|
|
10-20-2021, 06:12 PM
|
 |
Lateral-g Supporting Vendor
|
|
Join Date: Jul 2005
Posts: 854
Thanks: 211
Thanked 448 Times in 203 Posts
|
|
Why dual exhaust, other than to have two tailpipes?
Andrew
__________________
Instagram @projectgattago
I offer remote Holley EFI tuning.
I deliver what EFI promises.
Please get in touch if I can be of service.
My YouTube Channel
|
10-20-2021, 08:01 PM
|
 |
Administrator
|
|
Join Date: Jul 2004
Location: Wilton, CA.
Posts: 12,586
Thanks: 4,325
Thanked 1,457 Times in 630 Posts
|
|
Quote:
Originally Posted by andrewb70
Why dual exhaust, other than to have two tailpipes?
Andrew
|
To have two tailpipes... 
|
|
The Following 7 Users Say Thank You to camcojb For This Useful Post:
|
|
10-30-2021, 03:48 PM
|
|
Administrator
|
|
Join Date: Jul 2004
Location: Wilton, CA.
Posts: 12,586
Thanks: 4,325
Thanked 1,457 Times in 630 Posts
|
|
Tweaked some of the piping and got it so none of the exhaust is below the trans level, should be good enough. Gas tank should ship next week so I can finish the tailpipes and fuel lines, then the body comes off for hopefully bodywork, and the chassis can be powdercoated and final assembly done.
|
|
The Following 6 Users Say Thank You to camcojb For This Useful Post:
|
|
10-31-2021, 04:34 PM
|
|
Administrator
|
|
Join Date: Jul 2004
Location: Wilton, CA.
Posts: 12,586
Thanks: 4,325
Thanked 1,457 Times in 630 Posts
|
|
TMI Sport seats showed up today. Feel great sitting on the ground...
|
|
The Following 6 Users Say Thank You to camcojb For This Useful Post:
|
|
10-31-2021, 08:17 PM
|
 |
Senior Member
|
|
Join Date: Dec 2011
Location: Colorado, in a van down by the river
Posts: 1,244
Thanks: 806
Thanked 259 Times in 157 Posts
|
|
WOW those are going to be comfy!
|
|
The Following User Says Thank You to jarhead For This Useful Post:
|
|
11-01-2021, 10:12 AM
|
 |
Lateral-g Supporting Member
|
|
Join Date: Oct 2006
Location: Ma
Posts: 8,424
Thanks: 908
Thanked 336 Times in 229 Posts
|
|
I was thinking of a set for my car, but I’m not 6’ tall but I am a wide body. So fitting in performance seats is challenge. Those are gonna look so sweet in your car.
|
|
The Following User Says Thank You to waynieZ For This Useful Post:
|
|
11-02-2021, 03:40 PM
|
|
Administrator
|
|
Join Date: Jul 2004
Location: Wilton, CA.
Posts: 12,586
Thanks: 4,325
Thanked 1,457 Times in 630 Posts
|
|
So I bolted the sliders and brackets on the drivers seat, and installed it in the car. I'm 6'5" tall and I still have 3" of head clearance, and I don't have to tilt the seats back to gain the headroom. Normally I have to mod the seat brackets to get them low enough for me, but the TMI units are lower right out of the box.
Seats are super comfortable, and feel like they'll hold me in place very well. Super happy with the TMI stuff. 
|
|
The Following 7 Users Say Thank You to camcojb For This Useful Post:
|
|
11-02-2021, 03:53 PM
|
|
Lateral-g Supporting Member
|
|
Join Date: Oct 2006
Location: Ma
Posts: 8,424
Thanks: 908
Thanked 336 Times in 229 Posts
|
|
Sweet! They look nice.
|
|
The Following User Says Thank You to waynieZ For This Useful Post:
|
|
11-02-2021, 04:15 PM
|
 |
Senior Member
|
|
Join Date: Nov 2004
Location: washington, ok
Posts: 4,273
Thanks: 22
Thanked 159 Times in 93 Posts
|
|
Quote:
Originally Posted by camcojb
So I bolted the sliders and brackets on the drivers seat, and installed it in the car. I'm 6'5" tall and I still have 3" of head clearance, and I don't have to tilt the seats back to gain the headroom. Normally I have to mod the seat brackets to get them low enough for me, but the TMI units are lower right out of the box.
Seats are super comfortable, and feel like they'll hold me in place very well. Super happy with the TMI stuff. |
TMI seats looks nice and fit nice, I wish they were a tad softer. All the ones I have installed have been on the extra firm side for me.
__________________
Mike Redpath
Musclerodz & Customz
facebook page
Last edited by Musclerodz; 11-02-2021 at 04:18 PM.
|
|
The Following User Says Thank You to Musclerodz For This Useful Post:
|
|
11-02-2021, 04:53 PM
|
|
Administrator
|
|
Join Date: Jul 2004
Location: Wilton, CA.
Posts: 12,586
Thanks: 4,325
Thanked 1,457 Times in 630 Posts
|
|
Quote:
Originally Posted by Musclerodz
TMI seats looks nice and fit nice, I wish they were a tad softer. All the ones I have installed have been on the extra firm side for me.
|
You need to gain some weight... They are firm, but not too much so IMO. Actually feels good on my lower back.
|
|
Tags
|
70 chevelle, aeromotive, american powertrain, amsoil, baer brakes, borgeson, clayton machine, currie, dakota digital, eddie motorsports, forgeline, holley performance, hydratech, ididit, lateral-g, lokar, magnaflow, mcleod racing, mighty mouse solutions, modo innovations, morris classic concepts, painless performance, protouring, restomodair, roadster shop, rock valley antique auto parts, ron davis, texas speed, thermotec, tmi products, vintage air  |
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 11:43 AM.
|
Brian Hobaugh SCCA National Tour June 2014
First Hemi 'Cuda Convertible Ever Built
Short clips: Goodguys Pleasanton autocross and pit videos
Linear Mode
