|
Quote:
I need to do some rule diving again... moving the wing back might help, but C3 Corvettes get nose light - so moving the point where it's pushing down further back might not be a good idea on the track.... wonder if they'd notice if I swapped struts between the track session and the autox.... |
well, look what's back?
https://i.imgur.com/TBXMJg4h.jpg dark bronze https://i.imgur.com/70Syb4ih.jpg fuel cap too https://i.imgur.com/T2ebVsuh.jpg I like. a lot https://i.imgur.com/kJ9Hqhyh.jpg truly better then I expected.... I thought I went too dark https://i.imgur.com/CxdmyFPh.jpg with the wing in place https://i.imgur.com/olBY9k5h.jpg |
a bit done tonight
more fittings - most important is that stainless one https://i.imgur.com/tMf7JcDh.jpg the problem is I welded a pipe fitting for the return when I needed an AN one... oops... will use it as a vent https://i.imgur.com/zFIBeUah.jpg and welded https://i.imgur.com/lotX6oeh.jpg in other news, I'm a really bad influence.... the red Corvette owner has bbc plans :) https://i.imgur.com/BI0f9HEh.jpg |
I think you picked a good color with the rims :thumbsup:
|
Looks great!!!
What color exactly are the wheels? I'm looking for a titanium/bronze color for my centers. Assuming they are satin cleared as well? |
Quote:
|
Spoiler is supported by the frame... I also put window glue in place to keep the warp and vibration transmission to a minimum
https://i.imgur.com/PBuKL2ih.jpg measuring done, time to make the tank support https://i.imgur.com/4VyOMYoh.jpg keep in mind I was about 150 lbs light for where I'm racing.... I'll probably gain 30 or 40 lbs in this... all on the correct end https://i.imgur.com/41BWO5Eh.jpg https://i.imgur.com/nk1HQETh.jpg framework installed https://i.imgur.com/MVeSTIuh.jpg not in love with the straps, however, I plan on supporting the defuser off them - so function trumps form https://i.imgur.com/wKSaKYkh.jpg up the tank goes - the metal duct tape was put in place to keep the fiberglass from sagging when I filled the holes for the luggage rack https://i.imgur.com/uzsDJASh.jpg very close - I wanted to make it solid but I wouldn't be able to get the fuel pump out if I did https://i.imgur.com/aOanwENh.jpg last test fit, next up with the fill neck, lines attached, electrical attached and rubber protection on the metal bands https://i.imgur.com/hlfDYEsh.jpg |
Splitter material... best source?
|
a little further
wheels with tires on them https://i.imgur.com/jeSZkNch.jpg cut down the fill neck so I can use a flexible rubber hose for the offset https://i.imgur.com/3EeXqeEh.jpg padding/rubber top and bottom https://i.imgur.com/zx8Tg4Gh.jpg getting close... waiting on a fitting and the fill hose https://i.imgur.com/zDH04cLh.jpg |
it runs again...
https://i.imgur.com/5BZ5wZ2.jpg interior is back in it https://i.imgur.com/PSWXy1m.jpg next up? front stuff https://i.imgur.com/zqSW4dl.jpg looks all buff in the back.... but more to do...thankfully, this isn't a take the car mostly apart deal https://i.imgur.com/YpF0RWP.jpg also need to program and do weighing |
| All times are GMT -7. The time now is 05:06 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright Lateral-g.net