Erod GTO at EBMC
 

OK, if your Pontiac purist you may want to stop reading now..........:mad:

We had a request to bring a customers 66 GTO up to mondern standards.After our Erod event a few months back, he decided this was the route he wanted to go. He desired a stock appearance with modern drivetrain suspension and all modern underhood. He purchased the car last year and was overall was a very clean, rust free car. We pulled the front sheetmetal and began the transformation.
[img]http://i864.photobucket.com/albums/a...0%20HP/142.jpg

[imghttp://i864.photobucket.com/albums/a...0%20HP/141.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/111.jpg
[img]http://i864.photobucket.com/albums/a...30%20HP/16.jpg
[img]

A few shots of the smoothed firewall. Vintage air will be installed.

[img]http://i864.photobucket.com/albums/a...20HP/008-1.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/011.jpg
[img]http://i864.photobucket.com/albums/a...0HP/0012-1.jpg
[img]http://i864.photobucket.com/albums/a...20HP/005-1.jpg

Speedtech suspensionand GTO coil covers adapted to LS3 also used Quick performance AC relocation

http://i864.photobucket.com/albums/a...%20HP/0072.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/013.jpg
[img]http://i864.photobucket.com/albums/a...%20HP/0033.jpg

Love the idea. Not a fan of how stock old musclecars look anyway so do it!!!!!!!

Very nice. Should handle and go a lot better.:yes:

Looks like a cool project. I like the GTO motor for the GTO.....

I think it's cool seeing the LS engines, with the GTO covers, under the hood of classic GTOs

Thanks guys! Afew more pics of ECM installed, brake system plumbed, DSE wiper motor and engine installed

http://i864.photobucket.com/albums/a...%20HP/0042.jpg
http://i864.photobucket.com/albums/a...%20HP/0052.jpg
http://i864.photobucket.com/albums/a...%20HP/0123.jpg
http://i864.photobucket.com/albums/a...0HP/0013-1.jpg

PM sent


Don't worry im not a Pontiac purist.

Killer Goat project Steve. I also love the new GTO valve covers on the old GTO! :thumbsup:

Nice....

Way cool.!!!:thumbsup:

Very nice. I'm going to have to pass by one of these days just for the hell of it and check out the shop.

Come on by anytime! (I'll give you a sneak peek at the SEMA bound Camaro's were doing.:_paranoid )

The car looks grreat its going to be a great set up.

looks good Steve, love the old GTO's, even better with modern mods!

We did not do a complete build on this car, so excuse the less than show quality floorpans and frame!

Ricks tank to corvette regulator, stainless lines to TFE lines at engine

[img]http://i864.photobucket.com/albums/a...0%20HP/072.jpg

crossmember mods for cat clearance

[img]http://i864.photobucket.com/albums/a...0%20HP/069.jpg

JTR tailshaft for mechanical speedo

[img]http://i864.photobucket.com/albums/a...0%20HP/067.jpg

exhaust started as an Edelbrock system but needed extensive mods

[img]http://i864.photobucket.com/albums/a...0%20HP/065.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/059.jpg

oil pan mods necesary for tie rod clearance

[img]http://i864.photobucket.com/albums/a...0%20HP/056.jpg

Nice looking, Your customer will enjoy that one

sweet car, will you have easy access to computer once the fenders are mounted?

Yes,its tight but there is plenty of room for computer
http://i864.photobucket.com/albums/a...0%20HP/014.jpg

Just about complete, need to do some trans tuning (4L65E w/TCI controller) and align.

[img]http://i864.photobucket.com/albums/a...0%20HP/202.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/204.jpg
[img]http://i864.photobucket.com/albums/a...0%20HP/206.jpg
[img]http://i864.photobucket.com/albums/a...%20HP/0014.jpg

Sweet work.

Is this a Dynatech V-Clamp? How do they hold up under use?
http://i864.photobucket.com/albums/a...0%20HP/065.jpg

Very nice. Engine bay looks great.:thumbsup:

i agree, nice looking!

Yes, they are dynatech clamps. We use them a lot and they hold up very well.
Thanks for the compliments everyone!

Looks great Steve. Perfect mods for that car.