Scott Mock's Track ready1st. & 2nd. Gen Camaro C-6 sub frame's
 

I am getting ready to start another batch of sub frame's for those of you who are interested.I will selling them in 3 stage's Stage 1# $3400.00 W/O coil over's includes Shipping(lower 48) and will include the following part's.Bare welded frame,dropped bolt on steering arm's,complete hardware & shim kit,splined sway bar,arms,end link kit,ajustable upper coil mount.The stage 2# same as above W/Ride Tech Non ajustable coil over's $4050.00 shipped,Stage 3# all of the above stages plus New GM C-6 corvette componet's,Rebuilt Power rack & pinion,New Tie Rod Ends.$6400.00,You can add the following,New DSE power rack $500.00,Powder coat satin black $200.00,Gloss black $250.00,Drilled sway bar arms $75.00,Billet LS motor adapters $85.00,Poly mounts $75.00,Poly trans mount $35.00, billet P/S cooler and mount $85.00.Call me at 785-594-7481 or Email me at [email protected]ks Scott.(Ask about a Ride Tech or DSE rear suspension Kit or coil overs when you call about a Sub frame)http://i1104.photobucket.com/albums/...ps8715022b.jpghttp://i1104.photobucket.com/albums/...ps206d30b7.jpghttp://i1104.photobucket.com/albums/...psc29f7899.jpghttp://i1104.photobucket.com/albums/...psee07cf52.jpg:thumbsup: :thumbsup:

It looks great Scott! Your subframe is next on my list.

very nice stuff Scott! :thumbsup:

really cool scott. I'm really diggin the adjustable shock mount!

Looks like you could use a GMR package upgrade option! :D

Jason

Jason,The GMR up Grade's would be awesome.

I have a set of QA1's N/A & Ride Tech springs, that were orded for a customer who then up graded to full ride tech's.I am willing to throw these in with any sub frame ordered W/O shock's for $ 125.00 for the pr.w/ springs.:lateral:http://i1104.photobucket.com/albums/...nshocks008.jpghttp://i1104.photobucket.com/albums/...nshocks007.jpgSOLD!!!!!!!!!

Scott, I thought you were not making anymore Frames.

I have had a ton of folks as your self asking.So I desided it was in my best interest to keep building them.There are alot of people wanting my product.

Bravo Scott! Great looking mods. :thumbsup:

BTW, your shock mounts are what I was PMing you about. :cheers:

Ron,Would you like a set to weld to your chassis.

Track width
 

What would the track width be and max. wheel backspace?

Call you tomorrow Sir! :cheers:

The track width is 60.5 /o brakes,Max bs depends on wheel dia.

:cheers:

Thanks to everybody who have ordered.I have enough part's for 1 more unit left out of this run.:thumbsup:

Awesome! :thumbsup: Glad to hear people are still wanting these subframes.

A new unit ready to go out. http://i1104.photobucket.com/albums/...frame33006.jpghttp://i1104.photobucket.com/albums/...frame33005.jpghttp://i1104.photobucket.com/albums/...frame33004.jpghttp://i1104.photobucket.com/albums/...frame33003.jpghttp://i1104.photobucket.com/albums/...frame33010.jpghttp://i1104.photobucket.com/albums/...frame33011.jpg

Scott/All,
A little off topic, can someone point me to the sway bar used on this frame, and/or info on how it mounts in the tube mounted to the frame.

http://i1104.photobucket.com/albums/...frame33003.jpg

Thanks,
Scot

Like the newer engine mount design.... Very Nice Scott! :cheers:

looks like there would be plenty of crossmember clearance for the exhaust

The sway bar slide's inside the tube.Then a Bronze-oil lite bushing slide's over the bar,and inside the 1.75x.120 wall tube.Then the splined sway-bar arm's fit tight against the flange on the bushing.I designed it this way so the cross tube will serve as a forward crossmember giving added surport to the chassis.Thanks for Looking.

Does it ever need greased, or eventually replace the bushings?

Good design, I love it.

The bushing's are oil-lite.There is oil in the bronze.I lightly grease them as I assem.These only cost 9.80 each.So if they wear out, biggie.:thumbsup:

I'm good for one for a 2nd gen
PM me
I'd need it January of you can pull it off

PM,replied to.

I doubt there's anything this good available,
bang for the buck, that I have seen anywhere
nice talking w/ you Scott
Troy:cool:

I like the design - there's some nice features built-in, especially the upper shock mount (that's Ron on the phone now lol).

A couple quick questions.....I notice you changed the style of engine mount between the initial and current pics. Any reason?

Secondly - I note in the first picture (coated frame) a heavy-duty looking tab on top of the frame in front of the upper control arm mount - what are they for?

Thanks,
G

I should have new Frame by tommorow,I'll update my build page with pics of the frame and with the engine installed.....Thanks again Scott for the excellent customer service :thumbsup: :cheers:

I changed the motor mount design to allow more room for oil cooler lines next to the block.The thick tabs ahead of the UCA mounts are for the bolt on Bay mounts I made for the 72 camaro projects.I changed the upper shock mount alittle to take some fab time out of the frames.I want to keep improving my design all the time.I just want to put out the best product I can.Thank you to everybody who have bought and who have Looked.:thumbsup: :thumbsup:

Thanks for the info. I like your change to the engine mounts for the same reasons. Nice design.
G.

New Design Pricing is as follow's.Stage $4450.00,Stage II $4950.00,Stage III $6850.00,Dimple died hole's add $200.00(THIS PRICE IS SHIPPED)

Look's like I may have a Very Trusted Dealer on the westcoast who will start selling my sub frame's shortly.:thankyou: