...

Go Back   Lateral-g Forums > Lateral-G Open Discussions > Project Updates
User Name
Password



Reply
 
Thread Tools Display Modes
  #101  
Old 01-05-2020, 10:23 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default

Because the DSE kit is based around a 4th gen Camaro master. I just copy the 4th Gen Camaro clutch pedal geometry. I purchased a stock 1992 Camaro Clutch pedal along time before all these stuff was available so I just use it as a template.

Here is the 69 vs 1991 pedal.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 2 Users Say Thank You to Stielow For This Useful Post:
rat_rod_russell (04-21-2020), WILWAXU (01-05-2020)
  #102  
Old 01-05-2020, 10:26 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default Camaro LT5

I weld on a tab to pick up the end of the clutch master cylinder. I drilled a hole in the stock pivot point on the 1991 pedal. I use a transfer punch to locate the new location on the 69 pedal.

I then drill and tab the new tab 1/4 - 20.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering

Last edited by Stielow; 01-05-2020 at 10:29 AM.
Reply With Quote
The Following 2 Users Say Thank You to Stielow For This Useful Post:
rat_rod_russell (04-21-2020), WILWAXU (01-05-2020)
  #103  
Old 01-05-2020, 10:31 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default

I used to use the stock 4 th gen GM master cylinders then they got fairly expensive and they were plastic. I found this part on Summit Racing web site and it is aluminum.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 2 Users Say Thank You to Stielow For This Useful Post:
rat_rod_russell (04-21-2020), WILWAXU (01-05-2020)
  #104  
Old 01-05-2020, 10:37 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default Camaro LT5

If you carefully remove the stock end that designed to hook to the stock 4th Gen Camaro pedal the Dorman part has 1/4 - 20 treads. I run a die down those threads after I remove the crimes on part.

I then use a piece of 5/16 thick wall tubing to make a new rod. Drill and tap one end 1/4 - 20 and the other end 1/4 - 28 for a 1/4 rod end






Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 4 Users Say Thank You to Stielow For This Useful Post:
Goosesdad (01-05-2020), kwhizz (01-06-2020), rat_rod_russell (04-21-2020), WILWAXU (01-05-2020)
  #105  
Old 01-05-2020, 10:47 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default

Sorry got ahead of myself a bit. Need to set the length of the rod prior to cutting it.

I mock it up on my table to sort that out.

Copying the stock 4th gen geometry should make the linkage at a 90 degree angle at 1/2 stroke. It you draw a line from the pivot point of the pedal to the pivot point of the rod end the to the center of the master cylinder it should be 90 degrees. This keeps the side load on the master cylinder to a minimum. If you are failing master cylinders most likely your geometry it incorrect and your side loading the master cylinder.

While you have the assembly out of the car and on the work bench also verify the push rod is straight. The centerline of the master cylinder and the push rod should be straight at half stroke. In my setup I had to add two washers to straighten it up.

I later tack welded the washers on the pedal to make it easier to assemble later.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 5 Users Say Thank You to Stielow For This Useful Post:
Goosesdad (01-05-2020), jarhead (01-20-2020), rat_rod_russell (04-21-2020), Sonar Chief (01-06-2020), WILWAXU (01-05-2020)
  #106  
Old 01-05-2020, 10:49 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default Camaro LT5

I had to clearance the support to clear my bolts.

I use a long stud to make assembling all this in the car easier.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 3 Users Say Thank You to Stielow For This Useful Post:
Goosesdad (01-05-2020), rat_rod_russell (04-21-2020), WILWAXU (01-05-2020)
  #107  
Old 01-05-2020, 10:55 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default

Because the LT5 ECM is looking for a clutch switch and I’m adding Cruise control I added a clutch switch also while I was making stuff.



My disclaimer. This works for me and there maybe other ways to do it. I have used this system on the last 5 Camaros with zero issues. I then to revert back to “what do GM do” for a lot of my solutions.

It is amazing the the 1969 clutch pedal and the 1991 pedal are the same length. These setup coupled with a Centerforce clutch make the clutch pedal feel like a stock Camaro.


Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 6 Users Say Thank You to Stielow For This Useful Post:
fleetus macmullitz (01-05-2020), Goosesdad (01-05-2020), rat_rod_russell (04-21-2020), Roscoe03 (01-06-2020), Sonar Chief (01-06-2020), WILWAXU (01-05-2020)
  #108  
Old 01-05-2020, 11:00 AM
Stielow's Avatar
Stielow Stielow is offline
Lateral-g Supporting Member
 
Join Date: Dec 2004
Posts: 2,502
Thanks: 29
Thanked 2,184 Times in 593 Posts
Default

Sorry one more thing. I add an adaptor to the Dorman Master Cylinder to convert to -4 AN line. Make hooking up the clutch easier. You can just purchase a premade line to fit. I do add a dry break so if I do need to pull the transmission I don’t have to re bleed the system.




Sent from my iPhone using Tapatalk
__________________
Stielow Engineering
Reply With Quote
The Following 6 Users Say Thank You to Stielow For This Useful Post:
CarlC (01-06-2020), craig510 (01-05-2020), dhutton (01-05-2020), Goosesdad (01-05-2020), jarhead (01-20-2020), WILWAXU (01-05-2020)
  #109  
Old 01-05-2020, 06:25 PM
WSSix WSSix is offline
Lateral-g Supporting Member
 
Join Date: Nov 2008
Location: Dunwoody, GA
Posts: 6,459
Thanks: 942
Thanked 690 Times in 541 Posts
Default

Excellent information, Mark. Thanks for being so detailed
__________________
Trey

Current rides: 2000 BMW 540i/6 and 86 C10.

Former ride: 1979 Trans Am WS6: LT1/T56, Kore 3 C5/6 brakes, BMW 18in rims
Reply With Quote
  #110  
Old 01-06-2020, 06:21 AM
kwhizz's Avatar
kwhizz kwhizz is offline
Lateral-g Supporting Member
 
Join Date: Nov 2005
Location: Kenosha , wi
Posts: 1,136
Thanks: 673
Thanked 432 Times in 163 Posts
Default

When I took the Impala Convert I bought apart...…. Here's what I found for brake pedal linkage...….. LOL...… Pretty scary....

Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:12 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net