Lateral-g Forums - '68 Nova LS1/T56

I'm putting the Nova up for sale as I just don't seem to drive it much. I'm starting a new business and have no time for the car right now. It's a fun street car that always attracts a crowd at shows. It's turn key reliable and ready to race or just take out for ice cream. The car can be converted back to PT with a wheel change and a shock adjustment. I've had 17x11s on it with 315s and think the car can swallow a 335 if you were careful with backspacing. The 6 speed conversion and new 9 inch have less than 500 miles on them. The trans has 50K on it and has been a great upgrade, making the car more versitile. Looking for $26K. Here's the specs:

1968 Nova

Body

-Finished in Lemans Blue PPG base/clear with semi gloss black Baldwin Motion style stripes bordered in vintage white

-started with completely rust free body with all original sheetmetal (aftermarket steel 4 inch cowl hood)

-New door and hood hinges

-All panels gapped perfectly- doors and trunk shut with minimal effort

-Newer vinyl top with new stainless trim

-Detroit Speed minitub kit installed- trunk finished with factory style look

-S&M race cars 8 point cage with camera mount- custom floor plates

-New mirrors, emblems, door locks, etc

-Paint is in excellent shape with some minor flaws- far better than driver quality- car is shown and does win paint awards

-Entire floor covered in Fatmat sound deadener

Chassis

-QA1 adjustable front billet coilovers

-Addco 1.125 inch sway bar with urethane mounts

-SSBC front brake kit- slotted rotors and billet calipers- Wilwood billet master cyl.

-Unisteer manual rack and pinion steering system with polished stainless link kit

-New urethane bushings, new ball joints, wheel bearings etc

-Competition Engineering subframe connectors

-Inboarded Eaton Detroit leaf springs using Comp engineering rear mounts

-Custom rear shock mounts with Comp Engineering adjustable shocks/ custom lower shock perches for optimal shock angles

-Custom traction bars with adjustable links

-Custom ordered Currie 9 inch rear diff. with 5 inch narrower track to optimize DSE kit (gives more wheel options and a far wider rear lip) – spine braced, filler cap, drain, vent

-new Strange Pro-G nodular third member

-new Detroit Locker, Richmond 4.33 gears

-new 35 spline Moser axles, new bearings and seals

-Centerline Telstar billet wheels- 15 x 7 (new 205/60/15) and 15 x 10 (Mickey Thompson 325/50/15 Drag radial) The car can run an 11 inch wheel and a 315+ tire. The custom narrow housing allows for a 6 inch deep rear lip.

Engine

-2003 LS1 (all aluminum)

-TEA ported heads

-Autokraft oil pan

-Edelbrock motor mounts and coated headers

-Thunder Racing Trex 2.0 cam (242/248 .608/.612 110 LSA)- new LS2 timing chain-matched valve springs, locks, Ti retainers etc

-Thunder Racing new ported and polished LS6 oil pump

-Comp Cams Heavy duty pushrods

-6.0L heavy duty Coil packs and Taylor plug wires

-Edelbrock victor intake manifold and custom Holley HP 750 carb built by Competition Carburetion of Nevada

-MSD 6010 timing controller with easy to use laptop software, custom billet bulkhead harness plate

-2.5 inch exhaust with 3.5 inch electric cutouts, Bullet mufflers, X pipe, and over the axle terminating under the bumper tailpipes

-Meziere billet electric water pump with in-car adjustable speed controller

-Holley blue fuel pump- (-8 delivery line, -8 to carb, Holley reg. with gauge, -8 return line,20 gallon aluminum cell with AN beathers and sump)

-Custom ordered Griffin radiator with 1.5” tubes (-20 AN water lines, 1600 cfm fan) car runs 175-190 on even the hottest days in traffic

-T-56 trans with Hurst billet shifter

-new Monster level 3 clutch

-new Billet steel flywheel

-new ARP hardware

-new Custom tubular trans crossmember with drop out center

-new Quicktime SFI scattershield

-new brand new steel driveshaft by Driveline service with all 1350 Spicer joints

-Custom billet capped center console/ Lokar boot/ Hurst pistol knob with line lock

Interior

-New door panels, hardware, and dash pad

-Custom built gauge panel with billet gauge surround, billet control panels, Autometer gauges and tach

-Corbeau race seats, G force 5 point harnesses, custom rear bulkhead panels and package tray

-New headliner and mirror

-Painless wiring harness

-Lecarra steering wheel

A couple things to fix- gas gauge and volt meter went on the fritz last week. Could be a ground. One of the cutouts has decided to no longer open. All will be fixed before it leaves my garage. The weakest areas are the carpet and a couple tiny spots in the paint that you wouldn't notice unless I pointed them out.

walk around video when it had the auto in it: https://www.youtube.com/watch?v=w0dL_VBNqEI

http://i394.photobucket.com/albums/p...f/DSCN6603.jpg
http://i394.photobucket.com/albums/p...f/motor121.jpg
http://i394.photobucket.com/albums/p...rearcruise.jpg