WTB or trade for some Big Block Chevy parts...

[BBC71Nova]

I have a good bit of bbc parts. What are you looking for? I keep changing my mind on things so it's mostly all new stuff

[Vegas69]

I have a set of billet valve covers and a circle track style air cleaner, both brand new. Your choice on a used 14 x 3 or 14 x 4 new air cleaner element. I'd let you have them if you covered the shipping...

If you have Wilwood brakes, I have some brake pads that I can send you as well.

[69MyWay]

Originally Posted by Vegas69

I have a set of billet valve covers and a circle track style air cleaner, both brand new. Your choice on a used 14 x 3 or 14 x 4 new air cleaner element. I'd let you have them if you covered the shipping...

If you have Wilwood brakes, I have some brake pads that I can send you as well.

WOW WOW WOW WOW!!!!!!!!!!!!! These parts are AMAZING!!!!!! Now...if the rest of the car looked as nice! My wife is thrilled. Thank you!

Now...going to look at some other stuff on Friday...and thanks to everybody here that has been making me offers on stuff. I hope to sew up the main needs here quickly...

If all goes well the FRAME will be able to sit on four wheels in a few day, and then we jump full speed into the powerplant so I can slam the body back on and get to the other stuff.

[Greenhead]

Originally Posted by BBC71Nova

I have a good bit of bbc parts. What are you looking for? I keep changing my mind on things so it's mostly all new stuff

I am gathering interior parts right now. I need a tilt column,good factory dash gauge carrier without clock or anything for a 700r conversion

[Vega$69]

I have a nice set of Stainless Works BBC headers. Polished. Used in very good condition.

I also have a fresh 4 bolt main short block less cam. 427 6233 Crank pink rods new forged Pistons

Was gonna do a Yenko close and went LS instead. Lol

[69MyWay]

Don't go too far (put any $$$) into checking out the 290 heads...just wondering what kind of shape their in - have to figure shipping to zip 61727 - and I think they are around 50 lbs each...right?

Fedex is a NO-go where I am...they are terrible.

Vegas...YES - I'd be down with those parts...Right now we just have stock sheet valve covers and no air cleaner...and I'll be running one on top like that. Will need to get an extreme drop down base to clear the hood - been there done that.


She has 781 heads right now - I guess they are the open chamber version of the 290 - Either would work...but when I took the motor apart ($200 craigslist buy) - one of the exhaust valves fell out - snapped off clean on the stem. Probably going to be some issues there. I haven't taken them to the machine shop yet. I'm hoping to get the frame out to sandblasting next week and get the block to the machine shop - and I'll know if anything I have can be salvaged - those 290s would be the next way to go.

The car has a 4:11 rear through a LT1 T56 - So...I'd like to be able to turn some RPM on the low side...and that would be rectangle port heads and stuff - but she wants a daily driver and that puts me back to the oval peanut ports...

Obviously, I'm seeing what we can scrap together on the motor for now - can always re-visit it...but right now it needs to run...not win any 1/4 mile grudge matches.

[69MyWay]

I don't have any 700R4 stuff to trade...and I only have the one console right now. I do have two sets of stock 69 Vette suspension parts - a power steering system complete (less the pump).

[MrCortez]

I don't know if you need this stuff but I have a 69 fbody sbc and a BBC Muncie crossmember and a BBC mark iv stock oil pan that is was lightly used but has been sitting outside.

[69MyWay]

Originally Posted by MrCortez

I don't know if you need this stuff but I have a 69 fbody sbc and a BBC Muncie crossmember and a BBC mark iv stock oil pan that is was lightly used but has been sitting outside.

Oil pan is a big maybe. Would it be much trouble to measure it for depth at the lowest/deepest part from where it meets the block?

I have a pan - but it is a truck/RV pan and may be too deep for the Vette.

[69MyWay]

Originally Posted by Vega$69

I have a nice set of Stainless Works BBC headers. Polished. Used in very good condition.

I also have a fresh 4 bolt main short block less cam. 427 6233 Crank pink rods new forged Pistons

Was gonna do a Yenko close and went LS instead. Lol

I'm hoping my block is good - you don't happen to have an HEI distributor laying around for that do you?