View Single Post
  #1  
Old 07-11-2010, 12:13 PM
Steve1968LS2's Avatar
Steve1968LS2 Steve1968LS2 is offline
Moderator
 
Join Date: Feb 2005
Location: Anaheim Hills, CA
Posts: 5,534
Thanks: 0
Thanked 4 Times in 2 Posts
Default Mega garage sale! - LS3 take out parts back on market

Well, time to clean out the garage again.. All prices are OBO.

If two people post then time stamps will determin who gets first dibs.


First up is a complete brake system from a 2001 Z28 Camaro. Includes rotors, pads, calipers, brackets, and hoses. The rotors are fairly new with only a couple of thousand miles on them. Make or buy some brackets and put them on your project. $120 plus shipping. SALE PENDING




Next up is a bunch of take-out parts from an LS3. 58x crank, 8 rods and 8 pistons. The rings are cooked (went lean) but the rest seems fine. The only thing I would do is mic the pistons to ensure they are good to go. Crank and rods are perfect and the engine had about 7000 miles when these parts were pulled to build a stroker.

As a bonus there’s also a stock LS3 cam, springs and retainers.. add a block, a few parts and you have a dirt cheap short block. Heck, I will even toss in a few random parts I have laying around. $280 plus shipping for all. -- AVAILABLE






Finally found where I put my old McLeod SFI bellhousing. This is for an LS engine to a T56 transmission. No bolts but has the bell and the plate. Notched it to make bleading the clutch easier.

It’s this one… sell for $429 new but it’s $200 shipped here.
http://www.jegs.com/i/McLeod/673/8710-00/10002/-1




Holley 4150 Street HP 950 carb. New, left over from engine build.

Read all about it here: http://www.jegs.com/i/Holley/510/0-82951/10002/-1

Online price $540.. here it’s $300 shipped.. SOLD




Comp 8957-16 LS lifters.. LS Series Captured Link Bar Retro-Fit Roller Lifter for 1997-
Up, Fits Both Factory and RHS®, LSX, Warhawk Blocks. As stated these are for aftermarket blocks or factory blocks if you don’t want to use the plastic lifter trays. New in box.

Street price is almost $500.. $200 shipped here. Did I mention they are new? SOLD




ARP SBC 134-3601 head bolts.. new in box..

Specs here: http://www.summitracing.com/parts/ARP-134-3601/

$30 shipped -- SOLD




Powermaster 150 amp Alternator.. I bought the wrong one. Brand new in box.

Part number 58272, look up the part number and see what it fits or make it fit your project.

http://www.jegs.com/i/Powermaster/713/58272/10002/-1

$230 new.. $100 shipped OBO




Two Fragola AN fittings - Fitting, Straight, Male -10 AN to Straight Cut Male -12 AN O-Ring,

http://www.summitracing.com/parts/FRA-495107/

$18 shipped for both.. so it’s a bit better than buy one get one free.. new, never used.

__________________
"A ship in port is safe, but that's not what ships are built for."

See Bad Penny run the cones: https://www.youtube.com/watch?v=8GUPPIX-92U

1971 Chevelle Wagon - Roadster Shop Chassis ProCharged Shafiroff LS and lots of yada yada

1968 Camaro - Project Track Rat - 440 RHS LS

Last edited by Steve1968LS2; 07-12-2010 at 05:19 PM.
Reply With Quote