...

Go Back   Lateral-g Forums > Technical Discussions > Interior and Electrical
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 07-18-2020, 08:34 AM
69hugger's Avatar
69hugger 69hugger is offline
Senior Member
 
Join Date: Feb 2014
Location: Minneapolis, MN
Posts: 449
Thanks: 136
Thanked 83 Times in 42 Posts
Default LED's popping fuse?

I recently bought a '67 C-10 pickup with all LED lighting. The wiring is AAW, and the truck was professionally built. The license plate lights utilized those bolts with LEDs to illuminate the plate. Those LED bolts had been wrecked by the consignment dealer when they removed the old license plate. They twisted the wires, breaking & shorting them, causing blown fuses on the running light circuit. Their fix was to just cut the wiring to the bolts, and cap the brown supply wire. No more popped fuses.
Wanting to have license plate lights, I bought some new LED bolts (from Amazon), and figured I'd just replace the trashed ones. I tested them from the package, and they worked great. I then wired bullet connectors to them and the brown supply wire, soldering the wires to the bullets. Then covered all the connectors with shrink tubing.
When I plugged the lights into the wiring and pulled the parking light switch, instant popped fuse. I unplugged the lights, replaced the fuse, and tested the brown supply wire to ground, my test light worked fine, no popped fuse. I tested the LED lights again across a battery, and they worked fine.
My only theory is that the LEDs draw so little current is the circuit sees them as a dead short, popping the fuse.
I wonder if I need to wire in a resistor so there is more of a load on that circuit. If so, I have no idea that specs the resistor would need to be. Or the best place to get them.
Any electrical wizards that can either confirm my thought or give me another idea as to why these are causing blown fuses would be greatly appreciated.

As always, thanks in advance!!

Bill
__________________
Bill


'69 Camaro / 534 BBC / DSE Built
'67 C10 / LS-3 Magnuson / Roadster Shop Chassis
Reply With Quote
  #2  
Old 07-18-2020, 07:29 PM
214Chevy's Avatar
214Chevy 214Chevy is offline
Lateral-g Supporting Member
 
Join Date: Jul 2008
Location: DALLAS, Texas
Posts: 4,541
Thanks: 283
Thanked 536 Times in 338 Posts
Default

Sorry, I don't know anything about your wiring issue. But, I do want to see pics of that C10 though.
__________________
'68 C10 swb
'69 Camaro convertible
'72 Chevelle

Reply With Quote
  #3  
Old 07-18-2020, 07:47 PM
dhutton dhutton is offline
Senior Member
 
Join Date: Nov 2006
Location: Mountain Springs, Texas
Posts: 1,857
Thanks: 985
Thanked 448 Times in 247 Posts
Default

No way something drawing too little current will blow a fuse. For some reason your LED is presenting a short.

Post some pics of how you have it wired. A pic of the LED you used would be useful too. A link to the LED too.

I’m guessing the plus side of the LED is connected to the bolt itself. No idea why.

Don

Last edited by dhutton; 07-18-2020 at 07:56 PM.
Reply With Quote
  #4  
Old 07-19-2020, 08:54 AM
69hugger's Avatar
69hugger 69hugger is offline
Senior Member
 
Join Date: Feb 2014
Location: Minneapolis, MN
Posts: 449
Thanks: 136
Thanked 83 Times in 42 Posts
Default

I’ll have to re-address how to post pics. Haven’t done so for a few years, since the bucket debacle.
__________________
Bill


'69 Camaro / 534 BBC / DSE Built
'67 C10 / LS-3 Magnuson / Roadster Shop Chassis
Reply With Quote
  #5  
Old 07-30-2020, 04:38 PM
69hugger's Avatar
69hugger 69hugger is offline
Senior Member
 
Join Date: Feb 2014
Location: Minneapolis, MN
Posts: 449
Thanks: 136
Thanked 83 Times in 42 Posts
Default

The culprit turned out to be not the license plate led bolts, but a short in a front turn signal. I found it by dumb luck.
New housing and all is golden.
Case closed.

Thanks for the interest!
__________________
Bill


'69 Camaro / 534 BBC / DSE Built
'67 C10 / LS-3 Magnuson / Roadster Shop Chassis
Reply With Quote
The Following 3 Users Say Thank You to 69hugger For This Useful Post:
camcojb (07-30-2020), Spiffav8 (08-08-2020), WILWAXU (08-07-2020)
  #6  
Old 08-06-2020, 04:53 PM
moneypit68's Avatar
moneypit68 moneypit68 is offline
Member
 
Join Date: Feb 2017
Location: Orlando, FL
Posts: 27
Thanks: 3
Thanked 1 Time in 1 Post
Default

I was definitely going to say it was a short in the wiring. How’d the turn signal short out? I’d take a look and see what else is rubbing and could eventually short. Wish I did the same before I lit my Cadillac on fire as a teenager with terrible speaker wiring haha.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:21 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright Lateral-g.net