...

Go Back   Lateral-g Forums > Technical Discussions > Paint and Body
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 03-03-2021, 09:34 AM
jarhead's Avatar
jarhead jarhead is offline
Senior Member
 
Join Date: Dec 2011
Location: Colorado, in a van down by the river
Posts: 1,243
Thanks: 801
Thanked 258 Times in 156 Posts
Default finish and paint bottom before bodywork?

My car is on a rotisserie and I am currently finishing the floorpan metalwork, mini tubs, and a Speedtech torque arm install.

I am curious if the process is to completely finish the metalwork on the bottom and then paint and spray Bedliner?

The rest of the car would still need quarter panel patches, trunk weatherstrip area patched, etc.

Thanks!
__________________
joe
Semper Fi

My 68 Torino
Reply With Quote
  #2  
Old 03-03-2021, 10:27 AM
raustinss raustinss is offline
Senior Member
 
Join Date: Dec 2013
Location: Kitchener ,Ontario
Posts: 802
Thanks: 50
Thanked 77 Times in 61 Posts
Default

not that im an expert in anything but i dont see a problem with it ,as long as all the rest of the panels are good ...rockers inner rockers trunk drop offs wheel wells etc
Reply With Quote
The Following User Says Thank You to raustinss For This Useful Post:
jarhead (03-04-2021)
  #3  
Old 03-03-2021, 11:25 AM
Ketzer's Avatar
Ketzer Ketzer is offline
Lateral-g Supporting Member
 
Join Date: Feb 2008
Location: Eads, TN.
Posts: 1,403
Thanks: 299
Thanked 140 Times in 97 Posts
Default

This is how I did my current project, epoxy prime and Raptor on the bottom before starting bodywork on the top...give me another two years and Ill know if it was a mistake



Jeff-
__________________
You remind me of the timing on a turbo engine...
Reply With Quote
The Following 2 Users Say Thank You to Ketzer For This Useful Post:
jarhead (03-04-2021), Spiffav8 (03-08-2021)
  #4  
Old 03-03-2021, 12:34 PM
dhutton dhutton is online now
Senior Member
 
Join Date: Nov 2006
Location: Mountain Springs, Texas
Posts: 1,857
Thanks: 985
Thanked 448 Times in 247 Posts
Default

I have a somewhat different process. All metal work done, then rotisserie, then media blast all non exterior flat panels which I strip by sanding, then 3 coats epoxy primer whole shell, then bedliner, then filler work within epoxy recoat window, then epoxy, then poly primer, then block entire car, then urethane primer, then block whole car 180 through 400 then ready for epoxy sealer and paint.

Your method will work, it’s just that some metal work is best done with the car properly supported and not on a rotisserie. It is also a bit tougher to keep the bedliner looking good.

Don
Reply With Quote
The Following User Says Thank You to dhutton For This Useful Post:
jarhead (03-04-2021)
  #5  
Old 03-03-2021, 12:54 PM
patriot68 patriot68 is offline
Senior Member
 
Join Date: May 2005
Location: San Antonio,TX
Posts: 146
Thanks: 1
Thanked 24 Times in 13 Posts
Default

did my underneath first
__________________
1968 Camaro, LS1/T56,martz chassis,19x10/18x8 Budniks,245/45/18,295/35/19 {Sold}
http://www.fquick.com/patriot68

1971 Firebird - Speedtech Extreme Subframe/Torque Arm, LS3/4L80E, 19x12/18x10 Budniks
Reply With Quote
The Following User Says Thank You to patriot68 For This Useful Post:
jarhead (03-04-2021)
  #6  
Old 03-03-2021, 07:31 PM
jarhead's Avatar
jarhead jarhead is offline
Senior Member
 
Join Date: Dec 2011
Location: Colorado, in a van down by the river
Posts: 1,243
Thanks: 801
Thanked 258 Times in 156 Posts
Default

Thanks all.

Don, thanks, I've been wondering about removing from rotisserie to complete. You may have seen my car on IG (jarhead1017). Working on the Speedtech install now, had to remove part of the trunk.
__________________
joe
Semper Fi

My 68 Torino
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:24 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net