1968 firebird IRS kit - Lateral-g Forums

68brdlvr · #1 10-15-2009, 09:30 AM

Hey all,
Nice place you have here. Like I have read in several post on this site I too have been searching for the ever elusive IRS install kits that don't cost 4500 dollars. So far I have been coming up short and hope you all can point me in the right direction. Even if i could just get the fabrication measurments / instructions to build my own...honestly as a matter of pride I would prefer this method.

Anyway...I would be greatful for any help I can get.

Thanks!

**GregWeld** · #2 10-15-2009, 11:20 AM

I'm hunting for a supplier builder that does IRS stuff - will post it as soon as I come up with it.

In the meantime -- here's a handy dandy DIY bracket supplier you might find handy for many things while you're fabricating.

http://www.welderseries.com/

**GregWeld** · #3 10-15-2009, 11:26 AM

These guys have "kits" for Corvette IRS installs...

The prices you're quoting - 4K - etc -- would include the rear suspension... apparently you don't need those parts - you're just looking for brackets and instructions... ??

So try these guys:

http://www.progressiveautomotive.com/sweetrear.htm

68brdlvr · #4 10-15-2009, 12:25 PM

Quote:

Originally Posted by GregWeld

These guys have "kits" for Corvette IRS installs...

The prices you're quoting - 4K - etc -- would include the rear suspension... apparently you don't need those parts - you're just looking for brackets and instructions... ??

So try these guys:

http://www.progressiveautomotive.com/sweetrear.htm

Hey thanks for the response:

The cheapest quote I have had for the brackets alone (Ron Wilson) was 925.00 plus shipping. Still pretty steep for what it is! I have the tools to fab...I would really like the knowledge in order to do it myself. That being said I saw someone on here built one for like 425.00...I would forgo doing it myself for a deal like that...ha.

I may just have to take 10ccs of SIU and finger it out freestyle.

Thanks for the weldseries link, this will definelty help.

Beach Cruiser · #5 10-15-2009, 04:19 PM

I built my own for my 67 Camaro. Really wasn't too hard to do. Here's a pic.

68brdlvr · #6 10-15-2009, 04:38 PM

That is just what the doctor ordered! I was wondering what to do about the forward links as most setups cut open the back seat...now i know. Other than just running them forward and apart does the location of those links hurt performance or are they just there to hold things put?

Thanks very much.

68brdlvr · #7 10-16-2009, 09:28 AM

Quote:

Originally Posted by GregWeld

These guys have "kits" for Corvette IRS installs...

The prices you're quoting - 4K - etc -- would include the rear suspension... apparently you don't need those parts - you're just looking for brackets and instructions... ??

So try these guys:

http://www.progressiveautomotive.com/sweetrear.htm

FYI

They don't make them for camaros or firebirds because they are unibody, was the reply I got back from them.

Thanks again though

Beach Cruiser · #8 10-16-2009, 01:34 PM

a .dxf is a cad drawing file that your local shop can use to CNC the parts out with a plasma or waterjet table.

Way better than the old tourch or cutoff wheel method.

Where's the area I got to get to for free beers?

68brdlvr · #9 10-16-2009, 01:39 PM

Quote:

Originally Posted by Beach Cruiser

a .dxf is a cad drawing file that your local shop can use to CNC the parts out with a plasma or waterjet table.

Way better than the old tourch or cutoff wheel method.

Where's the area I got to get to for free beers?

Hood....I mean Woodbridge, VA