DSE Quadralink for 1st gen F-body, Corvette brakes
 

Time to clean things out!

I've got a Quadralink with a powder coated 9" axle housing with Moser 31 spline axles. The the axle housing and axles were run on my car before I switched over to a full floater. They have roughly 5,000 miles on them. The housing is powder coated black. It does have a scratch on it from being towed. If you aren't too picky, you can just touch it up with a little semi-gloss black.

All of the bracketry for the quadralink, i.e. control arms, mounting pockets, etc. are all brand new.

Asking $2,800 for this as is.

If you want a complete kit, that isn't a problem as Best of Show is a dealer for DSE and can provide whatever other parts you would like. Additional parts would sell at retail.

Also up for sale are brakes:
C6 Z06 brakes, front and rear. Powder coated gray. Asking $1200
C6 Z51 rear brakes. These brakes have less that 5 miles of use. I was test driving them when I got hit in the passenger fender: $400
Parking brake assembly for 9" with bracketry for C6 brakes: $300 - SOLD
I will throw in whatever brake pads I have on my shelf.

Will get pictures up soon,

Matt

PM Sent on brakes.

Matt, have pics of the parking brake setup for C6 9"?Will it work with ZO6 calipers?

Pm Sent

Pm sent on DSE stuff

PM sent

Send pics of quadralink and 9" to [email protected]

Thanks

I think I started everyone cleaning out their leftover parts lol! Between you, me and Steve there should be a lot more room in the shop by the end of the week lol! Please take pictures of everything and email to me - lol - j/k. GLWS.

Ok guys, I've gotten a surprising amount of interest today, so after I get pics up, I'll go back and figure out who inquired first and go by times just to be fair.

Here a few pictures, I'll get more tomorrow for the quadralink as most of it is boxed up right now.

http://i366.photobucket.com/albums/o...A/IMAG0275.jpg
http://i366.photobucket.com/albums/o...A/IMAG0276.jpg
http://i366.photobucket.com/albums/o...A/IMAG0281.jpg
http://i366.photobucket.com/albums/o...A/IMAG0282.jpg

Just to answer a few question and clear up a few things, first, the parking brake assembly will work for a 9" but could probably be used on a 10/12 bolt if Tobin will source the correct retaining plates. Second, the parking brake assembly will work for either of the rear brake setups.

Lastly, I never mentioned anything about shipping. All items will ship at buyer's expense. If you're in SoCal we can easily arrange pickup/delivery. I tend to drive around a lot.

Matt

I too am interested in the DSE. Add me to your list and I also would like to see photos.

Put me on the list for the z06 front/rear and the parking brake assembly. Just to verify if the rear end is the torino style ends? Do you take paypal?

Put me on the list for the dse stuff also

DSE quadralink
 

can you send pic of the dse parts to amd6769@comcast

z06 brakes
 

pm sent..

Sale pending on the Z06 brakes and e-brake assembly, as well as the quadralink.

The Z51 rear brakes are still up for grabs, and are ideal for anyone looking to do some track time that has a manual master cylinder. It should mitigate most of the effects of brake pad knockback.

Matt

Matt, PM'd ya.

Jeff

So the Z06 brakes with parking brake will bolt up to the dse front subframe and ford 9" with Torino ends? If so add me to the list and lmk how much i need to send

Quadralink and Z06 brakes are still for sale. I have a buyer interested in the Z51 rear brakes but they haven't sold yet.

Pictures of the housing:

http://i366.photobucket.com/albums/o...A/IMAG0285.jpg
http://i366.photobucket.com/albums/o...A/IMAG0283.jpg

Matt

Matt, im still interested in the parking brake assembly & the brackets.

PM'S ya.

Matt,
I was the first to post on this thread about the parking brake. Is it still available? If it is like the pm and post said I will take it.


Thanks

Are you selling just the axle housing shown, or does it include any of the control arms and other parts from the Quadralink?

Also, is that axle stock width, or narrowed?

We've got the housing with 31 spline axles and Torino ends (this was part of a complete assembly I ordered from DSE). measured from axle end to axle end, as in where the wheels bolt up, the rear is 54.75"

Also included are

upper link pocket assemblies
upper links
lower links
panhard bar
panhard bar body mount bracket assembly
all respective nuts, bolts, and washers.

Not included is the shock mounting shelf.

We can order any or all of the parts for a quadralink so it is as complete as you want it.

Matt

What's still for sale. Call

me 415 7203004

Matt,
Got the e-brake setup today. Thanks for everything!

No problem :thumbsup:

Sorry, I'll give you a call on Monday.

Currently the z06 brakes and quadralink are still for sale.

To make things simpler, I'm just going to throw in shipping for the quadralink. A couple people have asked for shipping quotes, and I can't give anyone an accurate quote without putting everything on a pallet and taking it down to get shipped.

Matt

What bolt pattern do the rear axles have and does it come with the backing plates and park brake shoes as in the photos? also what was your back spacing on your wheels? Also I have the DSE upper shock mount installed on an angle due to staggered shocks will this be a problem or does the mount have to be straight across? my wheels are 18x12 with 6.125 back spacing will this work? just to be clear it comes with everything except upper shock mount and diff centre section right?

Call me if u still have the quadralink . 415 7203004

Free shipping???!!! OMG - somebody else buy this before I do! I can't believe nobody has jumped on this killer deal yet! GLWS.
G.

Gregg, I would make an even better deal for you because I wouldn't even have to move the parts from one side of the shop to the other, let alone ship them.

Besides, we could always negotiate for one of those cool blue diff fluid catch cans :lol:

I'll get back to everyone by the end of the day. I might have found a use for the quadralink, and need to find if I should just hold onto it.

Matt

Dse stuff
 

Did you decide if you were going to keep it or she'll the dse stuff
If still for sell what else would I need to complete the quad link set up besides wheel tubs?? Thanks Shane