2nd Chance Camaro - Let the Project Begin

[flyingv]

https://www.prowireusa.com/p-3667-bl...ot-8-2-ga.html

These guys are my go to for all my wiring needs. Normally ship same day too.

Sent from my SM-S906U using Tapatalk

[syborg tt]

Out with the old and in with the New and the good news is the steering wheel is going to a good home right across the street.



Looks like I need to get out my steering wheel remover







I love this wheel from the guys at Screaming Chicken and I can't wait to put on the rest of the parts I grabbed from them.









Old Wheel getting ready to go to it's new home



Cleaned up the warehouse and moved the Flat Hood to safe place so I can get it painted over the winter.



and of course I found the Factory Valve Covers right after I bought a new set.

[syborg tt]

Originally Posted by flyingv

https://www.prowireusa.com/p-3667-bl...ot-8-2-ga.html

These guys are my go to for all my wiring needs. Normally ship same day too.

Sent from my SM-S906U using Tapatalk

Thank you Thank you and I am adding these guys to my contact info.

[syborg tt]

So I found the battery terminal cover and I even bought extra as I know Ron wants a set.

Step One - Trim them a little bit at a time



Trimming just a little more



All Done



Remember that missing Headlight ring I have good news I actually found it.





Wiper Cowl Screen. I still have the original one however, I think a new one is necessary.





I need to pick up a few stainless steel screws to replace them one's I just put in.

[syborg tt]

I am finally installing the Seatbelt Planet seat belts up front and I forgot how nice they look.





Good News is they match the door pull perfectly



Moving over to the Drivers Side



Not sure if I am going to add two more Zipties





I added a washer & nut to the center hump seat belt bolts.






I pulled the passenger seat out as I don't like the how the seat back plates look with the seat bracket.





Plan B or is it C

I moved the set back brackets to the top of seat slider.



With the front seat going back in I decided I should get some temporary seat covers. So off to Autozone I go for Touch Up Paint and Seat Covers !!!!



Good News the seat covers fit great and they are even airbag safe.

[syborg tt]

I hope this will be the last time I have to remove and install the Anvil Close Outs.

Prepping for the Fender Braces and I really wish I new where these came from as I love them and can't remember.





Test Fitting



I need to remove the Anvil pieces for some slight trimmingg.



Man I hope this is enough.





I will be using the hood stops to hold down the outside of the Anvil Close out and to prevent damage to the close out
panel I installed a rubber washer.





Once everything is final I will tighten these down.



I seem to like taking engine bay shots and then looking back at them. I have decided that I will be painting the radiator
and the throttle body black over the winter.

[dontlifttoshift]

Double post

[dontlifttoshift]

What is happening here? Are those bolts tight and the belts can't swivel?




Couple of observations, I can't see your car from here but based on this picture.....

I think the harness bar is backwards. What you have as the front should be the rear. That would allow the belts to point up from the bracket and wrap over the top of the bar to the seat. As it is now, if you ever needed those shoulder harnesses, the seat belt loops themselves are just going to fold up.

If mounted the way I described they would be loaded in tension.

[syborg tt]

Hi Donny,

All of the bolts are tight and the brackets can't swivel. However, since the brackets are so close together I need to put a
washer behind one of them so the brackets can be flat. In the rare occasion that I have a passenger in the back seat I was
worried about them bumping the bracket. On a side note you will have to be one hell of a contortionist to get back there.


Here is a side shot of what it looks like and I am open to your advice as I this is all new to me.

Originally Posted by dontlifttoshift

What is happening here? Are those bolts tight and the belts can't swivel?




Couple of observations, I can't see your car from here but based on this picture.....

I think the harness bar is backwards. What you have as the front should be the rear. That would allow the belts to point up from the bracket and wrap over the top of the bar to the seat. As it is now, if you ever needed those shoulder harnesses, the seat belt loops themselves are just going to fold up.

If mounted the way I described they would be loaded in tension.

[syborg tt]

Well it is finally leaving the garage today.



I had to pull the ramps out of the garage attic.





I love the video from the Ring Camera







I haven't seen the back end of this car in years