SBC PBM race block, 18 degree top end and headers for sale
 

Engine plans changed direction so these parts are up for sale. Local sale preferred especially on the big stuff of course. Will entertain shipping scenarios though.

PBM iron race block, 350 mains, 4.155 bore, .904 bushed lifter bores, splayed caps on all 5 mains, bored cam tunnel to BBC cam size of 50mm. machine work boring and diamond hone done by Watson Racing in Concord, CA

$1000 of fresh top notch machining. Asking $2000.

http://i236.photobucket.com/albums/f...8/photo1-7.jpg

http://i236.photobucket.com/albums/f...8/photo2-6.jpg

http://i236.photobucket.com/albums/f...8/photo-20.jpg

Callies Compstar 6.0" rods, small journal (2.00), 586 grams

Asking $525.

http://i236.photobucket.com/albums/f...oto_004-10.jpg

Callies Comet Lightweight 3.5625 stroke crank (43 lbs)

Asking $900.

http://i236.photobucket.com/albums/f...8/DSCF4094.jpg

GM 18 degree "363" heads, 47.5cc, 2.1x intake valves and 1.6x exhaust. Comes with springs but Watson encouraged me to get new PAC or similar springs.

Lift / Intake / Exhaust
.100 75 53
.200 149 106
.300 226 158
.400 264 212
.500 326 234
.600 358 247
.700 369 255
.800 373 258
.900 366 260
.975 366 262

http://i236.photobucket.com/albums/f...8/DSCF4011.jpg

Edelbrock 2922 intake for 18 degree heads, ported extensively by Wilson Manifolds

http://i236.photobucket.com/albums/f...8/DSCF4063.jpg

Jesel 1.7 intake/1.6 exhaust shaft rockers, Watson says a few of them need rebuilding but in overall good condition.

http://i236.photobucket.com/albums/f...8/DSCF4016.jpg

ARP 18 degree head stud kit

Top end kit (heads, intake, Jesel rockers, head studs) = $2200

Morel/Roush Yates .903 solid roller lifter, .180 intake offset.

$300

http://i236.photobucket.com/albums/f...8/DSCF3997.jpg

Stainless 18 degree stepped headers with merge collectors, 1-3/4" to 1-7/8" to 3-1/2" collectors, a few dings but came out of 8 second 1st Camaro with 421.

$375

http://i236.photobucket.com/albums/f...36cfe91d25.jpg


Parts are in the east bay of Bay Area currently. Email me at dwgordon at gmail if interested.

:cheers:

That's a good price on some nice parts :thumbsup:

Im passing this on to a buddy he's looking for 18* stuff.

Haha Skip! Gettin your inner Snoop Dog on :lol: :cheers:

Snoop Lion* now.. :lol:

Thanks Matt... forgot I have stainless headers with merge collectors available for these heads too. Fitment for 1st gen Camaro.

How much are you asking for the headers? I'm looking for some right now. Thanks, Pat

Hi Pat,

Info below also added to 1st post of this ad. Let me know if interested.

Stainless 18 degree stepped headers with merge collectors, 1-3/4" to 1-7/8" to 3-1/2" collectors, a few dings but came out of 8 second 1st Camaro with 800+ hp 421.

$375

http://i236.photobucket.com/albums/f...36cfe91d25.jpg

Great. Are the headers in Gilroy or Orinda? Ironically, I grew up in Orinda. It's a great place. I'm only 15 minutes away now so maybe I'll hear that new SB2 fire up at my house!! My car is in Campbell now at the shop so either Gilroy or Orinda would be fine. I need to see if they will fit my chassis but it looks like they will. Hopefully we can meet up this week or weekend if you have time. Thanks, Pat

jesus I just looked at the flow numbers again and these are creeping up on my sb2's well compare .900 to my .750 numbers...

teehee

FREE BUMP!

Matt

Hey Pat. Very cool. Loving it here.

The headers are in Gilroy but I'll prolly bring em back here soon since I now have a garage of my own!

Where is your car in Campbell? CAR?

The SB2 will be installed and dialed in down in Gilroy at my buddy Rich's shop. I do plan on scaring my neighbors a bit once it's ready to go. Altho I am a tad worried... my new neighbor is very bothered by a barking dog next door.... :lol:

We should meet up either way soon. Send me a PM with your info. :cheers:


Your SB2's should be over 400 cfm yeah?

Sounds good, I'll pm you so we can hook up. My car is at Blu808 in Campbell. Luke is a great guy and amazing welder. I'm going to need a shop for body and paint pretty soon so maybe I'll try your buddy in Gilroy.

418 @ .900

Ok package deal for $4500. Build yourself a bad ass pump gas 675 hp small block that will destroy those fat big blocks, or make it high compression and hit 725-750 hp and go full kill. :woot:


That doesn't suck. :unibrow:

Crank and rods sold.

PBM race block = $1700 ($2500 invested - brand new and fresh)

Top end kit = 18 degree heads, 2 intakes, Jesel shaft rockers, Morel lifters = $2000

Stainless Headers = $350

Headers sold.

Sale pending on PBM block.

Top end kit still available. Will sell as a package or piece out.

:cheers:

Top end kit price lowered to $1800.

Heads
2 intake
Jesel shaft rockers
Morel 904 lifters
APR head studs

:thumbsup:

Sale pending on top end package.