Ken
Yes if you don't mind please send it to me. I would like to try to see if it will work for me.

Thanks
Bill

I picked up the rear axle assy today from Chassis Service......Powder Coated.....and everything new including axles....Jimmy installed the rear brakes at the same time..........

Saved me some time..........Brought it home and mounted the Ridetech rear Coil-over brackets and just kept going.....got it installed.......Also got the new motor mount engine adaptor plates and frame mounts finished......the adaptor plates worked perfect.....but ....I have to modify the frame mounts to fit the rubber mounts.....I should of had one at the shop to check what I was making........LOL.......



http://i13.photobucket.com/albums/a2...ps159dc025.jpg


http://i13.photobucket.com/albums/a2...psffce893e.jpg


http://i13.photobucket.com/albums/a2...ps5e493daf.jpg


http://i13.photobucket.com/albums/a2...psee3f537e.jpg


http://i13.photobucket.com/albums/a2...ps0cd84098.jpg


http://i13.photobucket.com/albums/a2...ps86a6cfd4.jpg


http://i13.photobucket.com/albums/a2...ps3f6b0a95.jpg


http://i13.photobucket.com/albums/a2...ps97d19dc9.jpg


http://i13.photobucket.com/albums/a2...ps6e9ce5b1.jpg


Ken

Very nice!

Got the new motor mounts finished and installed today.........As you can see in the first picture the Dirty Dingo slider mounts on the stock frame stands were up to the front of the engine.........I needed that room on the passenger side for the A/C compressor......so....the slider adaptors and the frame mounts had to go............in the following pictures you can see the new adaptor plates and frame mounts I made to shift the mount position to the center of the crossmember to give me the room for the compressor.........I made a couple of simple mounts and a RH/LH heim end tensioner to get the stock belt tight.......I also made some new brake lines at the master cylinder with the coil in them for body/Chassis flex (thanks Rick).......Getting ready to pull the engine out for the last time for a couple of loose ends then it go's in to stay.....


http://i13.photobucket.com/albums/a2...ps4a07fc3c.jpg


http://i13.photobucket.com/albums/a2...ps6e9ce5b1.jpg


http://i13.photobucket.com/albums/a2...ps3c6d9ab2.jpg


http://i13.photobucket.com/albums/a2...psc7c1f656.jpg


http://i13.photobucket.com/albums/a2...psa2e13b60.jpg


Ken

Got the Brake lines finished up today and bled the brakes also......Didn't do too bad.....had about 13 brake line connections and only had 12 leaks..........Another thing off the list....


http://i13.photobucket.com/albums/a2...psefcf576e.jpg


http://i13.photobucket.com/albums/a2...ps73651bc1.jpg


Ken

nice work 12 out 13 not too bad lol got my eye on you lol

Well.........It seems that me and the rear brake God have some issues......Complete Wilwood system including Master Cylinder.......I bench bleed the master and had to "Work" it to get the rear system bubble free.........the front cleared up with a couple of pumps.........So.....everything installed (all new brake lines)and gravity bled till I got some help to finish the job........Bled the fronts and when opening the bleeder valve it was like a water fountain and the pedal went to the floor as it should.......Great!!......go to do the rears and I would get a couple of drops and the pedal stayed right where it was......Hummm!!!.........either side didn't make a difference.........Hummmm!!!............So....I'm thinking maybe the adjustable proportioning valve is the issue......so I crank it in to give it maximum flow........go to bleed them again......same thing ......a couple drops of fluid without any pedal drop.......So......I call Wilwood and talk to one of the tech guys.........After conversation with them I learned that even with the proportioning valve at full flow.....it only allows 57% of volume thru......so......Today I decided to remove the prop valve..........while I was making a new brake line I decided to do the bench bleed again.....after removing the brake line I put my thumb over the port and worked the pedal thru the steering column hole.....I got some pressure but not enough to blow my thumb off the port......Hummm!!!.......So.....I finish up and install the new line and again....in bleeding the rear I just get a couple of drops with no pedal drop...............Am I missing something???.......It would seem to me that the M/C even though new could be bad....


On another note.....I ordered the wheels today...........and tomorrow I should receive the balance of my Dakota Digital order so I can continue on with the wiring.........I also got all the belts installed and tensioned correctly.........And.....In checking out the pan clearance with the steering arms......It seems I not going to have any clearance issues......(But...the suspension is still unloaded).......


http://i13.photobucket.com/albums/a2...ps6d68cdc1.jpg


http://i13.photobucket.com/albums/a2...psd755e310.jpg

What did you decide on for wheels?

http://i13.photobucket.com/albums/a2...l-0190_sml.jpg


Grey Powder Coated center and Brushed rim

I would be interested to know what your passenger side head to firewall clearance is. Those AC brackets look very similar to the Alan Grove components that mount a Sanden 508. I am beginning to think I could possibly make those work without notching the frame.