1968 Camaro "Badmotorfinger" v2.2

[Ron in SoCal]

Originally Posted by Flash68

Uh yeah.... so our trans swap and oil cooler project turned into this??

Luuuuuucy? You got some 'splain-in to doo!

[Nick.V70]

Looking good Dave, hope you get her back together so we can tear up Danville

[Chad-1stGen]

Dave,

I was wondering how the progress went this weekend. Hopefully that is progress!!

[Flash68]

Originally Posted by itsals1

I've never seen a aftermarket shifter like that! I bet its a great fit on the hand and shortens the throw quite a bit

Travis

I think it will work quite well!

Originally Posted by Ron in SoCal

Luuuuuucy? You got some 'splain-in to doo!

Ron you know how it works.... "well, as long as we are in here let's do ..... bla bla bla bla...." and "we might as well do this"....

Originally Posted by Nor-Cal Nick

Looking good Dave, hope you get her back together so we can tear up Danville

I just hope we got it back together in time for the Buttonwillow weekend!

Originally Posted by Chad-1stGen

Dave,

I was wondering how the progress went this weekend. Hopefully that is progress!!

I think I will call this sideways progress?

[tones2SS]

Let the conversion begin!
I like your new "shifter" beer bottle design.

[Ron in SoCal]

Originally Posted by Flash68

I think it will work quite well!

Ron you know how it works.... "well, as long as we are in here let's do ..... bla bla bla bla...." and "we might as well do this"....

I just hope we got it back together in time for the Buttonwillow weekend!

I think I will call this sideways progress?

More like, (Dave's voice) "Hey Rich, while we're changing out the tranny and modding the clutch, why don't we tear out the interior, dash, do some wiring, put some of that noise/heat sticky stuff in cause you know how comfy I like to be at the track and, oh yeah got any spare aluminum laying around you could trim up for those X brace thingys near the back seats? I'm off to get some beer and I'll be back in the morning. Think you'll have it done?"



(just teasing Bro!)

[GregWeld]

Seriously?! Is that a LIGHT BEER?!

[Flash68]

Originally Posted by tones2SS

Let the conversion begin!
I like your new "shifter" beer bottle design.

Rich only drinks Bud Light... if it were me, it'd be a nice Belgian or hoppier ale.

Originally Posted by Ron in SoCal

More like, (Dave's voice) "Hey Rich, while we're changing out the tranny and modding the clutch, why don't we tear out the interior, dash, do some wiring, put some of that noise/heat sticky stuff in cause you know how comfy I like to be at the track and, oh yeah got any spare aluminum laying around you could trim up for those X brace thingys near the back seats? I'm off to get some beer and I'll be back in the morning. Think you'll have it done?"



(just teasing Bro!)

Ya know, you'd normally be sorta right on that, but in this case I actually did most of the "demo" myself... I mean, it's a lot easier to knock something down than build it up right?

A good way to learn how something gets installed or goes together is to take it apart I hear. We'll see when it's time to put it back in... or leave it out in this case as part of our "race weight" strategic plan.

Originally Posted by GregWeld

Seriously?! Is that a LIGHT BEER?!

Tell me about it... flavored water..... but I don't think Rich, or anyone, would be very productive after 15 of the beers I like to drink.

[Flash68]

We made some progress on the various projects to get ready for Buttonwillow next month. I wish I could just leave the shift rods exposed.