2nd Chance Camaro - Let the Project Begin

[Mick Mc]

Originally Posted by syborg tt

2nd Chance Camaro - Cutting out the Stock Wheel Tubs at US Collision

Cutting out the Stock Wheel Tubs at US Collision
Posted: Oct 26, 2011 www.2ndchancecamaro.com

Good Morning All,

Now that the Camaro is at Mario's we can start getting the car ready for the new BF Goodrich KDW2
Tires. The plan for the car is to be street worthy and not look like every other Camaro being built right
now. First and foremost it has to be comfortable to drive and not attract the attention of every Law
Enforcement officer on the road.

Mario did all the work getting the tubs removed and trust me I heard all about how the instructions
sucked and that the DVD wasn't much help either. So I did jump in the car and headed over to his
shop and together we were able to figure out what they wanted us to do.

Step 1:
Trim using the provided templates



Step 2. Cutting the floor.
It doesn't have to be a snug tight fit as the new piece that you will be welding to the floor will take up
some of the gap. Also when you clamp the new wheel tub to the vertical piece it will close up any gap
that may be there. (( Picture will be posted later ))



Mario doing what he does best -- did I mention he called me and my car a bunch of names.



Step 3: Remove Wheel Tub
Make sure there is plenty of clearance to get the new tubs in. That's it - it's that simple.



Step Four: Final Test Fit
Make sure you can slide the new tub in and out easily. If not remove more metal.



Mario did his best to take a couple pictures. Seems Kenny and him are both Experts on the Camera.




Next step is to haul the car to Pro-Tek Powder Coating to for Media Blasting.

All I can say is Mario is a great guy and I can't wait to ride with him to BBT Fab. I am certain that
ride is going to be entertaining.

Well that install seemed easy...


Mick

[syborg tt]

2nd Chance Camaro - Size Does Matter - Which in the end might not Matter
Size Does Matter- Which in the end might not Matter

Posted: Nov 04, 2011 www.2ndchancecamaro.com

Last week I was looking at the tires stored in Mario's 69 Camaro. I couldn't help but notice that his tire
looked skinny compared to the 335 BFG tire sitting in my garage. I kept telling Mario that my 335 was
much bigger then his 345 and he said no way. So I took his tire home to find out if I was correct. I figured
a side by side test would be the only way to prove that the BFG KDW 2 are indeed bigger.

Left: BFG 335 35 18 ( 14" Wide )
Middle: Michelin 345 __ 19 ( 13" Wide )
Right: BFG 295 35 18 ( 12" Wide )




Close up of the BFG 335 & Michelin 345 -- The BFG is 1" Wider




Close Up of the Michelin 345 & the BFG 295 -- Not much of a difference



The BFG 335 height compared to the BFG 295 - you can see the difference is much greater

Also the height is much taller on the Michelin.





The plan has to been to run the 295's on the street and the 335's for Good-Guys events. In the end I may only be able to run the 295 on the back of 2nd Chance Camaro because I can't get the bracket from DSE.

Why you ask ?
The Mini-Tubs I purchased from DSE will fit the 335's. However, since I didn't buy there complete leaf spring conversion kit I am unable to purchase the front offset sping pocket I need to complete the conversion. Where I am confused is I can buy offset shackle & spring perch's but not the lower spring pocket - odd. I had the Allen (really nice sales guy) ask Kyle if I could purchase them and Kyle said no dice which kinda sucks.

So now I may be forced to run only the 295's full time. So Buyer Beware if buy the DSE Mini-Tubs you are going to have to make your own lower mounts for the front or by one of there 3 kits DSE offers. Sometimes you
win sometimes you lose.

I do have a couple Options

Option A:
Buy there Mini-Tub Kit # 041221 $1699.00 which doesn't include Leaf Springs & Shocks which will give you an 1.5" drop and then sell the other parts you don't need. Seems expensive but it's only money and you can't take it with you.

Option B:
Would be to have a local fab shop make a set of offset shackle mounts to complete the conversion. If I go this route I will make a couple extra to help out the two other guys I know that are in the same boat as me.

[MarkM66]

That bugs me when places won't piece out their "kits".

Price it to make money (that's what it's all about right?), either people will buy it, or they won't...

I'd probably just make or have the front shackles made. Have you searched the 2nd gen forums? I'd think someone else may have been down this road..

[MarkM66]

I found this in another post about the front shackles:

"another way is to just flip sides.

The right pocket goes on the inside of the drivers side frame and visa versa. Make mounts for it and reinforce the floor. You have to move the dif and rear mounts in equally too. A better solution would be running a link type suspension."

[DOOM]

Marty always has to show his is bigger than mine..........

[DOOM]

Marty. I just went back and read your last post I thought these were the pictures you sent me a couple a weeks ago so I just paned through them . You did'nt tell me about this DSE ordeal ? I do have a question and I'm not trying to be funny here but did you offer to pay for these spring pockets? I'm shocked that DSE would do this !!! If you wanted them for nothing I would tell to go pound sand to! But if you offered to pay and seeing you have everthing else DSE back there I don't understand what the problem is here. I'll have to give you a call when I get some time.

[syborg tt]

Originally Posted by DOOM

Marty. I just went back and read your last post I thought these were the pictures you sent me a couple a weeks ago so I just paned through them . You did'nt tell me about this DSE ordeal ? I do have a question and I'm not trying to be funny here but did you offer to pay for these spring pockets? I'm shocked that DSE would do this !!! If you wanted them for nothing I would tell to go pound sand to! But if you offered to pay and seeing you have everthing else DSE back there I don't understand what the problem is here. I'll have to give you a call when I get some time.

Yep Offered to pay and no dice & I never asked them for anything free. Heck I just spent $2500.00 with them in the last 8 weeks.

[syborg tt]

Originally Posted by DOOM

Marty always has to show his is bigger than mine..........

Really I am not going to comment here ................

[syborg tt]

2nd Chance Camaro - ProTek Powder Coating Time for Media Blasting

ProTek Powder Coating Time for Media Blasting
Posted: Nov Nov 16, 2011 www.2ndchancecamaro.com

Good Morning,

The car is in the hands of Jay over at ProTek Media blasting. In a couple days we are finally going to know what is hiding under what's left of the paint.






You can see the car took a small hit on the Drivers Side rear but it*doesn't look to bad.





Mario & I both agreed that I should look for a new rear panel since this one is to far gone. Time to see if Tom from Courtyard Camaro
(( [email protected]*)) *has a NOS piece he is willing to sell. If you need Camaro parts he is your guy.




We've got a few holes to fix*from previous body work.



Really, right on the body line - that stinks.




pictures hosted by www.garagescene.net

[syborg tt]

Originally Posted by MarkM66

I found this in another post about the front shackles:

"another way is to just flip sides.

The right pocket goes on the inside of the drivers side frame and visa versa. Make mounts for it and reinforce the floor. You have to move the dif and rear mounts in equally too. A better solution would be running a link type suspension."

Yep I ordered up the rear set up from Ride Tech Looks like I am going Coil-Over. Ride Tech customer service is top notch.