complete track proven 1st gen camaro subframe
 

Hey guys, im working on a new chassis for my camaro and im going to sell my old setup. The chassis is powdercoated satin black and uses modified stock camaro lower arms and tubular upper arms. It will come complete ready to go with unisteer power rack, QA1 shocks, speedway engineering splined sway bar and wilwood brakes. All bushings and ball joints are new. The track width is two inches narrower than stock and is lighter than a stock sub. You can run an 18x11 wheel with no mods to the fender or inner fender. It will come with bay bars and a set of LS street and performance headers that i modified to fit the chassis. The trans crossmember is set up for a T56. I have had alot of success with this chassis and it should be a great setup for someone. All you will need to do is drop a motor and trans in it and bolt it in the car.

3500.00 shipped

kevin miller

Kevin, sub looks great. What spindles and hubs on the sub?

Let me know if you're going to part it out

It has stock spindles and hubs with new bearings. The control arms are narrowed an inch to help the camber gain. Right now i would like to sell it as a complete chassis.

thanks,
kevin miller

Kevin hi, any shots from the sub and eng clearance? Also can you run a stock ls pan? Thanks Gui

NEW PRICE $2500.00 shipped
 

sorry it took so long to respond. I dont really have any good pics of the motor in the chassis other than the ones i posted. The motor sits as low in the chassis as possible and oil pan is flush with the bottom of the crossmember. In my 69 camaro the cylinder heads are about 1/2" to 3/4" away from the firewall. I modified a stock F-body pan and notched it to make it clear. You can buy a modified F-body pan from street and performance or a champ pan will also work. I am going to get some good pictures up tomorrow of the chassis with no motor or trans in it.

thanks,
kevin miller

Can you send me the pics you take today? My email is grsdup1@aol. In your first pics with the engine installed, the the engine trans look very high in front, sloping down to the crossmember. It seems excessive, but you dont often get to look at things up high at eye level like in that pic. My concern is that its way more than 3* down. Thanks for your time.
Scott
850 380-9500

This seems like a great deal. I would not worry about the angle of the engine/trans until you start looking past 5*. As long as you have the ability to adjust your pinion angle to make your u-joint working angles correct it is not a problem! If you like this setup, I say go for it! :thumbsup:

Must have it figured out Scott as the car has proven it's self time and time again (that Dam car is REALLY fast and dollar for dollar stacks up against 1st gen out there)..... The price s right,,, the parts are proven indeed,,,, so it'll be a decision for someone to make on personal finances in my opinion....

Kevin tried PMing you clean out your file it is full.

The sub frame motor mount stands are in the same spot as a stock 67-69 camaro.Kevin used my chassis jig to build this sub frame.The motor and trans are in the same location as I install them in all of my sub frames and build's.

I was busy all day today and didnt get a chance to get any pics...I will try to get the pics tomorrow. I dont remember what the pinion angle was but my ridetech 4 link is fully adjustable with right and left hand heims so when we put the car together we adjusted out the pinion angle and never had any issues. The car always drove great and was always within a tenth or so of Brian Finch and Kyle Tucker.

Kevin Miller

Thanks for the kind words guys. sorry about the inbox...it should be all clear now.

kevin miller

Here are some photos.http://i1104.photobucket.com/albums/...miller2008.jpghttp://i1104.photobucket.com/albums/...miller2007.jpghttp://i1104.photobucket.com/albums/...miller2006.jpghttp://i1104.photobucket.com/albums/...miller2005.jpghttp://i1104.photobucket.com/albums/...miller2004.jpghttp://i1104.photobucket.com/albums/...miller2003.jpghttp://i1104.photobucket.com/albums/...miller2001.jpg

location
 

Hi there, Where are you located ? I am very interested in this subframe. Would be perfect for my camaro. Thanks, Mike

Im located in Baldwin City, Ks.

kevin miller

Kevin, nice setup. I like the home built stuff. I sent you a PM.

Thanks

So bummed on this.

Thanks Kevin. checked out the subframe today at Matts shop. Excellent craftsmanship! It was a pleasure doing business with both you and Scott. Now the search is on for a 4 link rear.

SOLD,SOLD,SOLD,:thumbsup: :thumbsup:

You bet rick, glad you guys are happy with the chassis. Im really happy with my ridetech 4 link. Scott is a dealer so if you decide you want to go ridetech he can get ya all set up. thanks again

kevin miller