Mega garage sale! - LS3 take out parts back on market
 

Well, time to clean out the garage again.. All prices are OBO.

If two people post then time stamps will determin who gets first dibs.


First up is a complete brake system from a 2001 Z28 Camaro. Includes rotors, pads, calipers, brackets, and hoses. The rotors are fairly new with only a couple of thousand miles on them. Make or buy some brackets and put them on your project. $120 plus shipping. SALE PENDING

http://i28.tinypic.com/u8o03.jpg


Next up is a bunch of take-out parts from an LS3. 58x crank, 8 rods and 8 pistons. The rings are cooked (went lean) but the rest seems fine. The only thing I would do is mic the pistons to ensure they are good to go. Crank and rods are perfect and the engine had about 7000 miles when these parts were pulled to build a stroker.

As a bonus there’s also a stock LS3 cam, springs and retainers.. add a block, a few parts and you have a dirt cheap short block. Heck, I will even toss in a few random parts I have laying around. $280 plus shipping for all. -- AVAILABLE

http://i32.tinypic.com/2ptp7vk.jpg

http://i25.tinypic.com/2crpueq.jpg


Finally found where I put my old McLeod SFI bellhousing. This is for an LS engine to a T56 transmission. No bolts but has the bell and the plate. Notched it to make bleading the clutch easier.

It’s this one… sell for $429 new but it’s $200 shipped here.
http://www.jegs.com/i/McLeod/673/8710-00/10002/-1

http://i25.tinypic.com/2qmhnoh.jpg


Holley 4150 Street HP 950 carb. New, left over from engine build.

Read all about it here: http://www.jegs.com/i/Holley/510/0-82951/10002/-1

Online price $540.. here it’s $300 shipped.. SOLD

http://i26.tinypic.com/30kyv7n.jpg


Comp 8957-16 LS lifters.. LS Series Captured Link Bar Retro-Fit Roller Lifter for 1997-
Up, Fits Both Factory and RHS®, LSX, Warhawk Blocks. As stated these are for aftermarket blocks or factory blocks if you don’t want to use the plastic lifter trays. New in box.

Street price is almost $500.. $200 shipped here. Did I mention they are new? SOLD

http://i30.tinypic.com/alhljb.jpg


ARP SBC 134-3601 head bolts.. new in box..

Specs here: http://www.summitracing.com/parts/ARP-134-3601/

$30 shipped -- SOLD

http://i27.tinypic.com/2vj3fy9.jpg


Powermaster 150 amp Alternator.. I bought the wrong one. Brand new in box.

Part number 58272, look up the part number and see what it fits or make it fit your project.

http://www.jegs.com/i/Powermaster/713/58272/10002/-1

$230 new.. $100 shipped OBO

http://i26.tinypic.com/ixyzbt.jpg


Two Fragola AN fittings - Fitting, Straight, Male -10 AN to Straight Cut Male -12 AN O-Ring,

http://www.summitracing.com/parts/FRA-495107/

$18 shipped for both.. so it’s a bit better than buy one get one free.. new, never used.

http://i31.tinypic.com/1y09jc.jpg

Steve are those Brake caliper Aluminum? IF so can you PM me shipping to 03109 the bell too :-)

I want the head bolts, how do you want paid ?
Tommy Lee

I'll take the brakes if xlexustech doesn't.

Camaro calipers are aluminum like the Corvette ones.. just a bit less stiff.

Call shipping $25 so $145 total (they are pretty heavy)

Let me know asap as someone on PT.com asked the same question.

The bell is $200 shipped.. I will hold that until you confirm you want.

UPDATE The other buyer accepted the shipping so the brakes are sold. He also wanted the bellhousing but you asked first so you get right-of-first-refuse :) Let me know

I'm always amazed how fast some of this stuff goes.. I need to raise my prices!!! lol (just kiddin')

Third in line :)

You're first in line (by four minutes).. paypal works great and I will cover the fee.

[email protected]

Work for you?

no questions here, just paypal.

Brakes are sold.. first reponder ok'd the shipping.

If I come across more I will let you know. These came off Nick's project Black Betty (just swapped to Wilwoods)

I posted on Pro-touring.com already but just covering my butt! I will take the LS parts (crank, rods, etc.) and also the lifters. I am local too so no shipping.