MGB GT V8 project
 

Ok I finally settled on a project for myself.. I just picked up a 70 MGB GT that I will install my 302 and T5 tranny in with a disc brake ford 8.8 rear end in as well ...It should be a fun little ride... exterior wise I will install a Sebring body kit complete .. big wide rims and tires.. and low to the ground .. inside a full fabricated roll cage with racing seats and 5 point harnesses .. This will see plenty of track time..Pics on the way

Like this but in a dark blue with white stripes.I also have these slotted rims 15 x 10 inch wide i might use ..go old school
http://i158.photobucket.com/albums/t...twithslots.jpg

Very very cool! The ultimate go cart on sterroids.
Be sure and post lots of pics!

I always wanted a Sunbeam Tiger with a built V8 and 5speed.

That MG look's just like one that a guy I know named Phil had.He sold and built a Buick V8 powered MG race car.Cool.:thumbsup:

Before I had the opportunity to buy the Javelin I have now I was planning to build an MGB GT V8 much like what you were talking about.
Can't wait to see more.:thumbsup:

this is more like the look I am going for
http://i158.photobucket.com/albums/t...bluemgbGT2.png

:thumbsup:

That is going to be an awesome project! A few years ago, I dropped a small block ford V8 with an automatic in an early model TR6. What a ride! You are going to have fun with your project. Keep us posted on the build. I would love to see the finished car.

Arnold

Ok here is the starting point my 70 MGB GT in all its glory
http://i158.photobucket.com/albums/t...GTproject7.jpg
http://i158.photobucket.com/albums/t...GTproject8.jpg
http://i158.photobucket.com/albums/t...GTproject6.jpg
http://i158.photobucket.com/albums/t...Tproject10.jpg

Years ago, I used to have a 69 MGBGT. Loved the car, hated the motor. I thought of someday doing a project like this, but it was way above my mechanical ablities for the time. Please post your progress!

Ok the teardown begins and I am always amazed at what lurkes behind panels and under floor tar...so I will pos pics of all the areas hidden so if you were interested in buying one this is where you look..
Front Fenders removed
http://i158.photobucket.com/albums/t...ownbegins1.jpg
http://i158.photobucket.com/albums/t...ownbegins2.jpg
http://i158.photobucket.com/albums/t...ownbegins3.jpg
http://i158.photobucket.com/albums/t...ownbegins4.jpg

The floor pans are not so bad but i will replace both of them... remember this will be a street/ track car so i want it safe with out rust...
http://i158.photobucket.com/albums/t...ownbegins7.jpg

Ok here is the big question you are asking yourself..Will a 302 V8 fit in there....??????
http://i158.photobucket.com/albums/t...Tproject10.jpg

I say yes it will
http://i158.photobucket.com/albums/t...302v8mgbgt.jpg

Removed the drivers rusted out rocker... treated the whole inside with POR 15 and then installed a new full rocker ..you can see i have to cut off some of the front of the rear quater to do this ..then i just tacked it back on as it will get cut out fro the flares..
http://i158.photobucket.com/albums/t...kerremoved.jpg
http://i158.photobucket.com/albums/t...ivrockeron.jpg

Then I put a 17" wheel combo on the back ..not sure if it looks to big ..remembering it will get tucked under a flared fender....
http://i158.photobucket.com/albums/t...inchwheels.jpg