2nd Chance Camaro - Let the Project Begin - Page 161 - Lateral-g Forums

**syborg tt** · #**1601** 07-06-2021, 11:21 PM

Quote:

Originally Posted by ScotI

That's an excellent idea. I do that when jotting down notes & measurements during initial phases but will add that to the mix where applicable.

Thank you.

When I took the car apart (both times) I bag / blue tape the parts and take pictures so when I start putting the car back together I can go back and look at my pictures on the day I took the car apart. It helps jog my memory as it pretty much sucks since Chemo back in 2012.

**syborg tt** · #**1602** 07-30-2021, 05:16 PM

Finally finishing up the Vintage Air heat lines.

Yes something is really really wrong with me

For mock up I am using this plastic reducer.

I can't wait till I don't have to touch this valve again.

**syborg tt** · #**1603** 10-03-2021, 03:53 PM

I missed this one so I am going back to it.

Here is the ground stud that I will be using on the passenger side of the car. It goes directly to the battery and it will be also be a brass bolt.

Firewall fitting test fitted it one last time before I permatex it to the firewall.

Way back somewhere in this thread I put the part number for the machine washers that I am using on the inside of the firewall.

All glued in and nice and tight.

**syborg tt** · #**1604** 10-03-2021, 04:10 PM

Headed back to Ace Hardware for the tenth time this week.

03-21-21

Time to get out the big drill.

**syborg tt** · #**1605** 10-03-2021, 04:21 PM

This is those while I am here moments.

If you know what these are you now how much this project sucks.

I made the right decision by buying the correct tool to remove the spring which made this a much easier task.

I also made sure I drilled reference holes so I could the hinges back in the same place once I removed them.

New bushings installed and on to the next hinge.

Upper hinge should be much easier.

I have said a bunch of cuss words at this point.

Back to Ace hardware...good news I found some chunky bars.

**syborg tt** · #**1606** 10-03-2021, 04:25 PM

Since the transmission lines are close to the downpipe on the header I decided to wrap the lines in DEI Heat Sleeve.

Looking at these hard lines I now know that I am going to have to paint them.
Just one more thing to add to the never ending to do list.

**syborg tt** · #**1607** 10-03-2021, 04:36 PM

So this side didn't go as smoothly as the passenger side.

This tool is a life saver.

Hinge is off and reference marks are set.

This side was not fun.

Both hinges are installed and lets just say the door is way off and I needed a break.

So I off to the taco joint!

I called it a night when I got home and I even broke my rule of cleaning up every night.

**syborg tt** · #**1608** 10-03-2021, 04:39 PM

Since yesterday didn't go so well I decided to make an AC Line.

I plan to crimp the fitting in the engine bay once I have all of the lines in the car.

**syborg tt** · #**1609** 10-03-2021, 04:51 PM

Time to installed the Notch-Head line clamps. Drilling the hole in the frame with the itty-bitty drill bit is very very scary.

**syborg tt** · #**1610** 10-03-2021, 05:12 PM

So I started making notes on the car for things I need to address.

I also need to plug this holes since I am planning on using the Wildwood electric parking brake calipers.

I will be using this wire when I install the Fessler RS light in the RS modified upper valance.

I also need to extend the line as my goal is to hide/clean up as much as of the wiring I can behind the grill.