...

Go Back   Lateral-g Forums > Lateral-G Open Discussions > Open Discussion
User Name
Password



Reply
 
Thread Tools Display Modes
  #1  
Old 05-05-2020, 01:17 PM
randy randy is offline
Senior Member
 
Join Date: Jan 2011
Posts: 1,041
Thanks: 3
Thanked 68 Times in 43 Posts
Default

I’m using the Mighty Mouse mood setup. Passenger valve cover and drivers side valve cover are T together And then a line routed between the throttle body and maf. The valley tray goes to the catch can and then catch can to the supercharger Works perfectly.
Attached Images
 
Reply With Quote
  #2  
Old 05-05-2020, 03:37 PM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Thanks randy. The mighty mouse has a built in pressure relief. Do you notice any fuel smell under hard throttle?
Reply With Quote
  #3  
Old 05-05-2020, 04:44 PM
WSSix WSSix is offline
Lateral-g Supporting Member
 
Join Date: Nov 2008
Location: Dunwoody, GA
Posts: 6,618
Thanks: 1,756
Thanked 920 Times in 685 Posts
Default

This is a timely topic. My 540i sucks oil from the PCV system it seems. It's ridiculous in my opinion. I really want to stop this was occurring. It's so bad, that oil is dripping out of my filter down onto the ground in front of the front tire. My Vortech pulls air from below and behind the passenger headlight. I hate it. Everything inside the intake tract is coated in oil. Is this the same thing you guys are fighting? My crank case vent comes in after the MAF and right before the blower.

I don't mind and fully expect some oil to coat the intake tract, but dripping out of my air filter is crap. Almost makes me want to LS swap the BMW
__________________
Trey

Current ride: 2001 BMW 540iT soon to be manual swapped.

Former rides: 1979 Trans Am WS6: LT1/T56, Kore 3 C5/6 brakes, BMW 18in rims

00 BMW 540i/6: Suspension, wheels, and ACS bits.
Reply With Quote
  #4  
Old 05-06-2020, 05:55 AM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Im getting blow by fuel vapor which i think is due to mine having a open filter on the oil vapor side.
Reply With Quote
  #5  
Old 05-06-2020, 06:55 AM
dhutton dhutton is offline
Senior Member
 
Join Date: Nov 2006
Location: Mountain Springs, Texas
Posts: 1,948
Thanks: 1,244
Thanked 580 Times in 317 Posts
Default

I used a dual catch can with two check valves on my LSA. Seems to work well under all boost conditions. Lot of plumbing though.

Don
Reply With Quote
  #6  
Old 05-06-2020, 07:30 AM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Don you running them in line to each other?

These LSA have tons of Plumbing.
Reply With Quote
  #7  
Old 05-07-2020, 04:42 AM
dhutton dhutton is offline
Senior Member
 
Join Date: Nov 2006
Location: Mountain Springs, Texas
Posts: 1,948
Thanks: 1,244
Thanked 580 Times in 317 Posts
Default

Quote:
Originally Posted by nicks67ca View Post
Don you running them in line to each other?

These LSA have tons of Plumbing.
No they are independent but in the same housing. It’s from RX Performance. I installed it a few years ago and I can’t remember all the details but it was for a supercharged application on a CTS-V or ZL1.

Don
Reply With Quote
  #8  
Old 05-06-2020, 06:10 PM
randy randy is offline
Senior Member
 
Join Date: Jan 2011
Posts: 1,041
Thanks: 3
Thanked 68 Times in 43 Posts
Default

None. I spent weeks thinking about this setup and finally went this route. I couldn’t be anymore happy.


Quote:
Originally Posted by nicks67ca View Post
Thanks randy. The mighty mouse has a built in pressure relief. Do you notice any fuel smell under hard throttle?
Reply With Quote
  #9  
Old 05-06-2020, 06:25 PM
WSSix WSSix is offline
Lateral-g Supporting Member
 
Join Date: Nov 2008
Location: Dunwoody, GA
Posts: 6,618
Thanks: 1,756
Thanked 920 Times in 685 Posts
Default

Randy, I didn't find the mood setup on Might Mouse's site. Did you mean mild?
__________________
Trey

Current ride: 2001 BMW 540iT soon to be manual swapped.

Former rides: 1979 Trans Am WS6: LT1/T56, Kore 3 C5/6 brakes, BMW 18in rims

00 BMW 540i/6: Suspension, wheels, and ACS bits.
Reply With Quote
  #10  
Old 05-07-2020, 05:29 AM
nicks67ca nicks67ca is offline
Senior Member
 
Join Date: Oct 2007
Posts: 309
Thanks: 12
Thanked 13 Times in 7 Posts
Default

Quote:
Originally Posted by randy View Post
None. I spent weeks thinking about this setup and finally went this route. I couldn’t be anymore happy.
Thanks Randy, I have an email into MM on a quote. Did you buy the PCV can?
https://www.mightymousesolutions.com...t-page/pcv-can
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 10:00 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright Lateral-g.net