Lateral-g Forums
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Lateral-g Forums (https://www.lateral-g.net/forums/index.php)
-   Brakes (https://www.lateral-g.net/forums/forumdisplay.php?f=91)
-   -   Kore 3 Rotors fitment (https://www.lateral-g.net/forums/showthread.php?t=37769)

67autocross 07-28-2012 08:39 PM
Kore 3 Rotors fitment
 
1 Attachment(s)
I just picked up some Kore 3 brakes for my Dodge Dart that uses Mustang II front spindles. The first thing I went to mock up was the rotor to the hub, if you look at the picture there is no way it will fit over the wheel studs. Has anyone had any problems with these?

Spiffav8 07-28-2012 08:41 PM
Call Kore3. They will take great care of you!

Vegas69 07-28-2012 10:09 PM
Don't take this the wrong way but the adjacent holes look to be in perfect position. I'm assuming you already tried that though.

FETorino 07-28-2012 11:10 PM
Quote:
Originally Posted by Vegas69 (Post 427389)
Don't take this the wrong way but the adjacent holes look to be in perfect position. I'm assuming you already tried that though.
or not :rolleyes:

67autocross 07-29-2012 12:08 AM
1 Attachment(s)
Quote:
Originally Posted by Vegas69 (Post 427389)
Don't take this the wrong way but the adjacent holes look to be in perfect position. I'm assuming you already tried that though.
Off course...

camcojb 07-29-2012 01:47 AM
Quote:
Originally Posted by 67autocross (Post 427374)
I just picked up some Kore 3 brakes for my Dodge Dart that uses Mustang II front spindles. The first thing I went to mock up was the rotor to the hub, if you look at the picture there is no way it will fit over the wheel studs. Has anyone had any problems with these?
Pretty sure the Darts up to 73 or 74 had that oddball 5 on 4" b.c. which is too small for those rotors. They look to be for the normal 5 on 4.5" and 5 on 4.75". You'd either need different rotors, or have the hubs re-drilled. I'm thinking the hub re-drilling will be the only way to go, because there can't be many rotors in that small bolt circle.

67autocross 07-29-2012 07:55 AM
Quote:
Originally Posted by camcojb (Post 427418)
Pretty sure the Darts up to 73 or 74 had that oddball 5 on 4" b.c. which is too small for those rotors. They look to be for the normal 5 on 4.5" and 5 on 4.75". You'd either need different rotors, or have the hubs re-drilled. I'm thinking the hub re-drilling will be the only way to go, because there can't be many rotors in that small bolt circle.
Both the hubs and the rotor came from Kore3 , I ordered it with 5 on 4.5" so that I could have the bigger bolt pattern. I checked the hub and it matches up with a 5 on 4.5' wheel so I'm guessing the rotor they use must be drilled in house and it is drilled wrong.

camcojb 07-29-2012 09:31 AM
Quote:
Originally Posted by 67autocross (Post 427423)
Both the hubs and the rotor came from Kore3 , I ordered it with 5 on 4.5" so that I could have the bigger bolt pattern. I checked the hub and it matches up with a 5 on 4.5' wheel so I'm guessing the rotor they use must be drilled in house and it is drilled wrong.
Yeah, you'll need to call Tobin on that one. He's a good guy, I'm sure he'll know what's going on.

Apogee 07-30-2012 09:08 AM
Give us a call or shoot us an email and I'm sure we can get it sorted out, whatever the issue may be.

I sent you a PM with my contact information since it looks like you didn't buy these direct from us.

Tobin
KORE3

67autocross 07-30-2012 05:03 PM
1 Attachment(s)
From the top...


All times are GMT -5. The time now is 09:42 AM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Lateral-g.net