So many little touches on this car that will make it look great. I'm glad you're showing them since I don't know Mustangs well enough to pick them out on my own.

Fixing the trunk gap

http://img.photobucket.com/albums/v3...psibt1ljnm.jpg

http://img.photobucket.com/albums/v3...psp8cosasf.jpg

The owner wanted a spoiler but did not like how tall it was so we lowered the Mustangs to Fear spoiler and end caps about 1". It will be straight with the top of the quarter

http://img.photobucket.com/albums/v3...psxkkmutaz.jpg

http://img.photobucket.com/albums/v3...pshpbcu0j9.jpg

Spoiler cut and test fitting

http://img.photobucket.com/albums/v3...psaldvz7cu.jpg

Looking good , Rusty.

The end caps were bolted, bonded and fiberglass mat added to the quarter panel

http://img.photobucket.com/albums/v3...psp60nlakj.jpg

The spoiler was bonded to the deck lid and fiberglass mat added

http://img.photobucket.com/albums/v3...psg9vkklcd.jpg

http://img.photobucket.com/albums/v3...psztzqaofh.jpg

http://img.photobucket.com/albums/v3...psqomr1qgm.jpg

I epoxy primed the body

http://img.photobucket.com/albums/v3...pssw0wl89n.jpg

Block sanded and a little more bodywork

http://img.photobucket.com/albums/v3...ps0dgiwphu.jpg

http://img.photobucket.com/albums/v3...psc3jhanqc.jpg

One coat of SPI epoxy primer

http://img.photobucket.com/albums/v3...psx809ct9x.jpg

Two coats of SPI Turbo primer

http://img.photobucket.com/albums/v3...psjcpaemfj.jpg

http://img.photobucket.com/albums/v3...psgwdvdewp.jpg

http://img.photobucket.com/albums/v3...psob2lrwu0.jpg

http://img.photobucket.com/albums/v3...psdmqh4wvm.jpg

We took the body off the rotisserie and mounted it on a cart so I could finish the taillight panel and rear valance. I block sanded one more time

http://img.photobucket.com/albums/v3...ps5oes1rxm.jpg

Epoxy primed

http://img.photobucket.com/albums/v3...psowsraj44.jpg

We want to test fit everything before paint. Starting installing the Rod & Custom suspension

http://img.photobucket.com/albums/v3...pspdp7merz.jpg

Back on the ground

http://img.photobucket.com/albums/v3...psxy47z8kb.jpg

Getting ready to install the 347 engine and TKO transmission. Those hoses got to go.

http://img.photobucket.com/albums/v3...ps30zf0zry.jpg

Engine and trans installed

http://img.photobucket.com/albums/v3...psqaoqehsr.jpg

http://img.photobucket.com/albums/v3...pswgw8ia0o.jpg

http://img.photobucket.com/albums/v3...pstooinuzi.jpg

Ididit steering column with a Billet Specialties wheel

http://img.photobucket.com/albums/v3...psybd4kqfq.jpg

A few more photos

http://img.photobucket.com/albums/v3...ps7trpmxs7.jpg

http://img.photobucket.com/albums/v3...psaxhgeawm.jpg

http://img.photobucket.com/albums/v3...pstqjzbb9s.jpg

Brian has the sheetmetal lined up.

http://img.photobucket.com/albums/v3...psiofmu7u7.jpg

Test fitting the new Stang-Aholics front valance

http://img.photobucket.com/albums/v3...psn9xos1cw.jpg

http://img.photobucket.com/albums/v3...psbuphgkwg.jpg

The gas filler will have to be moved down a little because the cap hits the deck lid.

http://img.photobucket.com/albums/v3...pswejd6ty2.jpg

Could you cut a little half moon in the lip of the deck lid to go around the gas cap? Kind of like the cut outs over the tail lights?

That is what Brian said but I want to see if we can lower the filler neck first.

Looking good!