...

Go Back   Lateral-g Forums > Technical Discussions > Brakes
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 09-18-2009, 12:13 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default Official: Brake Pad Knock Back Thread

As some of you know I and a few others have fought brake pad knock back issues. With a fixed caliper like many of the large manufacturers use, any slack in the bearings under load cause the pads to recede the pistons into the caliper. This isn't so great the next time you hit the brake pedal since you experience more pedal travel than the previous stroke.

The first time I autocrossed my car I had to pump the brakes between the corners. I determined I had .020.021 play end play in each axle. I bought some different retainer plates and got it down to .005/.006. While that has improved it tremendously, I'm still not satisfied on the street or track. I know it's not the front because I have C6 bearing packs and they only net .001 play. At this point I called Wilwood and they don't offer a floating caliper so I would need to switch brakes if I go that route. My number two thought is to go to a tapered bearing. I called moser and they said most circle track and autocrossers run a tapered bearing but he couldn't guarantee that would fix my problem. He also said .005 was tight enough for a roller bearing.

I can't really get anybody to cough up a spec on how tight the axle end play should be. Wilwood is actually sending me some shims but how much tighter can I go and will .002-.003 really help that much. Has anyone changed from a roller to a tapered bearing and has it helped? I'm experiencing a change in brake pedal even on the street under normal drving conditions. While it's managable on the street and track. I want a consistant brake pedal. I had a brief conversation with Frank at Prodigy yesterday and it's happening with other brake manufacturers as well. He said he knows a guy that is running a 10psi residual valve in the front and back. While I'm sure that would fix my issue, I feel it will cause excess heat and pad wear on a cruise that could potentially cause brake failure.
__________________
Todd
Reply With Quote
  #2  
Old 09-18-2009, 12:39 PM
XcYZ's Avatar
XcYZ XcYZ is offline
Administrator
 
Join Date: Jun 2004
Location: Rochester, Minnesota
Posts: 8,963
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Do you think 10 psi residual valves would put that much heat into the rotors? I don't know, but I kind of doubt it. I do think it would make for a lot more brake dust, though.

It would be an interesting test to put your car on jackstands, run it in gear for X amount of time then check the rotor face temp with an infrared thermometer, then install the residual valves and repeat the test (noting the ambient temps).

The amount of energy absorbed and dissapated through the rotors from regular daily driving just makes the 10 psi residual valves seem underwhelming. Again, I don't know, just sayin.
__________________
Scott

My LS7 69 Camaro
Reply With Quote
  #3  
Old 09-18-2009, 02:35 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

Sounds like a 12 pack experiement. I'd want to run the car at highway speeds for a reasonable distance. I just feel like that's a bandaid covering up the actual problem. I put a 2lb in the rears but it's not enough to move the pistons back. I'll check with Frank and see if the individual he knows is running a tapered bearing.
__________________
Todd
Reply With Quote
  #4  
Old 09-18-2009, 03:17 PM
XcYZ's Avatar
XcYZ XcYZ is offline
Administrator
 
Join Date: Jun 2004
Location: Rochester, Minnesota
Posts: 8,963
Thanks: 0
Thanked 0 Times in 0 Posts
Default

lol...

I'm running tapered bearings in my 9"... I'd hate to say that there's no runout, but I can't feel any when I've messed with it.
__________________
Scott

My LS7 69 Camaro
Reply With Quote
  #5  
Old 09-18-2009, 03:36 PM
Vegas69's Avatar
Vegas69 Vegas69 is offline
Senior Member
 
Join Date: Dec 2006
Posts: 8,663
Thanks: 86
Thanked 210 Times in 119 Posts
Default

Are you running a fixed caliper out back Scott?
__________________
Todd
Reply With Quote
  #6  
Old 09-18-2009, 03:41 PM
XcYZ's Avatar
XcYZ XcYZ is offline
Administrator
 
Join Date: Jun 2004
Location: Rochester, Minnesota
Posts: 8,963
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Yep, they're fixed.
__________________
Scott

My LS7 69 Camaro
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:17 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net