...

Go Back   Lateral-g Forums > Technical Discussions > Interior and Electrical
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 07-15-2019, 10:29 AM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default AAW + RS Headlights + LED 7" Round

I know everyone loves wiring......

I have a 1967 RS with all American Auto Wire classic update kit. It includes the RS harness which mimics the original 3 relay door system.

The doors open but will not close. When i put a resistor inline I can get one door to close but not both. I think the issue is the filament path to ground with the LED is different than an H4 style.

From their instructions:
The Control Circuit is energized when the headlamp switch is "OFF" and the ignition switch is "ON". Relay R1 is
not energized. Relays R2 and R3 are energized through the ignition switch through the one-way diode, the relay
coils, the headlamp switch terminal, the dimmer switch, and finally through the sealed beam filaments to ground.

Has anyone else encountered an issue with getting the door to close. AAW recommended trying to tap into the lead wire to the high/beam switch on the floor with a resistor. I haven't tried that yet.

Thanks
Reply With Quote
  #2  
Old 07-15-2019, 12:03 PM
blitzer454 blitzer454 is offline
Member
 
Join Date: Nov 2011
Posts: 38
Thanks: 1
Thanked 16 Times in 12 Posts
Default

You could use a resistor placed on the light blue wire of relay R1 to ground but it would need to be a pretty big power resistor. The resistance would need to be around 6 ohms and the wattage would need to be 38W or more. A better solution is to use a relay. Here's a circuit showing how to connect relay R4.

You don't need to use the same type of relay as used in the original headlight door circuit. Any standard 12V automotive relay will work.
Reply With Quote
  #3  
Old 07-15-2019, 12:53 PM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Thanks for the insight. I have a relay on hand and will start with that approach.
Reply With Quote
  #4  
Old 07-15-2019, 01:21 PM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Reading the diagram

86 - ground
87a - ground
87 + 30 - light blue from coming from the dash
85 - back to original relay one terminal
Reply With Quote
  #5  
Old 07-15-2019, 02:34 PM
blitzer454 blitzer454 is offline
Member
 
Join Date: Nov 2011
Posts: 38
Thanks: 1
Thanked 16 Times in 12 Posts
Default

I updated the circuit with the terminal numbers, so trying clicking it again.

Just in case that doesn't work:
85 and 87a: Ground
86 and 87: L Blue wire from connector
30: L Blue wire to R1
Reply With Quote
The Following User Says Thank You to blitzer454 For This Useful Post:
nicks67ca (07-15-2019)
  #6  
Old 07-15-2019, 03:23 PM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Got it Thanks!
Reply With Quote
  #7  
Old 08-07-2022, 11:49 PM
67_camaroRS's Avatar
67_camaroRS 67_camaroRS is offline
Member
 
Join Date: Jul 2015
Location: Los Angeles, CA
Posts: 95
Thanks: 5
Thanked 6 Times in 4 Posts
Default

did this end up working for you?
__________________
1967 Camaro RS
1969 Camaro coupe
Reply With Quote
  #8  
Old 08-10-2022, 09:07 AM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

They open and close but I think i still have an issue somewhere and can't determine if i wired wrong or something else.

They open with the switch and key on.
When I turn them off the lights go off but the doors stay open
When I turn the key off then back on one closes one stays open
If i tap the open on it will close - it acts like a dead spot or stuck

After putting it together i just haven't had the time / motivation to figure this out.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:45 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net