Nice work!

I really like the drip rail shave :D

Joe

Brian fit and welded the Global West subframe connectors.

http://img.photobucket.com/albums/v3...ps0jrxfmiz.jpg

http://img.photobucket.com/albums/v3...psfhmbnnqk.jpg

Brian did not like how the torque boxes fit in the rear so he fixed that.

http://img.photobucket.com/albums/v3...psijo4ggmw.jpg

http://img.photobucket.com/albums/v3...ps7gefvsxy.jpg

That looks much better.

Epoxy primed the engine compartment and undercarriage

http://img.photobucket.com/albums/v3...psi8ydmw37.jpg

http://img.photobucket.com/albums/v3...psc3g81hps.jpg

Started the bodywork on the fender aprons

http://img.photobucket.com/albums/v3...pshbgtqdmb.jpg

http://img.photobucket.com/albums/v3...psyqxoaout.jpg

The extra holes in the firewall were patched and the engine compartment epoxy primed

http://img.photobucket.com/albums/v3...pse3mucbw3.jpg

I still wasn't happy with the fender aprons and we did a little bodywork on the firewall

http://img.photobucket.com/albums/v3...psx6mnpcqm.jpg

http://img.photobucket.com/albums/v3...psyccy6sj4.jpg

http://img.photobucket.com/albums/v3...psyirhrq8o.jpg

One coat of SPI epoxy primer

http://img.photobucket.com/albums/v3...psek0hfe0z.jpg

http://img.photobucket.com/albums/v3...psykplqchl.jpg

Two coats of SPI Turbo urethane primer

http://img.photobucket.com/albums/v3...psitwmuiwv.jpg

http://img.photobucket.com/albums/v3...pstaxoesfo.jpg

I admire your attention to detail ... reminds me of someone I know :rolleyes:

Been following your build ethics and steps for a perfect paint job, keep up the great work!

Michael

Looks great and gave me some ideas for mine :-)

I never have liked the way Ford just stuck the taillights on the outside of the taillight panel and the owner agreed. He wanted to install 67 taillights but the taillight panel is to small so we are recessing the taillights. He ordered a set of billet bezels from Eddie Motorsports.

The first step was to get the taillights to fit the new taillight panel and trace around it.

http://img.photobucket.com/albums/v3...psweazmssz.jpg

Brian decided to make a new inner bracket out of thicker metal.

http://img.photobucket.com/albums/v3...pslur1mubr.jpg

This was his first attempt but it was a little to small so he had to make another one out of an old seat riser.

http://img.photobucket.com/albums/v3...psb3bspmp4.jpg

Test fitting the taillight

http://img.photobucket.com/albums/v3...psu98ruxje.jpg

His new bracket tack welded in place

http://img.photobucket.com/albums/v3...pszqdlwkgc.jpg

http://img.photobucket.com/albums/v3...psh0nu2wdc.jpg

The top piece is just to hold it in place and will be trimmed.

http://img.photobucket.com/albums/v3...psgunilhgx.jpg

http://img.photobucket.com/albums/v3...ps1zpiznun.jpg

The next step will be to make the filler pieces

Nice idea its going to look great.

Brian cut out the other side and test fit the taillights

http://img.photobucket.com/albums/v3...pse0ktirbu.jpg

http://img.photobucket.com/albums/v3...psriqbse0i.jpg

http://img.photobucket.com/albums/v3...ps96y64hou.jpg

http://img.photobucket.com/albums/v3...psfpav6o9f.jpg

Nice job!! I like that as well, I think the Eddie's bezel's are too chunky looking. Maybe a better work os bulky looking? But with them recessed it takes care of that issue.

Looks great!