMT -7. The time now is 01:12 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright Lateral-g.net